Nieuws:

We zijn er weer.

Na lange tijd van afwezigheid zijn we er weer  :laugh:
We hebben alle wachtwoorden gereset, je oude wachtwoord werkt niet meer.Je moet via het "wachtwoord vergeten"-linkje je wachtwoord resetten. Je krijgt hiervoor een mailtje op het adres dat je bij ons geregistreerd hebt.

De komende tijd zijn we nog druk bezig om de rest van de site op te bouwen, dus het kan zijn dat sommige onderdelen (tijdelijk) niet werken.

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: Sweex netwerkkaart (RTL8139) werkt niet.  (gelezen 6770 keer)

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Gepost op: 2006/11/02, 13:17:46 »
Ik ben al een tijdje aan de gang om een Sweex netwerkkaart aan de praat te krijgen.
Mijn hardware is een ASUS P5VDC-MX met onboard een netwerkkaart.
Deze heb ik in gebruik, en werkt vlekkeloos. Tijdens de installatie had ik ook (al) de SWEEX-lancard erin zitten.
Volgens de bijgeleverde doc kan deze aangestuurd worden onder Linux met RTL8139. Maar dit werkt niet.
lspci geeft de volgende info:

0000:00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
0000:00:00.1 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
0000:00:00.2 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
0000:00:00.3 Host bridge: VIA Technologies, Inc. PT890 Host Bridge
0000:00:00.4 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
0000:00:00.7 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VT8251 AHCI/SATA 4-Port Controller
0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 07)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90)
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 90)
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 90)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8251 PCI to ISA Bridge
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 70)
0000:00:11.7 Host bridge: VIA Technologies, Inc. VT8251 Ultra VLINK Controller
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c)
0000:00:13.0 PCI bridge: VIA Technologies, Inc. VT8251 Host Bridge
0000:00:13.1 PCI bridge: VIA Technologies, Inc. VT8251 PCI to PCI Bridge
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. UniChrome Pro IGP (rev 01)
0000:02:00.0 PCI bridge: VIA Technologies, Inc. VT8251 PCIE Root Port
0000:02:00.1 PCI bridge: VIA Technologies, Inc. VT8251 PCIE Root Port
0000:02:01.0 Audio device: VIA Technologies, Inc. VIA High Definition Audio Controller

Maar verder geen info over de realtek.
De dmesg geeft volgende info:

