Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: hp F380 wil niet printen  (gelezen 1749 keer)

Offline Wierd Kooistra

  • Lid
  • Steunpunt: Nee
hp F380 wil niet printen
« Gepost op: 2011/01/01, 11:52:47 »
Ik heb een probleem om een hp F380 aan het printen te krijgen. Ik gebruik een laptop waarbij ik draadloos internet gebruik. De printer wordt gevonden en installatie is ook geen probleem. De printer maakt wel geluiden maar er komt niets uit. Ik heb het ook geprobeerd met de printer geinstallerd via een kabeltje op een usb poort met het zelfde resultaat. Iemand enig idee wat de oorzaak kan zijn. In windows 7 werkt deze all in one printer echter wel.

Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: hp F380 wil niet printen
« Reactie #1 Gepost op: 2011/01/01, 12:29:53 »
Heb je HPLIP en HPLIP-GUI al geinstalleerd via het Ubuntu Software Centrum, Synaptic of de terminal?
En heb je cups ook geinstalleerd? Na installatie terug te vinden door in de adresbalk van je browser te typen http://localhost:631/ hier kan je ook het een en ander instellen. Gebruik je de printer in een Windows/Ubuntu netwerk, zal je de configuratie van Samba in moeten stellen.
In der Beschränkung zeigt sich der Meister.

Offline Wierd Kooistra

  • Lid
  • Steunpunt: Nee
Re: hp F380 wil niet printen
« Reactie #2 Gepost op: 2011/01/01, 15:29:33 »
Ik heb alles ingesteld zoals je vermeldt. Ik kan nu wel via een usb draadje printen. Draadloos lukt me nog steeds niet ondanks dat ik de print heb ingesteld via samba.

Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: hp F380 wil niet printen
« Reactie #3 Gepost op: 2011/01/01, 18:16:11 »
Kan je de configuratie file van Samba hier plaatsen? En heb je de printer ook draadloos op het netwerk?

Kan je ook dit installeren hplip-dbg  Als dit geïnstalleerd is kan je dit commando geven in de terminal hp-check -t dan krijg je deze output met eventuele errors:
gijs@gijs-desktop:~$ hp-check -t

HP Linux Imaging and Printing System (ver. 3.10.2)
Dependency/Version Check Utility ver. 14.3

Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.

Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.                                    
2. Run-time check mode (-r or --run): Use this mode to determine if a distro    
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball  
has the proper dependencies installed to successfully run.                      
3. Both compile- and run-time check mode (-b or --both) (Default): This mode    
will check both of the above cases (both compile- and run-time dependencies).  

Saving output in log file: hp-check.log

Initializing. Please wait...
 
---------------
| SYSTEM INFO |
---------------

Basic system information:
Linux gijs-desktop 2.6.32-27-generic #49-Ubuntu SMP Thu Dec 2 00:51:09 UTC 2010 x86_64 GNU/Linux

Distribution:
ubuntu 10.04

Checking Python version...
OK, version 2.6.5 installed

Checking PyQt 4.x version...
OK, version 4.7.2 installed.

Checking for CUPS...
Status: taakplanner is actief
Version: 1.4.3
error_log is set to level: warn

Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0


------------------------------------
| COMPILE AND RUNTIME DEPENDENCIES |
------------------------------------

note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).

Checking for dependency: CUPS - Common Unix Printing System...
OK, found.

Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.

Checking for dependency: CUPS image - CUPS image development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libcupsimage2-dev

Checking for dependency: DBus - Message bus system...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libdbus-1-dev

Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.

Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.

Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.

Checking for dependency: libjpeg - JPEG library...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libjpeg62-dev

Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libsnmp-dev

Checking for dependency: libpthread - POSIX threads library...
OK, found.

Checking for dependency: libtool - Library building support services...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libtool

Checking for dependency: libusb - USB library...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libusb-dev

Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.

Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.

Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.

Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.

Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.

