Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: TV-Kaart installeren  (gelezen 6531 keer)

Vess

  • Gast
TV-Kaart installeren
« Gepost op: 2009/01/04, 00:25:29 »
Goede avond,

ik heb laatst een TVkaart TVPI03 van e-tech gekocht. Dit om lekker tv te kunnen kijken op mijn computer. Ik moet hem nu installeren alleen hoe?
Citaat
Success! I have cable in the Netherlands and a PC with a tvcard from e-tech. Model number TVPI03 (that's a cheap 30euro card).
It works well under windows (with some hideous software that is on the product cd.
It did not work easily in Ubuntu 7.10 Gutsy Gibbon. Now I have tv with sound (through sox, alsa using PAL-I) with tvtime.

Acknowledgements: My steps are based on advice by david_2001 on http://ubuntuforums.org/showthread.php?t=352196&page=5
(which is for a different card though). And a great clue by peter missel on http://marc.info/?l=linux-video&m=116811879125416&w=2
where he identifies the e-tech TVPI03 card as a flavour of Lifeview Platinum FM.

My steps are as follows:
I have /etc/modules unchange (no extra line with saa7134 e.g.).
I have a file /etc/modprobe.d/saa7134 with a single line:

options saa7134 card=54 alsa=1

I run dmesg to see if the card is detected, and get:

saa7133[0]: found at 0000:01:09.0, rev: 209, irq: 19, latency: 32, mmio: 0xe0004000
saa7133[0]: subsystem: 4e42:5214, board: LifeView FlyTV Platinum FM / Gold [card=54,insmod option]
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xe0004000 irq 19 registered as card -2

Then I run tvtime-scanner, which scans for channels (takes some time). You only need to do this once... the command creates a channel list. After finishing scanning, you can run tvtime. Either from the terminal, or from the applications menu. Tvtime should give you images.

Now to get sound going...

First I do:

sudo alsactl names
which writes in "/etc/asound.names". That file reads, in my case,

ctl {
alsactl1 {
name hw:0
comment 'Physical Device - NVidia nForce2 with ALC650F
at irq 18
'
}
alsactl2 {
name hw:1
comment 'Physical Device - MPU-401 UART at 0x330, irq
10'
}
alsactl3 {
name hw:2
comment 'Physical Device - saa7133[0] at 0xe0004000 irq
19'
}....

The bold value (about the saa7133) is what you need in the command below:
Type in a terminal:

sox -r 32000 -w -t alsa hw:2,0 -t alsa pcm.default &

This gives me tv+sound with tvtime audio set on PAL-BG! Slight sound-delay, same as under windows.

Next time you log on "tvtime &" in a terminal and then the sox command suffice.
Dit is van iemand die het is gelukt. Nu is de vraag moet ik eerst TVtime installeren voordat ik de TV kaart in mijn computer zet? Want het lukt mij niet om er TV op te kijken.
1.I have /etc/modules unchange (no extra line with saa7134 e.g.).
Heb ik.
2.I  have a file /etc/modprobe.d/saa7134 with a single line:

options saa7134 card=54 alsa=1

Gedaan.
« Laatst bewerkt op: 2009/01/04, 00:27:35 door Vess »