[17179569.184000] Linux version 2.6.15-27-386 (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Sat Sep 16 01:51:59 UTC 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000003bfb0000 (usable)
[17179569.184000]  BIOS-e820: 000000003bfb0000 - 000000003bfbe000 (ACPI data)
[17179569.184000]  BIOS-e820: 000000003bfbe000 - 000000003bfe0000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 000000003bfe0000 - 000000003c000000 (reserved)
[17179569.184000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[17179569.184000] 63MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000ff780
[17179569.184000] On node 0 totalpages: 245680
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000]   Normal zone: 225280 pages, LIFO batch:31
[17179569.184000]   HighMem zone: 16304 pages, LIFO batch:3
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 ACPIAM                                ) @ 0x000fa8a0
[17179569.184000] ACPI: RSDT (v001 A M I  OEMRSDT  0x06000606 MSFT 0x00000097) @ 0x3bfb0000
[17179569.184000] ACPI: FADT (v002 A M I  OEMFACP  0x06000606 MSFT 0x00000097) @ 0x3bfb0200
[17179569.184000] ACPI: MADT (v001 A M I  OEMAPIC  0x06000606 MSFT 0x00000097) @ 0x3bfb0390
[17179569.184000] ACPI: MCFG (v001 A M I  OEMMCFG  0x06000606 MSFT 0x00000097) @ 0x3bfb03f0
[17179569.184000] ACPI: OEMB (v001 A M I  AMI_OEM  0x06000606 MSFT 0x00000097) @ 0x3bfbe040
[17179569.184000] ACPI: DSDT (v001  A0403 A0403601 0x00000601 INTL 0x02002026) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x808
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:4 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[17179569.184000] Processor #1 15:4 APIC version 20
[17179569.184000] WARNING: NR_CPUS limit of 1 reached.  Processor ignored.
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 40000000 (gap: 3c000000:a4000000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/md0 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[17179569.184000] Detected 2660.585 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179572.496000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179572.496000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179572.520000] Memory: 963632k/982720k available (1976k kernel code, 18420k reserved, 606k data, 288k init, 65216k highmem)
[17179572.520000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179572.600000] Calibrating delay using timer specific routine.. 5325.37 BogoMIPS (lpj=10650755)
[17179572.600000] Security Framework v1.0.0 initialized
[17179572.600000] SELinux:  Disabled at boot.
[17179572.600000] Mount-cache hash table entries: 512
[17179572.600000] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
[17179572.600000] CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
[17179572.600000] monitor/mwait feature present.
[17179572.600000] using mwait in idle threads.
[17179572.600000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[17179572.600000] CPU: L2 cache: 1024K
[17179572.600000] CPU: After all inits, caps: bfebfbff 20000000 00000000 00000080 0000651d 00000000 00000001
[17179572.600000] mtrr: v2.0 (20020519)
[17179572.600000] CPU: Intel(R) Pentium(R) D  CPU 2.66GHz stepping 07
[17179572.600000] Enabling fast FPU save and restore... done.
[17179572.600000] Enabling unmasked SIMD FPU exception support... done.
[17179572.600000] Checking 'hlt' instruction... OK.
[17179572.616000] checking if image is initramfs... it is
[17179573.192000] Freeing initrd memory: 6616k freed
[17179573.204000] ACPI: Looking for DSDT ... not found!
[17179573.208000] ENABLING IO-APIC IRQs
[17179573.208000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179573.356000] NET: Registered protocol family 16
[17179573.356000] EISA bus registered
[17179573.356000] ACPI: bus type pci registered
[17179573.356000] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[17179573.356000] PCI: Using MMCONFIG
[17179573.356000] ACPI: Subsystem revision 20051216
[17179573.360000] ACPI: Interpreter enabled
[17179573.360000] ACPI: Using IOAPIC for interrupt routing
[17179573.364000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179573.364000] PCI: Probing PCI hardware (bus 00)
[17179573.368000] Boot video device is 0000:01:00.0
[17179573.372000] PCI: Transparent bridge - 0000:00:13.1
[17179573.372000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179573.396000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[17179573.404000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[17179573.408000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P8._PRT]
[17179573.408000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7.P7P9._PRT]
[17179573.408000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PB._PRT]
[17179573.412000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[17179573.412000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[17179573.412000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[17179573.412000] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[17179573.412000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179573.412000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179573.412000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179573.412000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179573.412000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179573.412000] pnp: PnP ACPI init
