Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: muis werkt niet na hybernate/suspend  (gelezen 3418 keer)

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Gepost op: 2006/01/02, 23:05:10 »
Hoi allemaal,

Dit is mijn eerste post op dit forum.
Prima discussies en hulp.
Ik gebruik Breezy sinds 2 maanden op mijn oude Dell Inspiron 7000. Die had ik bijna bij het oud vuil gezet, want met windows werd het niks.
Nu draait 'ie als een zonnetje, wlan en alles.

Behalve,...
als ik het scherm sluit gaat mijn notebook in hybernate of suspend mode.
Doe ik 'm weer open, dan werkt alles perfect, behalve mijn usb-muis.

Enig idee hoe dit komt of hoe ik de muis dan weer aan de praat krijgt zonder opnieuw op te starten?

thnx

Offline Dennis Kaarsemaker

  • Administrator
    • dennis
    • http://www.kaarsemaker.net
  • Steunpunt: Nee
muis werkt niet na hybernate/suspend
« Reactie #1 Gepost op: 2006/01/03, 00:43:51 »
Doe eens een lsmod voordat je suspend en post de uitvoer daarvan mee

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Reactie #2 Gepost op: 2006/01/03, 13:09:16 »
Dag Dennis,

Hierbij de uitvoer van lsmod:

Module                  Size  Used by
rfcomm                 34972  0
l2cap                  22404  3 rfcomm
bluetooth              43012  2 rfcomm,l2cap
cpufreq_userspace       4444  0
cpufreq_stats           5124  0
freq_table              4484  1 cpufreq_stats
cpufreq_powersave       1920  0
cpufreq_ondemand        5916  0
cpufreq_conservative     6820  0
pcmcia                 24584  4
apm                    19308  1
ipv6                  217408  8
af_packet              20232  2
ndiswrapper           114376  0
floppy                 52692  0
irtty_sir               7808  0
sir_dev                17324  1 irtty_sir
irda                  159804  2 irtty_sir,sir_dev
crc_ccitt               2176  1 irda
pcspkr                  3652  0
rtc                    11832  0
snd_es1968             26368  1
gameport               14472  1 snd_es1968
snd_ac97_codec         72188  1 snd_es1968
snd_pcm_oss            46368  0
snd_mixer_oss          16128  1 snd_pcm_oss
snd_pcm                78344  3 snd_es1968,snd_ac97_codec,snd_pcm_oss
snd_page_alloc         10120  2 snd_es1968,snd_pcm
snd_mpu401_uart         6784  1 snd_es1968
i2c_piix4               8336  0
i2c_core               19728  1 i2c_piix4
8139too                23552  0
mii                     5248  1 8139too
yenta_socket           22540  4
rsrc_nonstatic         12032  1 yenta_socket
pcmcia_core            44932  3 pcmcia,yenta_socket,rsrc_nonstatic
pci_hotplug            24628  0
intel_agp              21276  1
agpgart                32328  1 intel_agp
dm_mod                 50364  1
joydev                  9280  0
tsdev                   7616  0
snd_seq_dummy           3844  0
snd_seq_oss            29440  0
snd_seq_midi            8608  0
snd_rawmidi            22816  2 snd_mpu401_uart,snd_seq_midi
snd_seq_midi_event      6656  2 snd_seq_oss,snd_seq_midi
snd_seq                44688  7 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_m idi_event
snd_timer              21764  2 snd_pcm,snd_seq
snd_seq_device          8204  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmi di,snd_seq
evdev                   9088  1
snd                    48644  14 snd_es1968,snd_ac97_codec,snd_pcm_oss,snd_mixer _oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_d evice
soundcore               9184  1 snd
psmouse                26116  0
mousedev               10912  1
parport_pc             31812  1
lp                     11460  0
parport                32072  2 parport_pc,lp
md                     40656  0
ext3                  115976  1
jbd                    48536  1 ext3
processor              23100  0
usbhid                 30688  0
uhci_hcd               28048  0
usbcore               104316  4 ndiswrapper,usbhid,uhci_hcd
ide_cd                 36996  0
cdrom                  33952  1 ide_cd
ide_disk               16128  3
ide_generic             1664  0
piix                    9476  1
ide_core              125268  4 ide_cd,ide_disk,ide_generic,piix
unix                   24624  707
vesafb                  8088  0
capability              5000  0
commoncap               6784  1 capability
vga16fb                12232  1
vgastate                8320  1 vga16fb
softcursor              2432  2 vesafb,vga16fb
cfbimgblt               2944  2 vesafb,vga16fb
cfbfillrect             3840  2 vesafb,vga16fb
cfbcopyarea             4480  2 vesafb,vga16fb
fbcon                  34176  72
tileblit                2560  1 fbcon
font                    8448  1 fbcon
bitblit                 5248  1 fbcon


Waar moet ik naar kijken?

