Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: Vastlopers in Nautilus  (gelezen 5240 keer)

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Gepost op: 2006/12/27, 17:50:41 »
Hoi,

Ik post ook maar weer 'ns iets.

Het gebeurt mij erg vaak dat m'n systeem blijft 'hangen'. Vaak gewoon tijdens het navigeren tussen mappen. Alleen de aanwijzer van de muis doet het dan  nog, verder reageert 'ie nergens meer op. Soms kan ik na CTRL+BACKSPACE weer inloggen, andere keren werkt alleen het lang ingedrukt houden van de uit-knop van de PC.

Ik had dit probleem al een tijdje in Dapper, ik hoopte dat een clean install wat zou oplossen, maar helaas hij doet het nog steeds (nu in Edgy).

Zijn er mensen met soortgelijke ervaringen?
Of iemand met een idee waar het aan zou kunnen liggen?
Of (nog beter) iemand met een oplossing?

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #1 Gepost op: 2006/12/29, 11:40:12 »
Zou het aan de driver voor de grafische kaart kunnen liggen?
Ik heb een laptop met 'n nVidia GeForce FX, maar heb daar nog geen speciale driver voor geïnstalleerd, omdat alles gewoon lijkt te werken.

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #2 Gepost op: 2006/12/29, 11:43:10 »
die nvidia-drivers installeren kan in ieder geval geen kwaad.
welk type is het?

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #3 Gepost op: 2006/12/29, 11:45:53 »
lspci|grep VGA in de terminal geeft het type graf. kaart.

waarsch. kun je de fx gewoon via:
 https://help.ubuntu.com/community/BinaryDriverHowto/Nvidia
installeren, waarbij je via de synaptic de juiste restricted modules installeert.

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #4 Gepost op: 2006/12/29, 14:28:21 »
Bedankt, ik krijg nu een nVidia scherm bij het opstarten. Ik weet dat ik dat kan uitzetten, maar ik laat het maar zo. Mocht het scherm dan niet meer verschijnen na een kernel update, dan weet ik meteen dat de driver opnieuw geínstalleerd moet worden.

Nu maar hopen dat dit de oplossing is voor m'n vastlopers. Zo niet, dan moet ik Suse maar 'ns proberen. Daar is m'n zwager zeer over te spreken.

Mocht iemand in de tussentijd nog andere ideeën hebben over waarom het scherm zomaar kan bevriezen, dan lees ik dat graag.

Gisteren bevroor m'n scherm terwijl ik in OOo Calc werkte. Dit werd voorafgegaan door het steeds trager bewegen van het werkblad bij het naar beneden scrollen (niet met de scroll balk, maar met de pijltjestoets.

Misschien brengt dat nog iemand op een idee.

btw, waarom wordt zowat ieder woord dat ik hier intik onderlijnd alsof het verkeerd gespeld is?

Offline Kiwinote

  • Lid
    • Launchpad
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #5 Gepost op: 2006/12/29, 14:30:45 »
Het kan aan je hoeveelheid ram liggen...
Heb je in firefox de engelse spellcheck aangezet of zo?

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #6 Gepost op: 2007/01/02, 09:26:10 »
Hmm.. toch weer een bevroren scherm. Zelf crtl alt backspace werkte niet.
Dit begint wel vervelend te worden.

Zijn er geen mensen met verstand van zaken die aan een log-bestand o.i.d. kunnen zien waardoor het geheugen steeds volloopt (of wat de oorzaak van een bevroren scherm verder ook mag zijn)?

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #7 Gepost op: 2007/01/02, 09:52:05 »
je zou tijdens het werken met applicatie/programma's eens een TOP kunnen doen. =top= in de terminal, en de uitkomst hier posten. ik hen dit probleem ook wel eens gehad, en bleek mijn processor 100% te draaien....(door een proces)

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #8 Gepost op: 2007/01/02, 10:04:18 »
Tnx, ik zal het thuis 'ns proberen. Kun je TOP laten monitoren en dan doorwerken tot het misgaat, of krijg je met TOP alleen een momentopname?

Er zijn toch ook log-bestanden? Kun je daar het processorgebruik niet in zien?

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #9 Gepost op: 2007/01/02, 10:17:27 »
=top= /procesbeheer en systemlog zijn de manieren om in eerste instantie te kijken of er iets aan de hand is.
top kun je laten draaien op de achtergrond. zelf heb ik =gkrellm= als systemmonitor.