[17179573.424000] pnp: PnP ACPI: found 15 devices
[17179573.424000] PnPBIOS: Disabled by ACPI PNP
[17179573.424000] PCI: Using ACPI for IRQ routing
[17179573.424000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179573.440000] PCI: Device 0000:02:01.0 not found by BIOS
[17179573.440000] pnp: 00:0c: ioport range 0xc00-0xc0f has been reserved
[17179573.440000] pnp: 00:0c: ioport range 0xd00-0xd0f has been reserved
[17179573.440000] pnp: 00:0c: ioport range 0xa20-0xa2f has been reserved
[17179573.440000] pnp: 00:0c: ioport range 0xa30-0xa3f has been reserved
[17179573.444000] PCI: Bridge: 0000:00:01.0
[17179573.444000]   IO window: disabled.
[17179573.444000]   MEM window: fc900000-fe9fffff
[17179573.444000]   PREFETCH window: d7f00000-dfefffff
[17179573.444000] PCI: Bridge: 0000:02:00.0
[17179573.444000]   IO window: disabled.
[17179573.444000]   MEM window: disabled.
[17179573.444000]   PREFETCH window: disabled.
[17179573.444000] PCI: Bridge: 0000:02:00.1
[17179573.444000]   IO window: disabled.
[17179573.444000]   MEM window: disabled.
[17179573.444000]   PREFETCH window: disabled.
[17179573.444000] PCI: Bridge: 0000:00:13.0
[17179573.444000]   IO window: disabled.
[17179573.444000]   MEM window: 40000000-400fffff
[17179573.444000]   PREFETCH window: disabled.
[17179573.444000] PCI: Bridge: 0000:00:13.1
[17179573.444000]   IO window: c000-cfff
[17179573.444000]   MEM window: fea00000-feafffff
[17179573.444000]   PREFETCH window: disabled.
[17179573.444000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179573.444000] PCI: Enabling device 0000:00:13.0 (0104 -> 0106)
[17179573.444000] PCI: Setting latency timer of device 0000:00:13.0 to 64
[17179573.444000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[17179573.444000] PCI: Setting latency timer of device 0000:02:00.1 to 64
[17179573.444000] PCI: Setting latency timer of device 0000:00:13.1 to 64
[17179573.444000] audit: initializing netlink socket (disabled)
[17179573.444000] audit(1162390119.444:1): initialized
[17179573.444000] highmem bounce pool size: 64 pages
[17179573.444000] VFS: Disk quotas dquot_6.5.1
[17179573.444000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179573.444000] Initializing Cryptographic API
[17179573.444000] io scheduler noop registered
[17179573.444000] io scheduler anticipatory registered
[17179573.444000] io scheduler deadline registered
[17179573.444000] io scheduler cfq registered
[17179573.444000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[17179573.444000] pcie_portdrv_probe->Dev[287c:1106] has invalid IRQ. Check vendor BIOS
[17179573.444000] assign_interrupt_mode Found MSI capability
[17179573.444000] Allocate Port Service[pcie00]
[17179573.444000] Allocate Port Service[pcie01]
[17179573.444000] Allocate Port Service[pcie03]
[17179573.444000] PCI: Setting latency timer of device 0000:02:00.1 to 64
[17179573.444000] pcie_portdrv_probe->Dev[287d:1106] has invalid IRQ. Check vendor BIOS
[17179573.444000] assign_interrupt_mode Found MSI capability
[17179573.444000] Allocate Port Service[pcie00]
[17179573.444000] Allocate Port Service[pcie01]
[17179573.444000] Allocate Port Service[pcie03]
[17179573.444000] isapnp: Scanning for PnP cards...
[17179573.796000] isapnp: No Plug & Play device found
[17179573.812000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[17179573.812000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179573.812000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179573.816000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[17179573.816000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.816000] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.816000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179573.816000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179573.816000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179573.816000] mice: PS/2 mouse device common for all mice
[17179573.816000] EISA: Probing bus 0 at eisa.0
[17179573.816000] EISA: Detected 0 cards.
[17179573.816000] NET: Registered protocol family 2
[17179573.852000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179573.856000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179573.856000] TCP established hash table entries: 131072 (order: 7, 524288 bytes)
[17179573.856000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[17179573.856000] TCP: Hash tables configured (established 131072 bind 65536)
[17179573.856000] TCP reno registered
[17179573.856000] TCP bic registered
[17179573.856000] NET: Registered protocol family 1
[17179573.856000] NET: Registered protocol family 8
[17179573.856000] NET: Registered protocol family 20
[17179573.856000] Using IPI Shortcut mode
[17179573.856000] ACPI wakeup devices:
[17179573.856000] UAR1 PS2K PS2M EHCI ILAN P7P8 P7P9 P2PB PCI1 PCI2 USB1 USB2 USB3 USB4 SLPB
[17179573.856000] ACPI: (supports S0 S1 S3 S4 S5)
[17179573.856000] Freeing unused kernel memory: 288k freed
[17179573.904000] vga16fb: initializing
[17179573.904000] vga16fb: mapped to 0xc00a0000
[17179574.036000] Console: switching to colour frame buffer device 80x25
[17179574.036000] fb0: VGA16 VGA frame buffer device
[17179575.100000] Capability LSM initialized
[17179575.216000] ACPI: Processor [CPU1] (supports 16 throttling states)