Offline Dennis Kaarsemaker

  • Administrator
    • dennis
    • http://www.kaarsemaker.net
  • Steunpunt: Nee
muis werkt niet na hybernate/suspend
« Reactie #3 Gepost op: 2006/01/03, 14:00:55 »
OK, nu nog de uitvoer van lsusb :)

Het volgende kun je proberen:
Na resumen (als je muis niet werkt) overschakelen naar de console met , daar inloggen en de volgende commandos uitproberen:

sudo modprobe -r psmouse
sudo modprobe psmouse

Daarna schakel je weer terug naar de grafische omgeving met . Na enige seconden moet je muis het weer doen.

Werkt dit niet, herhaal de truc, maar dan met usbhid inplaats van psmouse.

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Reactie #4 Gepost op: 2006/01/03, 21:48:47 »
uitvoer lsusb

Bus 001 Device 002: ID 1241:1166 Belkin
Bus 001 Device 001: ID 0000:0000


Ik zal je suggestie eens uitproberen.

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Reactie #5 Gepost op: 2006/01/03, 22:05:31 »
helaas,

het lukt niet met modprobe -r psmouse of usbhid

overigens, mijn touchpad-mouse doet het wel.

Offline Dennis Kaarsemaker

  • Administrator
    • dennis
    • http://www.kaarsemaker.net
  • Steunpunt: Nee
muis werkt niet na hybernate/suspend
« Reactie #6 Gepost op: 2006/01/03, 22:16:18 »
Na modprobe -r wel weer modprobe doen he...

Werkt de USB muis wel als je hem eruit haal en er weer insteekt?

Offline Dennis Kaarsemaker

  • Administrator
    • dennis
    • http://www.kaarsemaker.net
  • Steunpunt: Nee
muis werkt niet na hybernate/suspend
« Reactie #7 Gepost op: 2006/01/03, 22:17:13 »
Bij de weg: stuur de uitvoer van dmesg (zowel na resumen als na resumen en uithalen en insteken van de muis) eens mee.

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Reactie #8 Gepost op: 2006/01/03, 22:31:57 »
Uiteraard ook na modprobe -r ook modprobe weer gedaan. Helaas.

