Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: sata dvd brander samsung branden gaat niet  (gelezen 570 keer)

xubuntunoob

  • Gast
sata dvd brander samsung branden gaat niet
« Gepost op: 2010/05/19, 12:33:52 »
Hey

Ik heb een SATA samsung dvdbrander  nu zit ik met het volgende probleem wissen van cdrws  lukt met gnomebaker
Maar branden van data op een cd-r , cd-rw niet.
dvds lezen gaat wissen en branden niet.  Kent iemand dit probleem?  

Nerolinux 4 (trail) faalt bij wissen en schrijven.

Dit is in geen geval een hardware fout want onder win xp (helaas nodig voor domdom updates) werkt de brander perfect.
Er zijn ook al meerdere schijvjes gebruikt

Dit is de output log van gnomebaker.

wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.9
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   :
Vendor_info    : 'TSSTcorp'
Identification : 'CDDVDW SH-S223Q '
Revision       : 'SB03'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0017 (Reserved/Unknown)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1962752 = 1916 KB
FIFO size      : 12582912 = 12288 KB
Speed set to 1764 KB/s

WARNING: found a microscopic small track size (442368 bytes).
         Do you really want to write this image? Press Ctrl-C to abort...

  24 seconds.  23 seconds.  22 seconds.  21 seconds.  20 seconds.  19 seconds.  18 seconds.  17 seconds.  16 seconds.  15 seconds.  14 seconds.  13 seconds.  12 seconds.  11 seconds.  10 seconds.   9 seconds.   8 seconds.   7 seconds.   6 seconds.   5 seconds.   4 seconds.   3 seconds.   2 seconds.   1 seconds.   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 11700
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 2D B4 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 02 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x02 (end-of-partition/medium detected) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 50.738s timeout 40s
wodim: A write error occured.
wodim: Please properly read the error message above.

write track data: error after 0 bytes
Writing  time:   66.189s
Average write speed   0.1x.
Fixating...
Fixating time:   18.359s
BURN-Free was never needed.
wodim: fifo had 7 puts and 1 gets.
wodim: fifo was 0 times empty and 0 times full, min fill was 100%.


raakt iemand hier wijs uit?
« Laatst bewerkt op: 2010/05/19, 12:35:35 door Wanda »