[17179575.716000] SCSI subsystem initialized
[17179575.720000] ACPI: bus type scsi registered
[17179575.720000] libata version 1.20 loaded.
[17179575.720000] sata_via 0000:00:0f.0: version 1.1
[17179575.720000] ACPI: PCI Interrupt 0000:00:0f.0 -> GSI 21 (level, low) -> IRQ 193
[17179575.720000] PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 1
[17179575.720000] ConfigSpace offset 49H: 0xa0
[17179575.720000] sata_via 0000:00:0f.0: routed to hard irq line 1
[17179575.720000] ata1: PATA max UDMA/133 cmd 0xEC00 ctl 0xE882 bmdma 0xE400 irq 193
[17179575.720000] ata2: PATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0xE408 irq 193
[17179575.884000] ata1: dev 0 cfg 00:045a 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f 93:0000
[17179575.884000] ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48
[17179575.884000] sata_get_dev_handle: SATA dev addr=0xf0000, handle=0xdffe9b20
[17179575.900000] ata1: dev 1 cfg 00:045a 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f 93:0000
[17179575.900000] ata1: dev 1 ATA-7, max UDMA/133, 160836480 sectors: LBA48
[17179575.900000] sata_get_dev_handle: SATA dev addr=0xf0000, handle=0xdffe9b20
[17179575.908000] ata1: dev 0 configured for UDMA/133
[17179575.908000] ata1: dev 1 configured for UDMA/133
[17179575.912000] sata_get_dev_handle: SATA dev addr=0xf0000, handle=0xdffe9b20
[17179575.920000] scsi0 : sata_via
[17179577.088000] ata2: disabling port
[17179577.088000] scsi1 : sata_via
[17179577.088000]   Vendor: ATA       Model: HDS728080PLA380   Rev: PF2O
[17179577.088000]   Type:   Direct-Access                      ANSI SCSI revision: 05
[17179577.088000]   Vendor: ATA       Model: HDS728080PLA380   Rev: PF2O
[17179577.088000]   Type:   Direct-Access                      ANSI SCSI revision: 05
[17179577.096000] Driver 'sd' needs updating - please use bus_type methods
[17179577.100000] SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
[17179577.100000] SCSI device sda: drive cache: write back
[17179577.104000] SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
[17179577.104000] SCSI device sda: drive cache: write back
[17179577.104000]  sda: sda1 sda2 sda3
[17179577.112000] sd 0:0:0:0: Attached scsi disk sda
[17179577.112000] SCSI device sdb: 160836480 512-byte hdwr sectors (82348 MB)
[17179577.120000] SCSI device sdb: drive cache: write back
[17179577.124000] SCSI device sdb: 160836480 512-byte hdwr sectors (82348 MB)
[17179577.124000] SCSI device sdb: drive cache: write back
[17179577.124000]  sdb: sdb1 sdb2 sdb3
[17179577.132000] sd 0:0:1:0: Attached scsi disk sdb
[17179577.336000] VP_IDE: IDE controller at PCI slot 0000:00:0f.1
[17179577.336000] PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
[17179577.336000] VP_IDE: chipset revision 7
[17179577.336000] VP_IDE: not 100% native mode: will probe irqs later
[17179577.336000] VP_IDE: VIA vt8251 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
[17179577.336000]     ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
[17179577.336000]     ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
[17179577.336000] Probing IDE interface ide0...
[17179578.204000] hda: DVDRW DRW-6S160P, ATAPI CD/DVD-ROM drive
[17179578.876000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179578.888000] Probing IDE interface ide1...
[17179579.464000] hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
[17179579.464000] Uniform CD-ROM driver Revision: 3.20
[17179579.548000] usbcore: registered new driver usbfs
[17179579.552000] usbcore: registered new driver hub
[17179579.552000] USB Universal Host Controller Interface driver v2.3
[17179579.552000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 201
[17179579.552000] PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9
[17179579.552000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[17179579.556000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[17179579.556000] uhci_hcd 0000:00:10.0: irq 201, io base 0x0000e080
[17179579.556000] hub 1-0:1.0: USB hub found
[17179579.556000] hub 1-0:1.0: 2 ports detected
[17179579.660000] ACPI: PCI Interrupt 0000:00:10.1[C] -> GSI 22 (level, low) -> IRQ 209
[17179579.660000] PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 1
[17179579.660000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[17179579.660000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[17179579.660000] uhci_hcd 0000:00:10.1: irq 209, io base 0x0000e000
[17179579.660000] hub 2-0:1.0: USB hub found
[17179579.660000] hub 2-0:1.0: 2 ports detected
[17179579.764000] ACPI: PCI Interrupt 0000:00:10.2 -> GSI 21 (level, low) -> IRQ 193
[17179579.764000] PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 1
[17179579.764000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[17179579.764000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[17179579.764000] uhci_hcd 0000:00:10.2: irq 193, io base 0x0000dc00
[17179579.764000] hub 3-0:1.0: USB hub found
[17179579.764000] hub 3-0:1.0: 2 ports detected
[17179579.868000] ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 217
[17179579.868000] PCI: Via IRQ fixup for 0000:00:10.3, from 3 to 9
[17179579.868000] uhci_hcd 0000:00:10.3: UHCI Host Controller
[17179579.868000] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[17179579.868000] uhci_hcd 0000:00:10.3: irq 217, io base 0x0000d880