USB-muis eruit en er weer in werkt ook niet.
Hier komt dan uitput van dmesg voor suspend:
**********
[4294667.296000] Linux version 2.6.12-10-386 (buildd@terranova) (gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 Thu Dec 22 11:37:10 UTC 2005
[4294667.296000] BIOS-provided physical RAM map:
[4294667.296000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[4294667.296000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[4294667.296000]  BIOS-e820: 00000000000eb800 - 0000000000100000 (reserved)
[4294667.296000]  BIOS-e820: 0000000000100000 - 000000000c000000 (usable)
[4294667.296000]  BIOS-e820: 00000000fffeb800 - 0000000100000000 (reserved)
[4294667.296000] 0MB HIGHMEM available.
[4294667.296000] 192MB LOWMEM available.
[4294667.296000] On node 0 totalpages: 49152
[4294667.296000]   DMA zone: 4096 pages, LIFO batch:1
[4294667.296000]   Normal zone: 45056 pages, LIFO batch:31
[4294667.296000]   HighMem zone: 0 pages, LIFO batch:1
[4294667.296000] DMI not present.
[4294667.296000] ACPI: Unable to locate RSDP
[4294667.296000] Allocating PCI resources starting at 0c000000 (gap: 0c000000:f3feb800)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=/dev/hda1 ro quiet splash
[4294667.296000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[4294667.296000] mapped APIC to ffffd000 (01181000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 1024 (order: 10, 16384 bytes)
[    0.000000] Detected 400.098 MHz processor.
[ 1271.125627] Using tsc for high-res timesource
[ 1271.127207] Console: colour VGA+ 80x25
[ 1271.128358] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1271.129257] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 1271.162905] Memory: 186500k/196608k available (1416k kernel code, 9592k reserved, 762k data, 224k init, 0k highmem)
[ 1271.162925] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 1271.163192] Calibrating delay loop... 788.48 BogoMIPS (lpj=394240)
[ 1271.186304] Security Framework v1.0.0 initialized
[ 1271.186327] SELinux:  Disabled at boot.
[ 1271.186375] Mount-cache hash table entries: 512
[ 1271.186717] CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 1271.186750] CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 1271.186792] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 1271.186806] CPU: L2 cache: 256K
[ 1271.186818] CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
[ 1271.186843] CPU: Intel Mobile Pentium II stepping 0a
[ 1271.186860] Enabling fast FPU save and restore... done.
[ 1271.186878] Checking 'hlt' instruction... OK.
[ 1271.190208] Checking for popad bug... OK.
[ 1271.190718] checking if image is initramfs... it is
[ 1273.203121] Freeing initrd memory: 5172k freed
[ 1273.205747] NET: Registered protocol family 16
[ 1273.205880] EISA bus registered
[ 1273.206327] PCI: PCI BIOS revision 2.10 entry at 0xfd9d3, last bus=1
[ 1273.206354] PCI: Using configuration type 1
[ 1273.206369] mtrr: v2.0 (20020519)
[ 1273.207873] ACPI: Subsystem revision 20050729
[ 1273.207887] ACPI: Interpreter disabled.
[ 1273.207902] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1273.207951] pnp: PnP ACPI: disabled
[ 1273.207965] PnPBIOS: Scanning system for PnP BIOS support...
[ 1273.208027] PnPBIOS: Found PnP BIOS installation structure at 0xc00f6e60
[ 1273.208045] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb3ba, dseg 0x400
[ 1273.226369] PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
[ 1273.226549] PCI: Probing PCI hardware
[ 1273.226564] PCI: Probing PCI hardware (bus 00)
[ 1273.227888] Boot video device is 0000:01:00.0
[ 1273.229820] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
[ 1273.229854] PCI: IRQ 0 for device 0000:00:04.0 doesn't match PIRQ mask - try pci=usepirqmask
[ 1273.229874] PCI: Found IRQ 11 for device 0000:00:04.0
[ 1273.229906] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1273.229949] PCI: IRQ 0 for device 0000:00:04.1 doesn't match PIRQ mask - try pci=usepirqmask
[ 1273.229966] PCI: Found IRQ 11 for device 0000:00:04.1
[ 1273.232571] pnp: 00:00: ioport range 0x401-0x407 has been reserved
[ 1273.232588] pnp: 00:00: ioport range 0x3810-0x388f has been reserved
[ 1273.232636] pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[ 1273.232652] pnp: 00:0a: ioport range 0x8000-0x803f has been reserved
[ 1273.232669] pnp: 00:0a: ioport range 0x2180-0x218f has been reserved