Checking for dependency: Python devel - Python development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes python-dev

Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.

Checking for dependency: Python XML libraries...
OK, found.

Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.

Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.

Checking for dependency: Reportlab - PDF library for Python...
OK, found.

Checking for dependency: SANE - Scanning library...
OK, found.

Checking for dependency: SANE - Scanning library development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.
To install this dependency, execute this command:
sudo aptitude install --assume-yes libsane-dev

Checking for dependency: scanimage - Shell scanning program...
OK, found.

Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.


----------------------
| HPLIP INSTALLATION |
----------------------


Currently installed HPLIP version...
HPLIP 3.10.2 currently installed in '/usr/share/hplip'.

Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf.  Generated from hplip.conf.in by configure.

[hplip]
version=3.10.2

[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/hplip/HP
ppdbase=/usr/share/ppd/hplip
doc=/usr/share/doc/hplip-doc/HTML
icon=no
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv

# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=yes
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=yes
foomatic-drv-install=yes
foomatic-ppd-install=yes
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.10.2rc1.9
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=yes
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no


Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.

[plugin]
installed=0
eula=0



Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Photosmart_8200_series?serial=MY5CM3X2S704KJ"

[commands]
scan = /usr/bin/xsane -V %SANE_URI%

[installation]
version = 3.10.2rc1.9
date_time = 01-01-11 18:21:18

[settings]
systray_messages = 0
systray_visible = 0

[fax]
email_address =
voice_phone =

[refresh]
rate = 30
enable = false
type = 1

[polling]
enable = false
device_list =
interval = 5



--------------------------
| DISCOVERED USB DEVICES |
--------------------------

  Device URI                        Model                    
  --------------------------------  -------------------------
  hp:/usb/Photosmart_8200_series?s  HP Photosmart 8200 series
  erial=MY5CM3X2S704KJ                                      

---------------------------------
| INSTALLED CUPS PRINTER QUEUES |
---------------------------------

 
Photosmart-8200-series
----------------------
Type: Printer
Device URI: hp:/usb/Photosmart_8200_series?serial=MY5CM3X2S704KJ
PPD: /etc/cups/ppd/Photosmart-8200-series.ppd
PPD Description: HP Photosmart 8200 Series hpijs, 3.10.2
Printer status: printer Photosmart-8200-series is niet in gebruik.  ingeschakeld sinds vr 24 dec 2010 20:27:41 CET
Communication status: Good


----------------------
| SANE CONFIGURATION |
----------------------

'hpaio' in '/etc/sane.d/dll.conf'...
'hpaio' in '/etc/sane.d/dll.d/hplip'...
OK, found. SANE backend 'hpaio' is properly set up.

Checking output of 'scanimage -L'...
 
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).


---------------------
| PYTHON EXTENSIONS |
---------------------

Checking 'cupsext' CUPS extension...
OK, found.

Checking 'pcardext' Photocard extension...
OK, found.

Checking 'hpmudext' I/O extension...
OK, found.

Checking 'scanext' SANE scanning extension...
OK, found.


 
-----------------
| USB I/O SETUP |
-----------------

Checking for permissions of USB attached printers...

HP Device 0xc202 at 004:004:
    Device URI: hp:/usb/Photosmart_8200_series?serial=MY5CM3X2S704KJ
    Device node: /dev/bus/usb/004/004
    Mode: 0664

---------------
| USER GROUPS |
---------------

gijs adm dialout fax cdrom floppy tape audio dip video plugdev fuse lpadmin netdev admin sambashare vboxusers usb

error: User needs to be member of group 'lp' to enable print, scan & fax.
User member of group 'lpadmin'.

-----------
| SUMMARY |
-----------

error: 8 errors and/or warnings.