[17179579.868000] hub 4-0:1.0: USB hub found
[17179579.868000] hub 4-0:1.0: 2 ports detected
[17179579.972000] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 22 (level, low) -> IRQ 209
[17179579.972000] PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 1
[17179579.972000] ehci_hcd 0000:00:10.4: EHCI Host Controller
[17179579.972000] ehci_hcd 0000:00:10.4: debug port 1
[17179579.972000] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[17179579.972000] ehci_hcd 0000:00:10.4: irq 209, io mem 0xfebff800
[17179579.972000] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179579.972000] hub 5-0:1.0: USB hub found
[17179579.972000] hub 5-0:1.0: 8 ports detected
[17179580.092000] Probing IDE interface ide1...
[17179580.676000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179580.676000] md: bitmap version 4.39
[17179580.676000] md: raid1 personality registered as nr 3
[17179580.800000] md: md0 stopped.
[17179580.800000] md: bind
[17179580.800000] md: bind
[17179580.800000] raid1: raid set md0 active with 2 out of 2 mirrors
[17179580.816000] md: md1 stopped.
[17179580.816000] md: bind
[17179580.816000] md: bind
[17179580.816000] raid1: raid set md1 active with 2 out of 2 mirrors
[17179580.836000] md: md2 stopped.
[17179580.836000] md: bind
[17179580.836000] md: bind
[17179580.836000] raid1: raid set md2 active with 2 out of 2 mirrors
[17179580.852000] Attempting manual resume
[17179580.888000] EXT3-fs: mounted filesystem with ordered data mode.
[17179580.892000] kjournald starting.  Commit interval 5 seconds
[17179586.832000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[17179586.832000] sd 0:0:1:0: Attached scsi generic sg1 type 0
[17179588.244000] Linux agpgart interface v0.101 (c) Dave Jones
[17179588.244000] agpgart: Detected VIA P4M800CE chipset
[17179588.256000] agpgart: AGP aperture is 128M @ 0xf0000000
[17179588.644000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
[17179588.644000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 217
[17179588.644000] PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 9
[17179588.644000] eth0: VIA Rhine II at 0x1d000, 00:17:31:d3:01:87, IRQ 217.
[17179588.644000] eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 40a1.
[17179588.920000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179588.932000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179589.276000] Real Time Clock Driver v1.12
[17179589.412000] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209
[17179589.412000] PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 1
[17179589.412000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[17179589.560000] logips2pp: Detected unknown logitech mouse model 1
[17179589.576000] input: PC Speaker as /class/input/input1
[17179589.584000] parport: PnPBIOS parport detected.
[17179589.584000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179589.884000] Floppy drive(s): fd0 is 1.44M
[17179589.904000] FDC 0 is a post-1991 82077
[17179590.096000] input: PS/2 Logitech Mouse as /class/input/input2
[17179590.496000] eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
[17179590.656000] PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
[17179590.656000] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 225
[17179590.656000] PCI: Via IRQ fixup for 0000:02:01.0, from 0 to 1
[17179590.656000] PCI: Setting latency timer of device 0000:02:01.0 to 64
[17179590.672000] ts: Compaq touchscreen protocol output
[17179590.688000] hda-intel: no codecs found!
[17179590.696000] ACPI: PCI interrupt for device 0000:02:01.0 disabled
[17179591.032000] lp0: using parport0 (interrupt-driven).
[17179591.084000] Adding 979832k swap on /dev/md1.  Priority:-1 extents:1 across:979832k
[17179591.292000] EXT3 FS on md0, internal journal
[17179591.608000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[17179592.016000] cdrom: open failed.
[17179592.312000] kjournald starting.  Commit interval 5 seconds
[17179592.316000] EXT3 FS on md2, internal journal
[17179592.316000] EXT3-fs: mounted filesystem with ordered data mode.
[17179593.160000] ACPI: Power Button (FF) [PWRF]
[17179593.160000] ACPI: Sleep Button (CM) [SLPB]
[17179593.160000] ACPI: Power Button (CM) [PWRB]
[17179593.256000] ibm_acpi: ec object not found
[17179593.284000] pcc_acpi: loading...
[17179597.124000] ppdev: user-space parallel port driver
[17179597.584000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179597.584000] apm: overridden by ACPI.
[17179604.812000] NET: Registered protocol family 10
[17179604.812000] lo: Disabled Privacy Extensions
[17179604.812000] IPv6 over IPv4 tunneling driver
[17179605.156000] Bluetooth: Core ver 2.8
[17179605.156000] NET: Registered protocol family 31
[17179605.156000] Bluetooth: HCI device and connection manager initialized
[17179605.156000] Bluetooth: HCI socket layer initialized
[17179605.176000] Bluetooth: L2CAP ver 2.8
[17179605.176000] Bluetooth: L2CAP socket layer initialized
[17179605.180000] Bluetooth: RFCOMM socket layer initialized
[17179605.180000] Bluetooth: RFCOMM TTY layer initialized
[17179605.180000] Bluetooth: RFCOMM ver 1.7
[17179615.708000] eth0: no IPv6 routers present
[17179982.284000] eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
[17179992.788000] eth0: no IPv6 routers present