[ 1273.235188] audit: initializing netlink socket (disabled)
[ 1273.235219] audit: initialized
[ 1273.235613] VFS: Disk quotas dquot_6.5.1
[ 1273.235696] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1273.235814] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[ 1273.235838] devfs: boot_options: 0x0
[ 1273.235985] Initializing Cryptographic API
[ 1273.236008] Limiting direct PCI/PCI transfers.
[ 1273.236409] isapnp: Scanning for PnP cards...
[ 1273.589817] isapnp: No Plug & Play device found
[ 1273.673003] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 1273.681265] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1273.682278] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1273.682298] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
[ 1273.682678] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1273.683156] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1273.692308] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1273.692805] io scheduler noop registered
[ 1273.692888] io scheduler anticipatory registered
[ 1273.692910] io scheduler deadline registered
[ 1273.692956] io scheduler cfq registered
[ 1273.694792] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1273.696502] EISA: Probing bus 0 at eisa.0
[ 1273.696537] Cannot allocate resource for EISA slot 3
[ 1273.696571] Cannot allocate resource for EISA slot 8
[ 1273.696582] EISA: Detected 0 cards.
[ 1273.696688] NET: Registered protocol family 2
[ 1273.706058] IP: routing cache hash table of 2048 buckets, 16Kbytes
[ 1273.706626] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1273.706987] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 1273.707163] TCP: Hash tables configured (established 8192 bind 8192)
[ 1273.707523] NET: Registered protocol family 8
[ 1273.707537] NET: Registered protocol family 20
[ 1273.709111] Freeing unused kernel memory: 224k freed
[ 1273.771635] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 1273.783667] vga16fb: initializing
[ 1273.783683] vga16fb: mapped to 0xc00a0000
[ 1273.921051] Console: switching to colour frame buffer device 80x30
[ 1273.921077] fb0: VGA16 VGA frame buffer device
[ 1275.175700] Capability LSM initialized
[ 1275.232539] NET: Registered protocol family 1
[ 1275.296768] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1275.296809] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1275.319369] PIIX4: IDE controller at PCI slot 0000:00:07.1
[ 1275.319416] PIIX4: chipset revision 1
[ 1275.319427] PIIX4: not 100% native mode: will probe irqs later
[ 1275.319457]     ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:DMA, hdb:pio
[ 1275.319497]     ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:DMA, hdd:pio
[ 1275.319532] Probing IDE interface ide0...
[ 1275.582752] hda: FUJITSU MHG2102AT, ATA DISK drive
[ 1276.198712] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 1276.198924] Probing IDE interface ide1...
[ 1276.870573] hdc: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
[ 1277.176434] ide1 at 0x170-0x177,0x376 on irq 15
[ 1277.176791] Probing IDE interface ide2...
[ 1277.689302] Probing IDE interface ide3...
[ 1278.202230] Probing IDE interface ide4...
[ 1278.715158] Probing IDE interface ide5...
[ 1279.247273] hda: max request size: 128KiB
[ 1279.326879] hda: 19640880 sectors (10056 MB) w/512KiB Cache, CHS=19485/16/63, UDMA(33)
[ 1279.326905] hda: cache flushes not supported
[ 1279.327162]  /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
[ 1279.411524] hdc: ATAPI 24X CD-ROM drive, 128kB Cache
[ 1279.411551] Uniform CD-ROM driver Revision: 3.20
[ 1280.619861] Attempting manual resume
[ 1280.620457] swsusp: Suspend partition has wrong signature?
[ 1280.880027] usbcore: registered new driver usbfs
[ 1280.880153] usbcore: registered new driver hub
[ 1280.886334] USB Universal Host Controller Interface driver v2.2
[ 1280.886567] PCI: Found IRQ 11 for device 0000:00:07.2
[ 1280.886630] uhci_hcd 0000:00:07.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
[ 1280.948300] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 1280.948334] uhci_hcd 0000:00:07.2: irq 11, io base 0x0000fce0
[ 1280.948908] hub 1-0:1.0: USB hub found
[ 1280.948950] hub 1-0:1.0: 2 ports detected
[ 1281.117830] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 1281.271638] hub 1-0:1.0: over-current change on port 2