Summary of needed commands to run to satisfy missing dependencies:
sudo aptitude install --assume-yes libcupsimage2-dev
sudo aptitude install --assume-yes libdbus-1-dev
sudo aptitude install --assume-yes libjpeg62-dev
sudo aptitude install --assume-yes libsnmp-dev
sudo aptitude install --assume-yes libtool
sudo aptitude install --assume-yes libusb-dev
sudo aptitude install --assume-yes python-dev
sudo aptitude install --assume-yes libsane-dev

Please refer to the installation instructions at:
http://hplip.sourceforge.net/install/index.html


Done.
gijs@gijs-desktop:~$
En nainstallatie van de 8 pakketjes genoemd in de error melding:
gijs@gijs-desktop:~$ hp-check -t

HP Linux Imaging and Printing System (ver. 3.10.2)
Dependency/Version Check Utility ver. 14.3

Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.

Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.                                   
2. Run-time check mode (-r or --run): Use this mode to determine if a distro   
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball   
has the proper dependencies installed to successfully run.                     
3. Both compile- and run-time check mode (-b or --both) (Default): This mode   
will check both of the above cases (both compile- and run-time dependencies).   

Saving output in log file: hp-check.log

Initializing. Please wait...
 
---------------
| SYSTEM INFO |
---------------

Basic system information:
Linux gijs-desktop 2.6.32-27-generic #49-Ubuntu SMP Thu Dec 2 00:51:09 UTC 2010 x86_64 GNU/Linux

Distribution:
ubuntu 10.04

Checking Python version...
OK, version 2.6.5 installed

Checking PyQt 4.x version...
OK, version 4.7.2 installed.

Checking for CUPS...
Status: taakplanner is actief
Version: 1.4.3
error_log is set to level: warn

Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0


------------------------------------
| COMPILE AND RUNTIME DEPENDENCIES |
------------------------------------

note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).

Checking for dependency: CUPS - Common Unix Printing System...
OK, found.

Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.

Checking for dependency: CUPS image - CUPS image development files...
OK, found.

Checking for dependency: DBus - Message bus system...
OK, found.

Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.

Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.

Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.

Checking for dependency: libjpeg - JPEG library...
OK, found.

Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
OK, found.

Checking for dependency: libpthread - POSIX threads library...
OK, found.

Checking for dependency: libtool - Library building support services...
OK, found.

Checking for dependency: libusb - USB library...
OK, found.

Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.

Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.

Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.

Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.

Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.

Checking for dependency: Python devel - Python development files...
OK, found.

Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.

Checking for dependency: Python XML libraries...
OK, found.

Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.

Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.

Checking for dependency: Reportlab - PDF library for Python...
OK, found.

Checking for dependency: SANE - Scanning library...
OK, found.

Checking for dependency: SANE - Scanning library development files...
OK, found.

Checking for dependency: scanimage - Shell scanning program...
OK, found.

Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.


----------------------
| HPLIP INSTALLATION |
----------------------


Currently installed HPLIP version...
HPLIP 3.10.2 currently installed in '/usr/share/hplip'.

Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf.  Generated from hplip.conf.in by configure.

[hplip]
version=3.10.2

[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/hplip/HP
ppdbase=/usr/share/ppd/hplip
doc=/usr/share/doc/hplip-doc/HTML
icon=no
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv

# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=yes
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=yes
foomatic-drv-install=yes
foomatic-ppd-install=yes
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.10.2rc1.9
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=yes
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no


Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.

[plugin]
installed=0
eula=0



Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Photosmart_8200_series?serial=MY5CM3X2S704KJ"

[commands]
scan = /usr/bin/xsane -V %SANE_URI%

[installation]
version = 3.10.2rc1.9
date_time = 01-01-11 18:31:14

[settings]
systray_messages = 0
systray_visible = 0

[fax]
email_address =
voice_phone =

[refresh]
rate = 30
enable = false
type = 1

[polling]
enable = false
device_list =
interval = 5



--------------------------
| DISCOVERED USB DEVICES |
--------------------------

  Device URI                        Model                   
  --------------------------------  -------------------------
  hp:/usb/Photosmart_8200_series?s  HP Photosmart 8200 series
  erial=MY5CM3X2S704KJ                                       