Vervolgens heb ik geprobeerd met modprobe rtl8139 de driver te laden. Werkt niet, kan de rtl8139 niet vinden. Toen ben ik gaan zoeken in de drivers omgeving en vond de rtl8139cp en rtl8139too . Na het geven van modprobe rtl8139cp en modprobe rtl8139too komen beide netwerken nog niet op.
Geef ik dmesg dan komen netjes de volgende regels erbij:

[17257742.860000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17257851.756000] 8139too Fast Ethernet driver 0.9.27

Lijkt erop dat dit de juiste drivers moeten zijn, maar werkt niet.
Kan iemand mij melden wat ik fout heb gedaan of ergens fout ben gegaan ? Ik ben al aardig lang aan het doorspitten maar kom er niet uit. Ik heb ook alle ubunto.nl forums doorgelopen omdat ik niet dezelfde vraag wilde stellen als dat deze al beantwoord zou zijn. Maar ik kom er echt niet uit.
Ik heb ook al geprobeert de drivers te downloaden, maar kan deze niet vinden.
Ook geprobeert de rtl8139-diag te downloaden. Dit lukte wel, maar 'cc' werkte niet.

Alvast bedankt,

AvR

Offline Tukcedo

  • Lid
    • http://www.tukcedo.nl
  • Steunpunt: Nee
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #1 Gepost op: 2006/11/02, 14:10:53 »
Als de module is geladen, dan wil dat nog niet meteen zeggen dat je een werkend netwerk hebt: dat moet eerst geconfigureerd worden. Als je bijv. een IP adres e.d. kan ophalen bij een DHCP server zoals een ADSL router, dan doe je simpelweg:

sudo dhclient eth0

om de zaak te testen. Verder kun je via systeembeheer-menu een vast IP adres instellen e.d. Als de module correct is geladen, zal het commando:

ifconfig -a

in elk geval een (ongeconfigureerde) eth0 interface laten zien.
Tukcedo Services - Unix en Linux Consultants
http://www.tukcedo.nl

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #2 Gepost op: 2006/11/02, 14:57:17 »
eth0 is werkend. Nu nog de eth1. Maar deze krijg ik niet aan de gang.
Ofwel, ik wil twee ethernetkaarten aan de gang hebben.