Jeej

  • Gast
Vastlopers in Nautilus
« Reactie #10 Gepost op: 2007/01/02, 13:17:48 »
Citaat van: Jelle
Zijn er mensen met soortgelijke ervaringen?
Yep, jammer genoeg wel.
Citaat van: Jelle
Of iemand met een idee waar het aan zou kunnen liggen?
Nope.
Citaat van: Jelle
Of (nog beter) iemand met een oplossing?
Nope, ik draai nu geen gnome maar maar xfce, nu loopt ie niet meer daar op vast.

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #11 Gepost op: 2007/01/02, 13:20:55 »
Citaat van: Jeej
Citaat van: Jelle
Zijn er mensen met soortgelijke ervaringen?
Yep, jammer genoeg wel.
Citaat van: Jelle
Of iemand met een idee waar het aan zou kunnen liggen?
Nope.
Citaat van: Jelle
Of (nog beter) iemand met een oplossing?
Nope, ik draai nu geen gnome maar maar xfce, nu loopt ie niet meer daar op vast.
hoeveel ram-geheugen heb je jeej?

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #12 Gepost op: 2007/01/02, 20:02:11 »
top - 20:00:03 up 19 min,  2 users,  load average: 0.71, 0.49, 0.34
Tasks:  97 total,   2 running,  95 sleeping,   0 stopped,   0 zombie
Cpu(s): 12.7%us,  3.8%sy,  0.0%ni, 82.3%id,  0.0%wa,  0.7%hi,  0.5%si,  0.0%st
Mem:    515328k total,   506388k used,     8940k free,    61180k buffers
Swap:  1052248k total,        0k used,  1052248k free,   222380k cached

  PID USER      PR  NI  VIRT  RES  SHR S %CPU %MEM    TIME+  COMMAND            
 4945 jelle     15   0 34644  15m  11m S   20  3.0   2:44.52 gnome-system-mo    
 4189 root      16   0 40648  28m 8536 R    8  5.6   1:49.29 Xorg              
 5445 jelle     15   0 52012  14m 9904 S    4  3.0   0:03.91 gnome-terminal    
 4343 haldaemo  16   0  2032  840  716 S    0  0.2   0:00.59 hald-addon-stor    
 4660 jelle     15   0 16316 9352 6736 S    0  1.8   0:06.85 metacity          
 4876 jelle     15   0  201m  79m  47m S    0 15.7   0:38.57 soffice.bin        
 5066 cupsys    26  10  4544 1952 1444 S    0  0.4   0:00.66 cupsd              
 5470 jelle     16   0  2252 1128  844 R    0  0.2   0:00.46 top                
    1 root      16   0  1628  532  448 S    0  0.1   0:01.03 init              
    2 root      RT   0     0    0    0 S    0  0.0   0:00.00 migration/0        
    3 root      34  19     0    0    0 S    0  0.0   0:00.00 ksoftirqd/0        
    4 root      RT   0     0    0    0 S    0  0.0   0:00.00 watchdog/0        
    5 root      RT   0     0    0    0 S    0  0.0   0:00.00 migration/1        
    6 root      34  19     0    0  


Dit is de output van TOP met een flink aantal vensters open, maar nog geen problemen.

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #13 Gepost op: 2007/01/02, 20:18:23 »
top - 20:07:26 up 27 min,  2 users,  load average: 0.61, 0.43, 0.35
Tasks:  95 total,   3 running,  92 sleeping,   0 stopped,   0 zombie
Cpu(s): 21.3%us,  3.1%sy,  0.0%ni, 74.6%id,  0.0%wa,  0.7%hi,  0.3%si,  0.0%st
Mem:    515328k total,   463308k used,    52020k free,    43344k buffers
Swap:  1052248k total,     7644k used,  1044604k free,   216728k cached

  PID USER      PR  NI  VIRT  RES  SHR S %CPU %MEM    TIME+  COMMAND            
 4189 root      16   0 34432  24m 7704 R   21  4.8   2:22.28 Xorg              
 4667 jelle     15   0 90704  36m  18m S   12  7.3   0:16.77 nautilus          
 4660 jelle     15   0 16340 9488 6744 R    7  1.8   0:11.93 metacity          
 4665 jelle     16   0 43148  18m  13m S    6  3.7   0:13.30 gnome-panel        
 5445 jelle     15   0 52020  14m 9948 S    2  3.0   0:07.00 gnome-terminal    
 4642 jelle     15   0 28932 9896 7904 S    1  1.9   0:02.73 gnome-settings-    
 4876 jelle     15   0  218m  88m  52m S    1 17.5   1:03.66 soffice.bin        
 4766 jelle     15   0 15636 2704 1740 S    0  0.5   0:01.68 gnome-screensav    
 5470 jelle     16   0  2252 1128  844 R    0  0.2   0:02.33 top                
    1 root      16   0  1628  532  448 S    0  0.1   0:01.03 init              
    2 root      RT   0     0    0    0 S    0  0.0   0:00.00 migration/0        
    3 root      34  19     0    0    0 S    0  0.0   0:00.00 ksoftirqd/0        
    4 root      RT   0     0    0    0 S    0  0.0   0:00.00 watchdog/0        
    5 root      RT   0     0    0    0 S    0  0.0   0:00.00 migration/1        
    6 root      34  19     0    0    0 S    0  0.0   0:00.00 ksoftirqd/1        
    7 root      RT   0     0    0    0 S    0  0.0   0:00.00 watchdog/1    

Hier nog maar 'ns eentje.