[ 1283.134949] usbcore: registered new driver hiddev
[ 1283.197250] input: USB HID v1.10 Mouse [1241:1166] on usb-0000:00:07.2-1
[ 1283.197282] usbcore: registered new driver usbhid
[ 1283.197294] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[ 1284.869567] Attempting manual resume
[ 1284.901314] swsusp: Suspend partition has wrong signature?
[ 1284.990861] kjournald starting.  Commit interval 5 seconds
[ 1284.990906] EXT3-fs: mounted filesystem with ordered data mode.
[ 1287.532353] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 1296.648993] Adding 433712k swap on /dev/hda5.  Priority:-1 extents:1
[ 1297.273304] EXT3 FS on hda1, internal journal
[ 1319.254625] parport: PnPBIOS parport detected.
[ 1319.254712] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 1319.361017] lp0: using parport0 (interrupt-driven).
[ 1319.622672] mice: PS/2 mouse device common for all mice
[ 1320.913413] Synaptics Touchpad, model: 1, fw: 4.3, id: 0x8858a1, caps: 0x0/0x0
[ 1320.936270] input: SynPS/2 Synaptics TouchPad on isa0060/serio1
[ 1322.422162] ts: Compaq touchscreen protocol output
[ 1327.520745] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[ 1329.935313] hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
[ 1329.935338] hdc: packet command error: error=0x50 { LastFailedSense=0x05 }
[ 1329.935355] ide: failed opcode was: unknown
[ 1329.936128] cdrom: open failed.
[ 1335.049343] Linux agpgart interface v0.101 (c) Dave Jones
[ 1335.093449] agpgart: Detected an Intel 440BX Chipset.
[ 1335.141403] agpgart: AGP aperture is 64M @ 0xe0000000
[ 1335.606639] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1335.633218] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 1336.070561] Linux Kernel Card Services
[ 1336.070585]   options:  [pci] [cardbus] [pm]
[ 1336.140226] PCI: Found IRQ 11 for device 0000:00:04.0
[ 1336.140273] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1336.140328] Yenta: CardBus bridge found at 0000:00:04.0 [1028:0085]
[ 1336.140402] Yenta: Enabling burst memory read transactions
[ 1336.140418] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 1336.140431] Yenta: Routing CardBus interrupts to PCI
[ 1336.140449] Yenta TI: socket 0000:00:04.0, mfunc 0x01021c72, devctl 0x66
[ 1336.361708] Yenta: ISA IRQ mask 0x0618, PCI irq 11
[ 1336.361724] Socket status: 30000068
[ 1336.433596] PCI: Found IRQ 11 for device 0000:00:04.1
[ 1336.433673] Yenta: CardBus bridge found at 0000:00:04.1 [1028:0085]
[ 1336.433748] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 1336.433760] Yenta: Routing CardBus interrupts to PCI
[ 1336.433778] Yenta TI: socket 0000:00:04.1, mfunc 0x01021c72, devctl 0x66
[ 1336.654662] Yenta: ISA IRQ mask 0x0618, PCI irq 11
[ 1336.654677] Socket status: 30000068
[ 1337.821554] 8139too Fast Ethernet driver 0.9.27
[ 1337.840250] PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
[ 1337.840304] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1337.845507] eth0: RealTek RTL8139 at 0x4000, 00:10:d7:0a:00:bc, IRQ 11
[ 1337.845524] eth0:  Identified 8139 chip type 'RTL-8139B'
[ 1339.022633] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
[ 1339.743190] PCI: Found IRQ 5 for device 0000:00:08.0
[ 1339.743291] es1968: not attempting power management.
[ 1340.332523] es1968: clocking to 48000
[ 1344.848340] Real Time Clock Driver v1.12
[ 1345.446082] input: PC Speaker
[ 1346.780933] irda_init()
[ 1346.781005] NET: Registered protocol family 23
[ 1347.007664] Floppy drive(s): fd0 is 1.44M
[ 1347.022341] FDC 0 is a post-1991 82077
[ 1349.407341] ndiswrapper version 1.1 loaded (preempt=no,smp=no)
[ 1349.535259] ndiswrapper: driver bcmwl5 (Broadcom,06/25/2004, 3.40.73.0) loaded
[ 1349.535948] PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
[ 1349.536055] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 1349.550080] ndiswrapper: using irq 11
[ 1350.202599] wlan0: ndiswrapper ethernet device 00:11:50:37:c2:34 using driver bcmwl5, configuration file 14E4:4320.5.conf
[ 1350.203155] wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
[ 1351.631688] NET: Registered protocol family 17
[ 1356.584406] NET: Registered protocol family 10
[ 1356.584956] Disabled Privacy Extensions on device c02eb280(lo)
[ 1356.585638] IPv6 over IPv4 tunneling driver
[ 1367.341724] wlan0: no IPv6 routers present
********