AvR

Offline Tukcedo

  • Lid
    • http://www.tukcedo.nl
  • Steunpunt: Nee
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #3 Gepost op: 2006/11/03, 10:54:06 »
OK, maar die eth1 zit dan waarschijnlijk aan een ander netwerk. Als dat netwerk ook DHCP biedt, dan kun je met hetzelfde dhclient commando (maar dan met eth1 natuurlijk) een IP adres verkrijgen.

Vaak echter zul je in geval van twee netwerkkaarten tenminste eentje een vast adres geven. Anderen hebben in dit Forum al uitgelegd hoe je dat precies doet via de grafische interface. Gebruik dus even de zoekfunctie voor "vast adres".

O ja, is deze tweede kaart hetzelfde merk/model als je eerste? Anders moet je de driver hiervoor uiteraard apart laden.
Tukcedo Services - Unix en Linux Consultants
http://www.tukcedo.nl

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #4 Gepost op: 2006/11/03, 12:56:57 »
De tweede ethernetkaart zit (nog) niet in een netwerk.
Ik heb uberhaupt geen eth1.
De netwerkkaart is een Sweex (RealTeK8139), de eth0 is een onboard (volgens mij een VIA).
Wel vind ik ergens in de passage (zie eerste inzet):

[17179573.424000] pnp: PnP ACPI: found 15 devices
[17179573.424000] PnPBIOS: Disabled by ACPI PNP
[17179573.424000] PCI: Using ACPI for IRQ routing
[17179573.424000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179573.440000] PCI: Device 0000:02:01.0 not found by BIOS
[17179573.440000] pnp: 00:0c: ioport range 0xc00-0xc0f has been reserved

Mogelijk dat 'not found by BIOS' een hint is.
De netwerkkaart heb ik begin vorige week in een MS-WindowsXP bak gezet en daarin deed deze het goed. Vervolgens deze kaart overgezet in deze machine (de overige hardware is identiek met deze machine) en vervolgens bleef de machine hangen bij het booten. Vervolgens via de bios de IRQ's opnieuw op ACPI gezet en toen kwam het geheel weer goed op m.u.v. de 2e netwerkkaart.
Ik heb overigens 2 identieke netwerkkaarten, beide doen het niet.

AvR

Offline Tukcedo

  • Lid
    • http://www.tukcedo.nl
  • Steunpunt: Nee
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #5 Gepost op: 2006/11/03, 13:19:38 »
OK, het wordt langzaam wat duidelijker wat je wilt (sorry daarvoor ...). Heb je geprobeerd om de rtl8139 driver te laden? Ik zit niet achter een recent Ubuntu bakkie momenteel, dus het wordt een beetje uit m'n hoofd freubelen vrees ik.

Doe es:

/sbin/modprobe -l | grep 8139

of

/sbin/modprobe -l | grep rtl

Hier moet de locatie van een module uitkomen als het goed is, de naam eindigt in iets van .../rtl8139.ko
Vervolgens probeer je die te laden:

sudo /sbin/modprobe rtl8139

Als het niet lukt kun je met "dmesg" zien wat er aan de hand was.

Als het nou wel lukt, dan kun je in het bestand /etc/modprobe.conf opgeven welke kaart (eigenlijk: ethernet interface) welke driver gebruikt, bijv:

alias eth0 3c59x
alias eth1 rtl8139

Als alles goed gaat krijg je met:

ifconfig -a

Nu ook een eth1 te zien. We zijn benieuwd ...
Tukcedo Services - Unix en Linux Consultants
http://www.tukcedo.nl

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #6 Gepost op: 2006/11/03, 15:16:20 »
Ik vind alleen een 8139cp en een 8139too .
Deze had al middels modprobe 8139cp en 8139too geladen.
Alleen het alias heb ik nog niet gedaan.

De alias toegevoegd in /etc/modprobe.conf .
Nog een keer modprobe 8139cp en nog een soelaas.
Helaas.