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #14 Gepost op: 2007/01/03, 13:41:11 »
Geeft dit al aanwijzingen voor de oorzaak van de vastlopers? Ik kan er alleen uit opmaken dat er weinig CPU gebruikt wordt en veel geheugen.

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #15 Gepost op: 2007/01/03, 15:03:36 »
Citaat van: Jelle
Geeft dit al aanwijzingen voor de oorzaak van de vastlopers? Ik kan er alleen uit opmaken dat er weinig CPU gebruikt wordt en veel geheugen.
exact. meer conclusies kan ik er helaas ook niet aan verbinden.

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #16 Gepost op: 2007/01/04, 11:51:59 »
Gisteravond twee vastlopers gehad. Zelfs CTRL ALT F6 werkt dan niet, dus ik kan geen TOP output posten van het moment dat het systeem vastzit.

Ik vermoed dat gisteren een andere oorzaak had dan normaal. Ik was namelijk XP aan het installeren in VMWare player. TOP gaf aan (toen alles nog gewoon draaide) dat VMWare player zo nu en dan een CPU gebruik wist te bereiken van 111%.

Offline Kiwinote

  • Lid
    • Launchpad
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #17 Gepost op: 2007/01/04, 16:17:07 »
Overclocking :)

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #18 Gepost op: 2007/01/04, 18:59:21 »
?????

Offline Dave

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #19 Gepost op: 2007/01/04, 19:13:36 »
vanmiddag een vastloper.
gisteren een nieuwe install gedaan (zie ander topic)
Nog geen aparte nvidia drivers geinstalleerd enzo want vond het beeld en de leesbaarheid wel goed eigenlijk.

Jeej

  • Gast
Vastlopers in Nautilus
« Reactie #20 Gepost op: 2007/01/04, 20:55:59 »
Citaat van: leoquant
hoeveel ram-geheugen heb je jeej?
Ik heb 192 mb geheugen.
Maar het is nogsteeds niet geweldig, Kijk maar... :(

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #21 Gepost op: 2007/01/04, 21:35:10 »
Citaat van: Jeej
Citaat van: leoquant
hoeveel ram-geheugen heb je jeej?
Ik heb 192 mb geheugen.
Maar het is nogsteeds niet geweldig, Kijk maar... :(
yep gezien. wanneer het een hardware probleem is.....:(

Offline Kiwinote

  • Lid
    • Launchpad
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #22 Gepost op: 2007/01/04, 21:41:19 »
Citaat van: Kiwinote
Overclocking :)
Bedoelde dat het je de indruk geeft dat er wordt overgeclockt met 111%