En na suspend
***********************************
[4294667.296000] Linux version 2.6.12-10-386 (buildd@terranova) (gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 Thu Dec 22 11:37:10 UTC 2005
[4294667.296000] BIOS-provided physical RAM map:
[4294667.296000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[4294667.296000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[4294667.296000]  BIOS-e820: 00000000000eb800 - 0000000000100000 (reserved)
[4294667.296000]  BIOS-e820: 0000000000100000 - 000000000c000000 (usable)
[4294667.296000]  BIOS-e820: 00000000fffeb800 - 0000000100000000 (reserved)
[4294667.296000] 0MB HIGHMEM available.
[4294667.296000] 192MB LOWMEM available.
[4294667.296000] On node 0 totalpages: 49152
[4294667.296000]   DMA zone: 4096 pages, LIFO batch:1
[4294667.296000]   Normal zone: 45056 pages, LIFO batch:31
[4294667.296000]   HighMem zone: 0 pages, LIFO batch:1
[4294667.296000] DMI not present.
[4294667.296000] ACPI: Unable to locate RSDP
[4294667.296000] Allocating PCI resources starting at 0c000000 (gap: 0c000000:f3feb800)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=/dev/hda1 ro quiet splash
[4294667.296000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[4294667.296000] mapped APIC to ffffd000 (01181000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 1024 (order: 10, 16384 bytes)
[    0.000000] Detected 400.098 MHz processor.
[ 1271.125627] Using tsc for high-res timesource
[ 1271.127207] Console: colour VGA+ 80x25
[ 1271.128358] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1271.129257] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 1271.162905] Memory: 186500k/196608k available (1416k kernel code, 9592k reserved, 762k data, 224k init, 0k highmem)
[ 1271.162925] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 1271.163192] Calibrating delay loop... 788.48 BogoMIPS (lpj=394240)
[ 1271.186304] Security Framework v1.0.0 initialized
[ 1271.186327] SELinux:  Disabled at boot.
[ 1271.186375] Mount-cache hash table entries: 512
[ 1271.186717] CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 1271.186750] CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 1271.186792] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 1271.186806] CPU: L2 cache: 256K
[ 1271.186818] CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
[ 1271.186843] CPU: Intel Mobile Pentium II stepping 0a
[ 1271.186860] Enabling fast FPU save and restore... done.
[ 1271.186878] Checking 'hlt' instruction... OK.
[ 1271.190208] Checking for popad bug... OK.
[ 1271.190718] checking if image is initramfs... it is
[ 1273.203121] Freeing initrd memory: 5172k freed
[ 1273.205747] NET: Registered protocol family 16
[ 1273.205880] EISA bus registered
[ 1273.206327] PCI: PCI BIOS revision 2.10 entry at 0xfd9d3, last bus=1
[ 1273.206354] PCI: Using configuration type 1
[ 1273.206369] mtrr: v2.0 (20020519)
[ 1273.207873] ACPI: Subsystem revision 20050729
[ 1273.207887] ACPI: Interpreter disabled.
[ 1273.207902] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1273.207951] pnp: PnP ACPI: disabled
[ 1273.207965] PnPBIOS: Scanning system for PnP BIOS support...
[ 1273.208027] PnPBIOS: Found PnP BIOS installation structure at 0xc00f6e60
[ 1273.208045] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb3ba, dseg 0x400
[ 1273.226369] PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
[ 1273.226549] PCI: Probing PCI hardware
[ 1273.226564] PCI: Probing PCI hardware (bus 00)
[ 1273.227888] Boot video device is 0000:01:00.0
[ 1273.229820] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
[ 1273.229854] PCI: IRQ 0 for device 0000:00:04.0 doesn't match PIRQ mask - try pci=usepirqmask
[ 1273.229874] PCI: Found IRQ 11 for device 0000:00:04.0
[ 1273.229906] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1273.229949] PCI: IRQ 0 for device 0000:00:04.1 doesn't match PIRQ mask - try pci=usepirqmask
[ 1273.229966] PCI: Found IRQ 11 for device 0000:00:04.1
[ 1273.232571] pnp: 00:00: ioport range 0x401-0x407 has been reserved
[ 1273.232588] pnp: 00:00: ioport range 0x3810-0x388f has been reserved
[ 1273.232636] pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[ 1273.232652] pnp: 00:0a: ioport range 0x8000-0x803f has been reserved
[ 1273.232669] pnp: 00:0a: ioport range 0x2180-0x218f has been reserved
[ 1273.235188] audit: initializing netlink socket (disabled)
[ 1273.235219] audit: initialized
[ 1273.235613] VFS: Disk quotas dquot_6.5.1
[ 1273.235696] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1273.235814] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[ 1273.235838] devfs: boot_options: 0x0
[ 1273.235985] Initializing Cryptographic API
[ 1273.236008] Limiting direct PCI/PCI transfers.
[ 1273.236409] isapnp: Scanning for PnP cards...
[ 1273.589817] isapnp: No Plug & Play device found
[ 1273.673003] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 1273.681265] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1273.682278] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1273.682298] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