---------------------------------
| INSTALLED CUPS PRINTER QUEUES |
---------------------------------

 
Photosmart-8200-series
----------------------
Type: Printer
Device URI: hp:/usb/Photosmart_8200_series?serial=MY5CM3X2S704KJ
PPD: /etc/cups/ppd/Photosmart-8200-series.ppd
PPD Description: HP Photosmart 8200 Series hpijs, 3.10.2
Printer status: printer Photosmart-8200-series is niet in gebruik.  ingeschakeld sinds vr 24 dec 2010 20:27:41 CET
Communication status: Good


----------------------
| SANE CONFIGURATION |
----------------------

'hpaio' in '/etc/sane.d/dll.conf'...
'hpaio' in '/etc/sane.d/dll.d/hplip'...
OK, found. SANE backend 'hpaio' is properly set up.

Checking output of 'scanimage -L'...
 
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).


---------------------
| PYTHON EXTENSIONS |
---------------------

Checking 'cupsext' CUPS extension...
OK, found.

Checking 'pcardext' Photocard extension...
OK, found.

Checking 'hpmudext' I/O extension...
OK, found.

Checking 'scanext' SANE scanning extension...
OK, found.


 
-----------------
| USB I/O SETUP |
-----------------

Checking for permissions of USB attached printers...

HP Device 0xc202 at 004:004:
    Device URI: hp:/usb/Photosmart_8200_series?serial=MY5CM3X2S704KJ
    Device node: /dev/bus/usb/004/004
    Mode: 0664

---------------
| USER GROUPS |
---------------

gijs adm dialout fax cdrom floppy tape audio dip video plugdev fuse lpadmin netdev admin sambashare vboxusers usb

error: User needs to be member of group 'lp' to enable print, scan & fax.
User member of group 'lpadmin'.

-----------
| SUMMARY |
-----------

No errors or warnings.

Done.
gijs@gijs-desktop:~$
Geen fouten meer, samba kan ik zelf nu niet testen, omdat mijn zoon niet achter zijn Windows PC's weg wilt gaan. >:(
« Laatst bewerkt op: 2011/01/01, 18:34:53 door Gijsbert »
In der Beschränkung zeigt sich der Meister.

Offline Wierd Kooistra

  • Lid
  • Steunpunt: Nee
Re: hp F380 wil niet printen
« Reactie #4 Gepost op: 2011/01/01, 20:33:23 »
Hier heb het commando in de terminal:



HP Linux Imaging and Printing System (ver. 3.10.6)
Dependency/Version Check Utility ver. 14.3

Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.

Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.                                    
2. Run-time check mode (-r or --run): Use this mode to determine if a distro    
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball  
has the proper dependencies installed to successfully run.                      
3. Both compile- and run-time check mode (-b or --both) (Default): This mode    
will check both of the above cases (both compile- and run-time dependencies).  

Saving output in log file: hp-check.log

Initializing. Please wait...
\Gtk-Message: (for origin information, set GTK_DEBUG): failed to retrieve property `gtk-enable-event-sounds' of type `gboolean' from rc file value "((GString*) 0xa0e0340)" of type `gboolean'
Gtk-Message: (for origin information, set GTK_DEBUG): failed to retrieve property `gtk-enable-input-feedback-sounds' of type `gboolean' from rc file value "((GString*) 0xa176a30)" of type `gboolean'
Gtk-Message: (for origin information, set GTK_DEBUG): failed to retrieve property `gtk-button-images' of type `gboolean' from rc file value "((GString*) 0xa173e50)" of type `gboolean'
 
---------------
| SYSTEM INFO |
---------------

Basic system information:
Linux wierd-hp-Compaq-nc6000-DD522AV 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 01:41:57 UTC 2010 i686 GNU/Linux

Distribution:
ubuntu 10.10

Checking Python version...
OK, version 2.6.6 installed

Checking PyQt 4.x version...
OK, version 4.7.4 installed.