Offline Jelle

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #23 Gepost op: 2007/01/24, 21:46:31 »
[17179569.184000] Linux version 2.6.17-10-generic (root@terranova) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Tue Dec 5 22:28:26 UTC 2006 (Ubuntu 2.6.17-10.34-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[17179569.184000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
[17179569.184000]  BIOS-e820: 000000001ff70000 - 000000001ff79000 (ACPI data)
[17179569.184000]  BIOS-e820: 000000001ff79000 - 000000001ff80000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 511MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f69f0
[17179569.184000] On node 0 totalpages: 130928
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   Normal zone: 126832 pages, LIFO batch:31
[17179569.184000] DMI present.
[17179569.184000] ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6a10
[17179569.184000] ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x1ff746ea
[17179569.184000] ACPI: FADT (v001 INTEL  SPDG     0x06040000 PTL  0x00000003) @ 0x1ff78e88
[17179569.184000] ACPI: MADT (v001 PTLTD   APIC   0x06040000  LTP 0x00000000) @ 0x1ff78efc
[17179569.184000] ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x1ff78f5a
[17179569.184000] ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @ 0x1ff78f82
[17179569.184000] ACPI: DSDT (v001   WIST      K2M 0x06040000 MSFT 0x0100000e) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x1008
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[17179569.184000] Processor #1 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda2 ro splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[17179569.184000] Detected 3059.527 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179569.516000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179569.516000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179569.524000] Memory: 509544k/523712k available (1910k kernel code, 13628k reserved, 1069k data, 308k init, 0k highmem)
[17179569.524000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179569.604000] Calibrating delay using timer specific routine.. 6125.10 BogoMIPS (lpj=12250210)
[17179569.604000] Security Framework v1.0.0 initialized
[17179569.604000] SELinux:  Disabled at boot.
[17179569.604000] Mount-cache hash table entries: 512
[17179569.604000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179569.604000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179569.604000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179569.604000] CPU: L2 cache: 512K
[17179569.604000] CPU: Hyper-Threading is disabled
[17179569.604000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
[17179569.604000] Checking 'hlt' instruction... OK.
[17179569.620000] SMP alternatives: switching to UP code
[17179569.620000] checking if image is initramfs... it is
[17179570.016000] Freeing initrd memory: 5322k freed
[17179570.016000] ACPI: Core revision 20060707
[17179570.016000] ACPI: Looking for DSDT ... not found!
[17179570.020000] CPU0: Intel Mobile Intel(R) Pentium(R) 4     CPU 3.06GHz stepping 09
[17179570.020000] SMP alternatives: switching to SMP code
[17179570.024000] Booting processor 1/1 eip 3000
[17179570.032000] Initializing CPU#1
[17179570.112000] Calibrating delay using timer specific routine.. 6118.88 BogoMIPS (lpj=12237774)
[17179570.112000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179570.112000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179570.112000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179570.112000] CPU: L2 cache: 512K
[17179570.112000] CPU: Hyper-Threading is disabled
[17179570.112000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
[17179570.112000] CPU1: Intel Mobile Intel(R) Pentium(R) 4     CPU 3.06GHz stepping 09
[17179570.112000] Total of 2 processors activated (12243.99 BogoMIPS).
[17179570.112000] ENABLING IO-APIC IRQs
[17179570.112000] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[17179570.256000] checking TSC synchronization across 2 CPUs: passed.
[17179570.260000] Brought up 2 CPUs
[17179570.288000] migration_cost=4000
[17179570.292000] NET: Registered protocol family 16
[17179570.292000] EISA bus registered
[17179570.292000] ACPI: bus type pci registered
[17179570.292000] PCI: PCI BIOS revision 2.10 entry at 0xfd822, last bus=3
[17179570.292000] PCI: Using configuration type 1
[17179570.292000] Setting up standard PCI resources
[17179570.304000] ACPI: Interpreter enabled
[17179570.304000] ACPI: Using IOAPIC for interrupt routing
[17179570.304000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179570.304000] PCI: Probing PCI hardware (bus 00)
[17179570.308000] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[17179570.308000] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[17179570.308000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[17179570.308000] Boot video device is 0000:01:00.0
[17179570.308000] PCI: Transparent bridge - 0000:00:1e.0
[17179570.308000] PCI: Bus #04 (-#07) is hidden behind transparent bridge #03 (-#03) (try 'pci=assign-busses')
[17179570.308000] Please report the result to linux-kernel to fix this permanently
[17179570.308000] PCI: Bus #08 (-#0b) is hidden behind transparent bridge #03 (-#03) (try 'pci=assign-busses')
[17179570.308000] Please report the result to linux-kernel to fix this permanently
[17179570.308000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179570.316000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[17179570.316000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[17179570.316000] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 *11 14 15)
[17179570.316000] ACPI: PCI Interrupt Link [LNKB] (IRQs *10 11 14 15)
[17179570.320000] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11 14 15)
[17179570.320000] ACPI: PCI Interrupt Link [LNKD] (IRQs *10 11 14 15)
[17179570.320000] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 *11 14 15)
[17179570.320000] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11 14 15) *0, disabled.
[17179570.320000] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11 14 15) *0, disabled.
[17179570.320000] ACPI: PCI Interrupt Link [LNKH] (IRQs *10 11 14 15)