[ 1273.682678] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1273.683156] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1273.692308] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1273.692805] io scheduler noop registered
[ 1273.692888] io scheduler anticipatory registered
[ 1273.692910] io scheduler deadline registered
[ 1273.692956] io scheduler cfq registered
[ 1273.694792] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1273.696502] EISA: Probing bus 0 at eisa.0
[ 1273.696537] Cannot allocate resource for EISA slot 3
[ 1273.696571] Cannot allocate resource for EISA slot 8
[ 1273.696582] EISA: Detected 0 cards.
[ 1273.696688] NET: Registered protocol family 2
[ 1273.706058] IP: routing cache hash table of 2048 buckets, 16Kbytes
[ 1273.706626] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1273.706987] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 1273.707163] TCP: Hash tables configured (established 8192 bind 8192)
[ 1273.707523] NET: Registered protocol family 8
[ 1273.707537] NET: Registered protocol family 20
[ 1273.709111] Freeing unused kernel memory: 224k freed
[ 1273.771635] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 1273.783667] vga16fb: initializing
[ 1273.783683] vga16fb: mapped to 0xc00a0000
[ 1273.921051] Console: switching to colour frame buffer device 80x30
[ 1273.921077] fb0: VGA16 VGA frame buffer device
[ 1275.175700] Capability LSM initialized
[ 1275.232539] NET: Registered protocol family 1
[ 1275.296768] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1275.296809] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1275.319369] PIIX4: IDE controller at PCI slot 0000:00:07.1
[ 1275.319416] PIIX4: chipset revision 1
[ 1275.319427] PIIX4: not 100% native mode: will probe irqs later
[ 1275.319457]     ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:DMA, hdb:pio
[ 1275.319497]     ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:DMA, hdd:pio
[ 1275.319532] Probing IDE interface ide0...
[ 1275.582752] hda: FUJITSU MHG2102AT, ATA DISK drive
[ 1276.198712] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 1276.198924] Probing IDE interface ide1...
[ 1276.870573] hdc: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
[ 1277.176434] ide1 at 0x170-0x177,0x376 on irq 15
[ 1277.176791] Probing IDE interface ide2...
[ 1277.689302] Probing IDE interface ide3...
[ 1278.202230] Probing IDE interface ide4...
[ 1278.715158] Probing IDE interface ide5...
[ 1279.247273] hda: max request size: 128KiB
[ 1279.326879] hda: 19640880 sectors (10056 MB) w/512KiB Cache, CHS=19485/16/63, UDMA(33)
[ 1279.326905] hda: cache flushes not supported
[ 1279.327162]  /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
[ 1279.411524] hdc: ATAPI 24X CD-ROM drive, 128kB Cache
[ 1279.411551] Uniform CD-ROM driver Revision: 3.20
[ 1280.619861] Attempting manual resume
[ 1280.620457] swsusp: Suspend partition has wrong signature?
[ 1280.880027] usbcore: registered new driver usbfs
[ 1280.880153] usbcore: registered new driver hub
[ 1280.886334] USB Universal Host Controller Interface driver v2.2
[ 1280.886567] PCI: Found IRQ 11 for device 0000:00:07.2
[ 1280.886630] uhci_hcd 0000:00:07.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
[ 1280.948300] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 1280.948334] uhci_hcd 0000:00:07.2: irq 11, io base 0x0000fce0
[ 1280.948908] hub 1-0:1.0: USB hub found
[ 1280.948950] hub 1-0:1.0: 2 ports detected
[ 1281.117830] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 1281.271638] hub 1-0:1.0: over-current change on port 2
[ 1283.134949] usbcore: registered new driver hiddev
[ 1283.197250] input: USB HID v1.10 Mouse [1241:1166] on usb-0000:00:07.2-1
[ 1283.197282] usbcore: registered new driver usbhid
[ 1283.197294] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[ 1284.869567] Attempting manual resume
[ 1284.901314] swsusp: Suspend partition has wrong signature?
[ 1284.990861] kjournald starting.  Commit interval 5 seconds
[ 1284.990906] EXT3-fs: mounted filesystem with ordered data mode.
[ 1287.532353] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 1296.648993] Adding 433712k swap on /dev/hda5.  Priority:-1 extents:1
[ 1297.273304] EXT3 FS on hda1, internal journal
[ 1319.254625] parport: PnPBIOS parport detected.
[ 1319.254712] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 1319.361017] lp0: using parport0 (interrupt-driven).
[ 1319.622672] mice: PS/2 mouse device common for all mice
[ 1320.913413] Synaptics Touchpad, model: 1, fw: 4.3, id: 0x8858a1, caps: 0x0/0x0
[ 1320.936270] input: SynPS/2 Synaptics TouchPad on isa0060/serio1
[ 1322.422162] ts: Compaq touchscreen protocol output
[ 1327.520745] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[ 1329.935313] hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