Checking for CUPS...
Status: taakplanner is actief
warning: Version: (cups-config) Not available. Unable to determine installed version of CUPS.)
error_log is set to level: warn

Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0


------------------------------------
| COMPILE AND RUNTIME DEPENDENCIES |
------------------------------------

note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).

Checking for dependency: CUPS - Common Unix Printing System...
OK, found.

Checking for dependency: CUPS DDK - CUPS driver development kit...
warning: NOT FOUND! This is an OPTIONAL/RUNTIME ONLY dependency. Some HPLIP functionality may not function properly.

Checking for dependency: CUPS devel- Common Unix Printing System development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: CUPS image - CUPS image development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: DBus - Message bus system...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: gcc - GNU Project C and C++ Compiler...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.

Checking for dependency: libcrypto - OpenSSL cryptographic library...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: libjpeg - JPEG library...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: libpthread - POSIX threads library...
OK, found.

Checking for dependency: libtool - Library building support services...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: libusb - USB library...
error: NOT FOUND! This is a REQUIRED dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.

Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.

Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.

Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.

Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.

Checking for dependency: Python devel - Python development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.

Checking for dependency: Python XML libraries...
OK, found.

Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.

Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.

Checking for dependency: Reportlab - PDF library for Python...
OK, found.

Checking for dependency: SANE - Scanning library...
OK, found.

Checking for dependency: SANE - Scanning library development files...
error: NOT FOUND! This is a REQUIRED/COMPILE TIME ONLY dependency. Please make sure that this dependency is installed before installing or running HPLIP.

Checking for dependency: scanimage - Shell scanning program...
OK, found.

Checking for dependency: xsane - Graphical scanner frontend for SANE...
warning: NOT FOUND! This is an OPTIONAL/RUNTIME ONLY dependency. Some HPLIP functionality may not function properly.


----------------------
| HPLIP INSTALLATION |
----------------------


Currently installed HPLIP version...
HPLIP 3.10.6 currently installed in '/usr/share/hplip'.

Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf.  Generated from hplip.conf.in by configure.

[hplip]
version=3.10.6

[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/hplip/HP
ppdbase=/usr/share/ppd/hplip
doc=/usr/share/doc/hplip-doc/HTML
icon=no
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv

# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=yes
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=yes
foomatic-drv-install=yes
foomatic-ppd-install=yes
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.10.6.15
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=yes
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no


Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.

[plugin]
installed=0
eula=0



Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Deskjet_F300_series?serial=CN66RGK4CV04KH"

[commands]
scan = /usr/bin/simple-scan %SANE_URI%

[installation]
date_time = 01-01-11 20:30:33
version = 3.10.6.15

[settings]
systray_messages = 0
systray_visible = 0

[fax]
email_address =
voice_phone =

[refresh]
rate = 30
enable = false
type = 1

[polling]
enable = false
device_list =
interval = 5



--------------------------
| DISCOVERED USB DEVICES |
--------------------------

No devices found.

---------------------------------
| INSTALLED CUPS PRINTER QUEUES |
---------------------------------

 
HP-Deskjet-f300
---------------
Type: Unknown
Device URI: smb://WORKGROUP/WIERD-PC/HP%20Deskjet%20F300%20Series
PPD: /etc/cups/ppd/HP-Deskjet-f300.ppd
PPD Description: HP Deskjet f300 Series hpijs, 3.10.6
Printer status: printer HP-Deskjet-f300 is niet in gebruik.  ingeschakeld sinds za 01 jan 2011 15:25:40 CET
warning: Printer is not HPLIP installed. Printers must use the hp: or hpfax: CUPS backend to function in HPLIP.