[17179570.324000] ACPI: Embedded Controller [EC] (gpe 28) interrupt mode.
[17179570.328000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179570.328000] pnp: PnP ACPI init
[17179570.332000] pnp: PnP ACPI: found 11 devices
[17179570.332000] PnPBIOS: Disabled by ACPI PNP
[17179570.332000] PCI: Using ACPI for IRQ routing
[17179570.332000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179570.340000] PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:01:00.0
[17179570.340000] PCI: Bridge: 0000:00:01.0
[17179570.340000]   IO window: disabled.
[17179570.340000]   MEM window: d1000000-d1ffffff
[17179570.340000]   PREFETCH window: e0000000-efffffff
[17179570.340000] PCI: Bus 4, cardbus bridge: 0000:03:04.0
[17179570.340000]   IO window: 00003400-000034ff
[17179570.340000]   IO window: 00003800-000038ff
[17179570.344000]   PREFETCH window: 30000000-31ffffff
[17179570.344000]   MEM window: 36000000-37ffffff
[17179570.344000] PCI: Bus 8, cardbus bridge: 0000:03:04.1
[17179570.344000]   IO window: 00003c00-00003cff
[17179570.344000]   IO window: 00002400-000024ff
[17179570.344000]   PREFETCH window: 32000000-33ffffff
[17179570.344000]   MEM window: 38000000-39ffffff
[17179570.344000] PCI: Bridge: 0000:00:1e.0
[17179570.344000]   IO window: 3000-3fff
[17179570.344000]   MEM window: d2000000-d20fffff
[17179570.344000]   PREFETCH window: 30000000-34ffffff
[17179570.344000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[17179570.344000] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 20 (level, low) -> IRQ 177
[17179570.344000] ACPI: PCI Interrupt 0000:03:04.1[b] -> GSI 21 (level, low) -> IRQ 185
[17179570.344000] NET: Registered protocol family 2
[17179570.388000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[17179570.388000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[17179570.388000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[17179570.388000] TCP: Hash tables configured (established 16384 bind 8192)
[17179570.388000] TCP reno registered
[17179570.388000] Simple Boot Flag at 0x36 set to 0x1
[17179570.388000] audit: initializing netlink socket (disabled)
[17179570.388000] audit(1169673081.388:1): initialized
[17179570.388000] VFS: Disk quotas dquot_6.5.1
[17179570.388000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179570.388000] Initializing Cryptographic API
[17179570.388000] io scheduler noop registered
[17179570.388000] io scheduler anticipatory registered
[17179570.388000] io scheduler deadline registered
[17179570.388000] io scheduler cfq registered (default)
[17179570.388000] isapnp: Scanning for PnP cards...
[17179570.744000] isapnp: No Plug & Play device found
[17179570.768000] Real Time Clock Driver v1.12ac
[17179570.768000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179570.768000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[17179570.768000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179570.768000] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[17179570.768000] ACPI: PCI Interrupt 0000:00:1f.6[b] -> GSI 17 (level, low) -> IRQ 193
[17179570.768000] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[17179570.768000] mice: PS/2 mouse device common for all mice
[17179570.772000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179570.772000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179570.772000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179570.772000] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[17179570.780000] i8042.c: Detected active multiplexing controller, rev 1.9.
[17179570.784000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[17179570.784000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[17179570.784000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[17179570.792000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[17179570.792000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179570.792000] EISA: Probing bus 0 at eisa.0
[17179570.792000] Cannot allocate resource for EISA slot 1
[17179570.792000] Cannot allocate resource for EISA slot 2
[17179570.792000] Cannot allocate resource for EISA slot 3
[17179570.792000] EISA: Detected 0 cards.
[17179570.792000] TCP bic registered
[17179570.792000] NET: Registered protocol family 1
[17179570.792000] NET: Registered protocol family 8
[17179570.792000] NET: Registered protocol family 20
[17179570.792000] Starting balanced_irq
[17179570.792000] Using IPI No-Shortcut mode
[17179570.792000] ACPI: (supports S0 S3 S4 S5)
[17179570.792000] Freeing unused kernel memory: 308k freed
[17179570.952000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179571.888000] Capability LSM initialized
[17179571.976000] ACPI: Processor [CPU0] (supports 8 throttling states)
[17179571.980000] ACPI: Thermal Zone [THM0] (24 C)
[17179572.464000] ICH5: IDE controller at PCI slot 0000:00:1f.1
[17179572.464000] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[17179572.464000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 201
[17179572.464000] ICH5: chipset revision 2
[17179572.464000] ICH5: not 100% native mode: will probe irqs later
[17179572.464000]     ide0: BM-DMA at 0x2060-0x2067, BIOS settings: hda:DMA, hdb:pio
[17179572.464000]     ide1: BM-DMA at 0x2068-0x206f, BIOS settings: hdc:DMA, hdd:pio
[17179572.464000] Probing IDE interface ide0...
[17179572.756000] hda: TOSHIBA MK8032GAX, ATA DISK drive
[17179573.428000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179573.456000] Probing IDE interface ide1...
[17179574.192000] hdc: HL-DT-ST DVD-RW GWA-4040N, ATAPI CD/DVD-ROM drive
[17179574.528000] ide1 at 0x170-0x177,0x376 on irq 15
[17179574.540000] hda: max request size: 512KiB
[17179574.540000] hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
[17179574.540000] hda: cache flushes supported
[17179574.540000]  hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
[17179574.596000] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[17179574.596000] Uniform CD-ROM driver Revision: 3.20
[17179575.084000] usbcore: registered new driver usbfs
[17179575.084000] usbcore: registered new driver hub
[17179575.084000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 209