[ 1329.935338] hdc: packet command error: error=0x50 { LastFailedSense=0x05 }
[ 1329.935355] ide: failed opcode was: unknown
[ 1329.936128] cdrom: open failed.
[ 1335.049343] Linux agpgart interface v0.101 (c) Dave Jones
[ 1335.093449] agpgart: Detected an Intel 440BX Chipset.
[ 1335.141403] agpgart: AGP aperture is 64M @ 0xe0000000
[ 1335.606639] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1335.633218] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 1336.070561] Linux Kernel Card Services
[ 1336.070585]   options:  [pci] [cardbus] [pm]
[ 1336.140226] PCI: Found IRQ 11 for device 0000:00:04.0
[ 1336.140273] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1336.140328] Yenta: CardBus bridge found at 0000:00:04.0 [1028:0085]
[ 1336.140402] Yenta: Enabling burst memory read transactions
[ 1336.140418] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 1336.140431] Yenta: Routing CardBus interrupts to PCI
[ 1336.140449] Yenta TI: socket 0000:00:04.0, mfunc 0x01021c72, devctl 0x66
[ 1336.361708] Yenta: ISA IRQ mask 0x0618, PCI irq 11
[ 1336.361724] Socket status: 30000068
[ 1336.433596] PCI: Found IRQ 11 for device 0000:00:04.1
[ 1336.433673] Yenta: CardBus bridge found at 0000:00:04.1 [1028:0085]
[ 1336.433748] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 1336.433760] Yenta: Routing CardBus interrupts to PCI
[ 1336.433778] Yenta TI: socket 0000:00:04.1, mfunc 0x01021c72, devctl 0x66
[ 1336.654662] Yenta: ISA IRQ mask 0x0618, PCI irq 11
[ 1336.654677] Socket status: 30000068
[ 1337.821554] 8139too Fast Ethernet driver 0.9.27
[ 1337.840250] PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
[ 1337.840304] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1337.845507] eth0: RealTek RTL8139 at 0x4000, 00:10:d7:0a:00:bc, IRQ 11
[ 1337.845524] eth0:  Identified 8139 chip type 'RTL-8139B'
[ 1339.022633] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
[ 1339.743190] PCI: Found IRQ 5 for device 0000:00:08.0
[ 1339.743291] es1968: not attempting power management.
[ 1340.332523] es1968: clocking to 48000
[ 1344.848340] Real Time Clock Driver v1.12
[ 1345.446082] input: PC Speaker
[ 1346.780933] irda_init()
[ 1346.781005] NET: Registered protocol family 23
[ 1347.007664] Floppy drive(s): fd0 is 1.44M
[ 1347.022341] FDC 0 is a post-1991 82077
[ 1349.407341] ndiswrapper version 1.1 loaded (preempt=no,smp=no)
[ 1349.535259] ndiswrapper: driver bcmwl5 (Broadcom,06/25/2004, 3.40.73.0) loaded
[ 1349.535948] PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
[ 1349.536055] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 1349.550080] ndiswrapper: using irq 11
[ 1350.202599] wlan0: ndiswrapper ethernet device 00:11:50:37:c2:34 using driver bcmwl5, configuration file 14E4:4320.5.conf
[ 1350.203155] wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
[ 1351.631688] NET: Registered protocol family 17
[ 1356.584406] NET: Registered protocol family 10
[ 1356.584956] Disabled Privacy Extensions on device c02eb280(lo)
[ 1356.585638] IPv6 over IPv4 tunneling driver
[ 1367.341724] wlan0: no IPv6 routers present
[ 1565.401710] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 1569.433806] cs: IO port probe 0x100-0x4ff: clean.
[ 1569.435248] cs: IO port probe 0x100-0x4ff: clean.
[ 1569.437693] cs: IO port probe 0xc00-0xcf7: clean.
[ 1569.438098] cs: IO port probe 0xc00-0xcf7: clean.
[ 1569.439506] cs: IO port probe 0xa00-0xaff: clean.
[ 1569.439924] cs: IO port probe 0xa00-0xaff: clean.
[ 1607.115910] IDE device ACPI handler is NULL
[ 1607.115961] IDE device ACPI handler is NULL
[ 1610.633568] hub 1-0:1.0: resubmit --> -108
[   16.012117] PCI: Found IRQ 11 for device 0000:00:04.0
[   16.012160] PCI: Sharing IRQ 11 with 0000:01:00.0
[   16.012499] hub 1-0:1.0: hub_port_status failed (err = -108)
[   16.012518] hub 1-0:1.0: hub_port_status failed (err = -108)
[   16.527006] PCI: Found IRQ 11 for device 0000:00:04.1
[   17.229942] PCI: Found IRQ 11 for device 0000:00:07.2
[   17.291855] PCI: Found IRQ 11 for device 0000:00:07.2
[   18.025574] IDE device ACPI handler is NULL
[   18.043343] IDE device ACPI handler is NULL
[   18.093506] PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
[   18.106592] ndiswrapper: using irq 11
*********************************

Geeft dit bruikbare info?

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Reactie #9 Gepost op: 2006/01/07, 20:15:23 »
Iemand enig idee?

Offline Dennis Kaarsemaker

  • Administrator
    • dennis
    • http://www.kaarsemaker.net
  • Steunpunt: Nee
muis werkt niet na hybernate/suspend
« Reactie #10 Gepost op: 2006/01/08, 13:42:20 »
Totaal niet :/

Ik denk dat je het beste een bug kunt filen op bugzilla.ubuntu.com, component linux, met de mededeling dat de usb muis driver faalt. Ben Collins (de kernel master) weet hier een stuk meer van dan iedereen op dit forum bij elkaar :)

gosh

  • Gast
muis werkt niet na hybernate/suspend
« Reactie #11 Gepost op: 2006/01/08, 13:47:22 »
Oke, zal ik doen.

Dank Dennis.