----------------------
| SANE CONFIGURATION |
----------------------

'hpaio' in '/etc/sane.d/dll.conf'...
'hpaio' in '/etc/sane.d/dll.d/hplip'...
OK, found. SANE backend 'hpaio' is properly set up.

Checking output of 'scanimage -L'...
 
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).


---------------------
| PYTHON EXTENSIONS |
---------------------

Checking 'cupsext' CUPS extension...
OK, found.

Checking 'pcardext' Photocard extension...
OK, found.

Checking 'hpmudext' I/O extension...
OK, found.

Checking 'scanext' SANE scanning extension...
OK, found.


 
---------------
| USER GROUPS |
---------------

wierd adm dialout cdrom plugdev lpadmin admin sambashare

error: User needs to be member of group 'lp' to enable print, scan & fax.
User member of group 'lpadmin'.

-----------
| SUMMARY |
-----------

error: 14 errors and/or warnings.

Please refer to the installation instructions at:
http://hplip.sourceforge.net/install/index.html

Moderator edit: Code-tags toegevoegd
« Laatst bewerkt op: 2011/01/01, 22:21:58 door Vistaus »

Offline Wierd Kooistra

  • Lid
  • Steunpunt: Nee
Re: hp F380 wil niet printen
« Reactie #5 Gepost op: 2011/01/01, 20:36:10 »
Ik weet niet hoe je de samba file te voorschijn haalt? Is hier een commando voor?

Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: hp F380 wil niet printen
« Reactie #6 Gepost op: 2011/01/01, 22:19:14 »
Die kan je zo tevoorschijn halen met de terminal sudo gedit /etc/samba/smb.conf
Of je typt in de adresbalk van je browser http://localhost:901/   Dan krijg je SWAT te zien de grafischeschil voor de Samba configuratie.
In der Beschränkung zeigt sich der Meister.

Offline Wierd Kooistra

  • Lid
  • Steunpunt: Nee
Re: hp F380 wil niet printen
« Reactie #7 Gepost op: 2011/01/02, 12:34:44 »
Hier mijn samba configuratie.
#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
#  - When such options are commented with ";", the proposed setting
#    differs from the default Samba behaviour
#  - When commented with "#", the proposed setting is the default
#    behaviour of Samba but the option is considered important
#    enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.
# A well-established practice is to name the original file
# "smb.conf.master" and create the "real" config file with
# testparm -s smb.conf.master >smb.conf
# This minimizes the size of the really used smb.conf file
# which, according to the Samba Team, impacts performance
# However, use this with caution if your smb.conf file contains nested
# "include" statements. See Debian bug #483187 for a case
# where using a master file is not a good idea.
#

#======================= Global Settings =======================

[global]

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
   workgroup = WORKGROUP

# server string is the equivalent of the NT Description field
   server string = %h server (Samba, Ubuntu)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
#   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
   dns proxy = no

# What naming service and in what order should we use to resolve host names
# to IP addresses
;   name resolve order = lmhosts host wins bcast

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
   log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
   max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
#   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
   syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
   panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# "security = user" is always a good idea. This will require a Unix account
# in this server for every user accessing the server. See
# /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html
# in the samba-doc package for details.
#   security = user

# You may wish to use password encryption.  See the section on
# 'encrypt passwords' in the smb.conf(5) manpage before enabling.
   encrypt passwords = true

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using. 
   passdb backend = tdbsam

   obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
   unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
   passwd program = /usr/bin/passwd %u
   passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
   pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
   map to guest = bad user

########## Domains ###########

# Is this machine able to authenticate users. Both PDC and BDC
# must have this setting enabled. If you are the BDC you must
# change the 'domain master' setting to no
#
;   domain logons = yes
#
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of the user's profile directory
# from the client point of view)
# The following required a [profiles] share to be setup on the
# samba server (see below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
#   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
#   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the
# SAMR RPC pipe. 
# The following assumes a "machines" group exists on the system
; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe. 
; add group script = /usr/sbin/addgroup --force-badname %g