[17179575.084000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[17179575.084000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[17179575.084000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[17179575.084000] ehci_hcd 0000:00:1d.7: debug port 1
[17179575.084000] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[17179575.084000] ehci_hcd 0000:00:1d.7: irq 209, io mem 0xd0000000
[17179575.088000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179575.088000] usb usb1: configuration #1 chosen from 1 choice
[17179575.088000] hub 1-0:1.0: USB hub found
[17179575.088000] hub 1-0:1.0: 8 ports detected
[17179575.120000] USB Universal Host Controller Interface driver v3.0
[17179575.152000] ieee1394: Initialized config rom entry `ip1394'
[17179575.352000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 217
[17179575.352000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[17179575.352000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[17179575.352000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[17179575.352000] uhci_hcd 0000:00:1d.0: irq 217, io base 0x00001cc0
[17179575.356000] usb usb2: configuration #1 chosen from 1 choice
[17179575.356000] hub 2-0:1.0: USB hub found
[17179575.356000] hub 2-0:1.0: 2 ports detected
[17179575.460000] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 225
[17179575.460000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[17179575.460000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[17179575.460000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[17179575.460000] uhci_hcd 0000:00:1d.1: irq 225, io base 0x00001ce0
[17179575.460000] usb usb3: configuration #1 chosen from 1 choice
[17179575.460000] hub 3-0:1.0: USB hub found
[17179575.460000] hub 3-0:1.0: 2 ports detected
[17179575.568000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 201
[17179575.568000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[17179575.568000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[17179575.568000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[17179575.568000] uhci_hcd 0000:00:1d.2: irq 201, io base 0x00002000
[17179575.568000] usb usb4: configuration #1 chosen from 1 choice
[17179575.568000] hub 4-0:1.0: USB hub found
[17179575.568000] hub 4-0:1.0: 2 ports detected
[17179575.672000] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 217
[17179575.672000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[17179575.672000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[17179575.672000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[17179575.672000] uhci_hcd 0000:00:1d.3: irq 217, io base 0x00002020
[17179575.672000] usb usb5: configuration #1 chosen from 1 choice
[17179575.672000] hub 5-0:1.0: USB hub found
[17179575.672000] hub 5-0:1.0: 2 ports detected
[17179575.780000] ACPI: PCI Interrupt 0000:03:04.2[C] -> GSI 23 (level, low) -> IRQ 209
[17179575.832000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[209]  MMIO=[d2007000-d20077ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[17179575.944000] kjournald starting.  Commit interval 5 seconds
[17179575.944000] EXT3-fs: mounted filesystem with ordered data mode.
[17179575.964000] usb 3-1: new low speed USB device using uhci_hcd and address 2
[17179576.144000] usb 3-1: configuration #1 chosen from 1 choice
[17179577.104000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[000ae4041810352d]
[17179586.380000] input: PC Speaker as /class/input/input1
[17179587.056000] Linux agpgart interface v0.101 (c) Dave Jones
[17179587.060000] agpgart: Detected an Intel 865 Chipset.
[17179587.068000] agpgart: AGP aperture is 128M @ 0x40000000
[17179587.336000] irda_init()
[17179587.336000] NET: Registered protocol family 23
[17179587.376000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179587.380000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179587.444000] hw_random: RNG not detected
[17179587.560000] ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 17 (level, low) -> IRQ 193
[17179587.560000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[17179587.740000] usbcore: registered new driver hiddev
[17179587.756000] input: Microsoft Basic Optical Mouse as /class/input/input2
[17179587.756000] input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.1-1
[17179587.756000] usbcore: registered new driver usbhid
[17179587.756000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179587.856000] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
[17179587.900000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[17179587.904000] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 3.
[17179587.904000] nsc-ircc, chip->init
[17179587.904000] nsc-ircc, Found chip at base=0x02e
[17179587.904000] nsc-ircc, driver loaded (Dag Brattli)
[17179587.904000] nsc_ircc_open(), can't get iobase of 0x2f8
[17179587.904000] nsc-ircc, Found chip at base=0x02e
[17179587.904000] nsc-ircc, driver loaded (Dag Brattli)
[17179587.904000] nsc_ircc_open(), can't get iobase of 0x2f8
[17179587.904000] pnp: Device 00:0a disabled.
[17179587.936000] ts: Compaq touchscreen protocol output
[17179587.980000] nvidia: module license 'NVIDIA' taints kernel.
[17179588.016000] Loaded prism54 driver, version 1.2
[17179588.052000] 8139too Fast Ethernet driver 0.9.27
[17179588.384000] intel8x0_measure_ac97_clock: measured 55444 usecs
[17179588.384000] intel8x0: clocking to 48000
[17179588.384000] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 201
[17179588.388000] eth0: uploading firmware...
[17179588.516000] eth0: firmware version: 1.0.4.3
[17179588.516000] eth0: firmware upload complete
[17179588.516000] ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 19 (level, low) -> IRQ 225
[17179588.516000] eth1: RealTek RTL8139 at 0xe09e0800, 00:0a:e4:55:42:09, IRQ 225
[17179588.516000] eth1:  Identified 8139 chip type 'RTL-8101'
[17179588.520000] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 20 (level, low) -> IRQ 177
[17179588.520000] Yenta: CardBus bridge found at 0000:03:04.0 [17c0:17c0]
[17179588.520000] Yenta: Using CSCINT to route CSC interrupts to PCI
[17179588.520000] Yenta: Routing CardBus interrupts to PCI
[17179588.520000] Yenta TI: socket 0000:03:04.0, mfunc 0x010a1b22, devctl 0x64