AvR

Offline Tukcedo

  • Lid
    • http://www.tukcedo.nl
  • Steunpunt: Nee
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #7 Gepost op: 2006/11/03, 16:31:40 »
Maar wat gebeurt er nou als je die modules laadt: error meldingen? Je kunt met dmesg kijken wat er onder water gebeurt. En blijven die modules geladen of verdwijnen ze (lsmod | grep 8139)? Zo ja, dan is er wat mis en vindt je zeker wat in dmesg.
Tukcedo Services - Unix en Linux Consultants
http://www.tukcedo.nl

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #8 Gepost op: 2006/11/03, 17:41:14 »
In de dmesg staat hetvolgende

[17257742.860000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17257851.756000] 8139too Fast Ethernet driver 0.9.27

(zoals boven in eerste inzet)

lsmod | grep 8139 geeft:

8139too                26880  0
8139cp                 22528  0
mii                     5888  3 8139too,8139cp,via_rhine

In dmesg krijg ik geen bijzonderheden.

AvR

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #9 Gepost op: 2006/11/03, 17:42:15 »
Sorry,

Of ik foutmeldingen krijg tijdens het laden ?
Nee.

AvR

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #10 Gepost op: 2006/11/08, 08:12:52 »
?

Iemand nog suggesties ?

AvR

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #11 Gepost op: 2006/11/16, 15:41:26 »
Ik heb inmiddels een andere netwerkkaart erin gezet, nu lijkt het erop dat ik een IRQ probleem heb.

Als ik in de lijst kijk van dmesg (zie eerste bijdrage) komt volgende passage voor:

[17179573.412000] pnp: PnP ACPI init
[17179573.424000] pnp: PnP ACPI: found 15 devices
[17179573.424000] PnPBIOS: Disabled by ACPI PNP
[17179573.424000] PCI: Using ACPI for IRQ routing
[17179573.424000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179573.440000] PCI: Device 0000:02:01.0 not found by BIOS

Moet ik ergens PnPBIOS aanzetten ?
Wat betekent/doet de opmerking 'pci=routeirq' ? Waar moet ik dit invullen ?
Ik heb een tweede PC ernaast staan met exact dezelfde configuratie (moederbord, interfaces, randapparatuur, hardware-instelling, BIOS-instellingen) welk draait onder (helaas MS-WindowsXP) en de kaarten doen het hier wel goed in.
Ik heb ook een oude (200Mhz ...) PC met dezelfde Linux distributie (alleen hier de server geinstalleerd, dus geen volledige installatie), hier de netwerkkaarten in gehad, en hier doen ze het ook goed in.

Lijkt er dus op dat de hardware heel moet zijn.
Iemand nog iets wat ik mogelijk vergeten ben ?

AvR

ruitenag

  • Gast
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #12 Gepost op: 2006/11/29, 23:57:59 »
Is er nog iemand met een suggestie ?
Moet ik misschien een ander merk pakken ?
Ik zit ook te overwegen om er een draadloze netwerkkaart in te plaatsen, heeft iemand nog suggesties voor een goede netwerkkaart (die in ieder geval werkt !) ?

Alvast bedankt,

AvR

Offline Tukcedo

  • Lid
    • http://www.tukcedo.nl
  • Steunpunt: Nee
Sweex netwerkkaart (RTL8139) werkt niet.
« Reactie #13 Gepost op: 2006/11/30, 16:38:52 »
Dat "pci=routeirq" is een bootstring die je mee kunt geven aan het boot proces. Nou ben ik niet zo'n grub kenner, maar je kunt op een gegeven moment in plaats van je Ubuntu te kiezen ook "e" (uit m'n hoofd kiezen). Daar zou je dan deze string moeten opgeven: "boot pci=routeirq" of zoiets.

Toch twijfel ik eraan of je IRQ problemen hebt (tenzij er 20 kaarten in je bak zitten natuurlijk) want PCI regelt dat normaal gesproken perfect. Wat je kunt doen is om even "lspci" te doen. De module MOET namelijk aangeven wat-ie herkent. Mijn vermoeden is dat-ie niks ziet, c.q. het is niet de juiste module ... O ja, laat meteen even je /etc/modprobe.conf zien!
Tukcedo Services - Unix en Linux Consultants
http://www.tukcedo.nl