########## Printing ##########

# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
#   load printers = yes

# lpr(ng) printing. You may wish to override the location of the
# printcap file
;   printing = bsd
;   printcap name = /etc/printcap

# CUPS printing.  See also the cupsaddsmb(8) manpage in the
# cupsys-client package.
;   printing = cups
;   printcap name = cups

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Most people will find that this option gives better performance.
# See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html
# for details
# You may want to add the following on a Linux system:
#         SO_RCVBUF=8192 SO_SNDBUF=8192
#   socket options = TCP_NODELAY

# The following parameter is useful only if you have the linpopup package
# installed. The samba maintainer and the linpopup maintainer are
# working to ease installation and configuration of linpopup and samba.
;   message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' &

# Domain Master specifies Samba to be the Domain Master Browser. If this
# machine will be configured as a BDC (a secondary logon server), you
# must set this to 'no'; otherwise, the default behavior is recommended.
#   domain master = auto

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash

# The following was the default behaviour in sarge,
# but samba upstream reverted the default because it might induce
# performance issues in large organizations.
# See Debian bug #368251 for some of the consequences of *not*
# having this setting and smb.conf(5) for details.
;   winbind enum groups = yes
;   winbind enum users = yes

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
;   usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
   usershare allow guests = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each
# user's home director as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
;   read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server. Un-comment the following parameter
# to make sure that only "username" can connect to \\server\username
# The following parameter makes sure that only "username" can connect
#
# This might need tweaking when using external authentication schemes
;   valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   read only = yes
;   share modes = no

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

[printers]
   comment = All Printers
   browseable = no
   path = /var/spool/samba
   printable = yes
   guest ok = no
   read only = yes
   create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
   comment = Printer Drivers
   path = /var/lib/samba/printers
   browseable = yes
   read only = yes
   guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
;   write list = root, @lpadmin

# A sample share for sharing your CD-ROM with others.
;[cdrom]
;   comment = Samba server's CD-ROM
;   read only = yes
;   locking = no
;   path = /cdrom
;   guest ok = yes

# The next two parameters show how to auto-mount a CD-ROM when the
#   cdrom share is accesed. For this to work /etc/fstab must contain
#   an entry like this:
#
#       /dev/scd0   /cdrom  iso9660 defaults,noauto,ro,user   0 0
#
# The CD-ROM gets unmounted automatically after the connection to the
#
# If you don't want to use auto-mounting/unmounting make sure the CD
#   is mounted on /cdrom
#
;   preexec = /bin/mount /cdrom
;   postexec = /bin/umount /cdrom

Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: hp F380 wil niet printen
« Reactie #8 Gepost op: 2011/01/02, 13:17:19 »
Om dit gedeelte gaat het:
# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
   comment = Printer Drivers
   path = /var/lib/samba/printers
   browseable = yes
   read only = yes
   guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
;   write list = root, @lpadmin
Ben jij en zijn eventueel andere gebruikers lid van de groep lpadmin? De root zou in ieder geval moeten kunnen printen, heb je dit al geprobeerd?
In der Beschränkung zeigt sich der Meister.

Offline Wierd Kooistra

  • Lid
  • Steunpunt: Nee
Re: hp F380 wil niet printen
« Reactie #9 Gepost op: 2011/01/02, 20:52:55 »
Ik heb maar één gebruiker en dat ben ik zelf. Ik ben lid als gebruiker van genoemde. Er komen wel geluiden uit de printer maar helaas er wordt niets geprint.

Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: hp F380 wil niet printen
« Reactie #10 Gepost op: 2011/01/02, 22:19:07 »
In dit stukje:
comment = All Printers
   browseable = no
   path = /var/spool/samba
   printable = yes
   guest ok = no     <----------------- Zet i.p.v. no hier yes
   read only = yes
   create mask = 0700
In der Beschränkung zeigt sich der Meister.