[17179588.520000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 217
[17179588.536000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17179588.752000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 177
[17179588.752000] Socket status: 30000006
[17179588.752000] Yenta: Raising subordinate bus# of parent bus (#03) from #03 to #07
[17179588.752000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[17179588.752000] cs: IO port probe 0x3000-0x3fff: clean.
[17179588.752000] pcmcia: parent PCI bridge Memory window: 0xd2000000 - 0xd20fffff
[17179588.752000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x34ffffff
[17179588.756000] ACPI: PCI Interrupt 0000:03:04.1[b] -> GSI 21 (level, low) -> IRQ 185
[17179588.756000] Yenta: CardBus bridge found at 0000:03:04.1 [17c0:17c0]
[17179588.756000] Yenta: Using CSCINT to route CSC interrupts to PCI
[17179588.756000] Yenta: Routing CardBus interrupts to PCI
[17179588.756000] Yenta TI: socket 0000:03:04.1, mfunc 0x010a1b22, devctl 0x64
[17179588.988000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 185
[17179588.988000] Socket status: 30000006
[17179588.988000] Yenta: Raising subordinate bus# of parent bus (#03) from #07 to #0b
[17179588.988000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[17179588.988000] cs: IO port probe 0x3000-0x3fff: clean.
[17179588.988000] pcmcia: parent PCI bridge Memory window: 0xd2000000 - 0xd20fffff
[17179588.988000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x34ffffff
[17179588.996000] NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8776  Mon Oct 16 21:56:04 PDT 2006
[17179589.304000] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[17179589.832000] cs: IO port probe 0x100-0x3af: clean.
[17179589.832000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[17179589.836000] cs: IO port probe 0x820-0x8ff: clean.
[17179589.836000] cs: IO port probe 0xc00-0xcf7: clean.
[17179589.836000] cs: IO port probe 0xa00-0xaff: clean.
[17179589.836000] cs: IO port probe 0x100-0x3af: clean.
[17179589.840000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[17179589.840000] cs: IO port probe 0x820-0x8ff: clean.
[17179589.840000] cs: IO port probe 0xc00-0xcf7: clean.
[17179589.840000] cs: IO port probe 0xa00-0xaff: clean.
[17179590.004000] lp: driver loaded but no devices found
[17179590.056000] SCSI subsystem initialized
[17179590.068000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[17179590.068000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179590.372000] NET: Registered protocol family 17
[17179590.372000] EXT3 FS on hda2, internal journal
[17179590.696000] kjournald starting.  Commit interval 5 seconds
[17179590.704000] EXT3 FS on hda3, internal journal
[17179590.704000] EXT3-fs: mounted filesystem with ordered data mode.
[17179590.748000] NTFS driver 2.1.27 [Flags: R/O MODULE].
[17179590.808000] NTFS volume version 3.1.
[17179592.464000] NET: Registered protocol family 10
[17179592.464000] lo: Disabled Privacy Extensions
[17179592.464000] IPv6 over IPv4 tunneling driver
[17179595.160000] ACPI: AC Adapter [AC] (on-line)
[17179595.192000] ACPI: Battery Slot [BAT0] (battery present)
[17179595.204000] ACPI: Power Button (FF) [PWRF]
[17179595.204000] ACPI: Sleep Button (CM) [SLPB]
[17179595.204000] ACPI: Lid Switch [LID0]
[17179595.204000] ACPI: Power Button (CM) [PWRB]
[17179595.316000] ibm_acpi: ec object not found
[17179595.348000] pcc_acpi: loading...
[17179595.628000] ACPI: Video Device [EVGA] (multi-head: yes  rom: no  post: no)
[17179595.892000] acpi-cpufreq: CPU0 - ACPI performance management activated.
[17179595.892000] acpi-cpufreq: CPU1 - ACPI performance management activated.
[17179599.536000] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[17179599.536000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[17179599.536000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[17179599.888000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179599.888000] apm: disabled - APM is not SMP safe.
[17179601.616000] ttyS1: LSR safety check engaged!
[17179602.884000] eth0: no IPv6 routers present
[17179602.960000] /dev/vmmon[4566]: Module vmmon: registered with major=10 minor=165
[17179602.960000] /dev/vmmon[4566]: Module vmmon: initialized
[17179603.080000] /dev/vmnet: open called by PID 4592 (vmnet-bridge)
[17179603.080000] /dev/vmnet: hub 0 does not exist, allocating memory.
[17179603.080000] /dev/vmnet: port on hub 0 successfully opened
[17179603.080000] bridge-eth0: enabling the bridge
[17179603.080000] bridge-eth0: up
[17179603.080000] bridge-eth0: already up
[17179603.080000] bridge-eth0: attached
[17179603.156000] /dev/vmnet: open called by PID 4606 (vmnet-natd)
[17179603.156000] /dev/vmnet: hub 8 does not exist, allocating memory.
[17179603.156000] /dev/vmnet: port on hub 8 successfully opened
[17179603.312000] Bluetooth: Core ver 2.8
[17179603.312000] NET: Registered protocol family 31
[17179603.312000] Bluetooth: HCI device and connection manager initialized
[17179603.312000] Bluetooth: HCI socket layer initialized
[17179603.360000] Bluetooth: L2CAP ver 2.8
[17179603.360000] Bluetooth: L2CAP socket layer initialized
[17179603.400000] Bluetooth: RFCOMM socket layer initialized
[17179603.400000] Bluetooth: RFCOMM TTY layer initialized
[17179603.400000] Bluetooth: RFCOMM ver 1.7
[17179613.100000] /dev/vmnet: open called by PID 4909 (vmnet-netifup)
[17179613.100000] /dev/vmnet: hub 1 does not exist, allocating memory.
[17179613.100000] /dev/vmnet: port on hub 1 successfully opened
[17179613.124000] /dev/vmnet: open called by PID 4923 (vmnet-netifup)
[17179613.124000] /dev/vmnet: port on hub 8 successfully opened
[17179613.448000] /dev/vmnet: open called by PID 4938 (vmnet-dhcpd)
[17179613.448000] /dev/vmnet: port on hub 8 successfully opened
[17179613.492000] /dev/vmnet: open called by PID 4936 (vmnet-dhcpd)
[17179613.492000] /dev/vmnet: port on hub 1 successfully opened
[17179623.280000] vmnet8: no IPv6 routers present
[17179623.496000] vmnet1: no IPv6 routers present
Hierboven de heb ik de uitkomst gepost van desmeg, voor zover ik weet een log van het opstarten. Hopelijk heb ik de code tags juist gehanteerd. (edit: nee dus, maar nu wel)

Zou iemand hier eens naar willen kijken, met het oog op mijn voortdurende vastlopers? Ik vind Ubuntu echt geweldig en wil liever niet terug naar W******, maar ik kan niet blijven werken met een systeem dat alsmaar bevriest.

Ik heb geen idee hoe ik de mededelingen in dit log zou moeten interpreteren, maar een paar dingetjes vallen mij wel op:

#1 Er is sprake van CPU0 en CPU1, heb ik dan een dual core processor? En zo ja, moet ik daar dan ook nog speciale aktie op ondernemen?

#2 ACPI looking for DSTD ....not found, moet ik daar nog iets mee?

#3 Please report the result to Linux-kernel to fix this permanently, waar gaat deze melding over en is dat erg?

Dat is slechts wat mij zo snel opvalt. Ik zou heel graag willen dat iemand even naar het hele verhaal kijkt of alles OK is.

btw: ik zie tijdens het opstarten steeds meer witte tekst voorbij komen, maar wel wat te snel om te lezen. Ik krijg dus wel de indruk dat het systeem bepaalde klachten heeft over de staat waarin het verkeert. Graag hulp.

Bij voorbaat dank!

Offline Soul-Sing

  • Lid
  • Steunpunt: Nee
Vastlopers in Nautilus
« Reactie #24 Gepost op: 2007/01/25, 09:08:34 »
in de terminal :
Citaat
uname -r
en                  :
Citaat
dmesg | grep CPU#
je kernel bekijken en de eventuele dualcore hardware. :)