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #1 Gepost op: 2009/01/04, 00:26:29 »
3.I run dmesg to see if the card is detected, and get:
[   34.457785] ACPI: Power Button (FF) [PWRF]
[   34.457847] input: Power Button (CM) as /devices/virtual/input/input2
[   34.489735] ACPI: Power Button (CM) [PWRB]
[   34.654965] ACPI: WMI-Acer: Mapper loaded
[   34.900685] input: PC Speaker as /devices/platform/pcspkr/input/input3
[   34.915438] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   34.916810] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   34.920391] eth0: no link during initialization.
[   34.927843] usbcore: registered new interface driver hiddev
[   34.940350] input:   USB Keyboard as /devices/pci0000:00/0000:00:04.0/usb2/2-5/2-5:1.0/input/input4
[   34.963988] input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:04.0-5
[   34.987140] input:   USB Keyboard as /devices/pci0000:00/0000:00:04.0/usb2/2-5/2-5:1.1/input/input5
[   35.012012] input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:04.0-5
[   35.016179] input: Full-Speed Mouse Full-Speed Mouse as /devices/pci0000:00/0000:00:04.0/usb2/2-6/2-6:1.0/input/input6
[   35.043910] input,hidraw2: USB HID v1.10 Mouse [Full-Speed Mouse Full-Speed Mouse] on usb-0000:00:04.0-6
[   35.043922] usbcore: registered new interface driver usbhid
[   35.043924] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   35.048786] usbcore: registered new interface driver libusual
[   35.073498] Initializing USB Mass Storage driver...
[   35.079813] scsi6 : SCSI emulation for USB Mass Storage devices
[   35.079856] usb-storage: device found at 4
[   35.079858] usb-storage: waiting for device to settle before scanning
[   35.079880] usbcore: registered new interface driver usb-storage
[   35.079882] USB Mass Storage support registered.
[   35.084564] Linux video capture interface: v2.00
[   35.107563] Linux agpgart interface v0.102
[   35.171277] nvidia: module license 'NVIDIA' taints kernel.
[   35.422285] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 10
[   35.422288] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNEB] -> GSI 10 (level, low) -> IRQ 10
[   35.422296] PCI: Setting latency timer of device 0000:02:00.0 to 64
[   35.422462] NVRM: loading NVIDIA UNIX x86 Kernel Module  169.12  Thu Feb 14 17:53:07 PST 2008
[   35.437617] saa7130/34: v4l2 driver version 0.2.14 loaded
[   35.437892] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[   35.437894] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[   35.437901] saa7133[0]: found at 0000:01:05.0, rev: 209, irq: 10, latency: 64, mmio: 0xf9fff800
[   35.437905] saa7133[0]: subsystem: 4e42:5214, board: UNKNOWN/GENERIC [card=0,autodetected]
[   35.437911] saa7133[0]: board init: gpio is 31400
[   35.570988] saa7133[0]: i2c eeprom 00: 42 4e 14 52 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[   35.570996] saa7133[0]: i2c eeprom 10: 00 00 01 00 ff 20 ff ff ff ff ff ff ff ff ff ff
[   35.571003] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 b1 ff ff ff ff
[   35.571009] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   35.571016] saa7133[0]: i2c eeprom 40: ff 22 00 c2 96 ff 02 30 10 ff ff ff ff ff ff ff
[   35.571022] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   35.571028] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   35.571035] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   35.573184] saa7133[0]: registered device video0 [v4l2]
[   35.573198] saa7133[0]: registered device vbi0
[   35.592293] saa7134 ALSA driver for DMA sound loaded
[   35.592317] saa7133[0]/alsa: saa7133[0] at 0xf9fff800 irq 10 registered as card -2
[   35.644982] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 7
[   35.644985] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LAZA] -> GSI 7 (level, low) -> IRQ 7
[   35.645000] PCI: Setting latency timer of device 0000:00:09.0 to 64
[   36.090417] NET: Registered protocol family 17
[   36.112044] lp: driver loaded but no devices found
[   36.148167] Adding 9863868k swap on /dev/sda5.  Priority:-1 extents:1 across:9863868k
[   36.675769] EXT3 FS on sda1, internal journal
[   37.534683] ip_tables: (C) 2000-2006 Netfilter Core Team
[   37.755324] No dock devices found.
[   38.496671] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   38.496674] apm: disabled - APM is not SMP safe.
[   38.596981] ppdev: user-space parallel port driver
[   38.709790] audit(1231021437.655:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5389 profile="/usr/sbin/cupsd" namespace="default"
[   40.071947] usb-storage: device scan complete
[   40.078692] scsi 6:0:0:0: Direct-Access     Generic- Compact Flash    1.00 PQ: 0 ANSI: 0 CCS
[   40.085555] scsi 6:0:0:1: Direct-Access     Generic- SM/xD-Picture    1.00 PQ: 0 ANSI: 0 CCS
[   40.092668] scsi 6:0:0:2: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[   40.099657] scsi 6:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.00 PQ: 0 ANSI: 0 CCS
[   40.103670] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[   40.103708] sd 6:0:0:0: Attached scsi generic sg2 type 0
[   40.107675] sd 6:0:0:1: [sdc] Attached SCSI removable disk
[   40.107720] sd 6:0:0:1: Attached scsi generic sg3 type 0
[   40.111658] sd 6:0:0:2: [sdd] Attached SCSI removable disk
[   40.111694] sd 6:0:0:2: Attached scsi generic sg4 type 0
[   40.115665] sd 6:0:0:3: [sde] Attached SCSI removable disk
[   40.115701] sd 6:0:0:3: Attached scsi generic sg5 type 0
[   40.724762] Bluetooth: Core ver 2.11
[   40.725189] NET: Registered protocol family 31
[   40.725192] Bluetooth: HCI device and connection manager initialized
[   40.725196] Bluetooth: HCI socket layer initialized
[   40.752477] Bluetooth: L2CAP ver 2.9
[   40.752482] Bluetooth: L2CAP socket layer initialized
[   40.817221] Bluetooth: RFCOMM socket layer initialized
[   40.817236] Bluetooth: RFCOMM TTY layer initialized
[   40.817238] Bluetooth: RFCOMM ver 1.8
[   78.679158] NET: Registered protocol family 10
[   78.679400] lo: Disabled Privacy Extensions
[   78.679886] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   91.045641] UDF-fs: Partition marked readonly; forcing readonly mount
[   91.073543] UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'Crocodile Dundee in LA', timestamp 2036/02/07 11:58 (103c)
[  120.003280] eth0: link up.
[  120.005548] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  120.871251] eth0: link down.
[  127.352817] eth0: link up.
[  128.219480] eth0: link down.
[  129.781610] eth0: link up.
[  130.647619] eth0: link down.
[  130.917621] eth0: no IPv6 routers present
[  132.210403] eth0: link up.
[  133.075758] eth0: link down.
[  134.639524] eth0: link up.
[  135.503898] eth0: link down.
[  137.068319] eth0: link up.
[  137.932039] eth0: link down.
[  139.528530] eth0: link up.
[  140.360194] eth0: link down.
[  142.103932] eth0: link up.
[  142.916271] eth0: link down.
[  144.532722] eth0: link up.
[  145.344405] eth0: link down.
[  146.961517] eth0: link up.
[  147.772546] eth0: link down.
[  149.432199] eth0: link up.
[  150.264495] eth0: link down.
[  151.861316] eth0: link up.
[  152.692636] eth0: link down.
[  169.062157] eth0: link up.
[  169.881373] eth0: link down.
[  174.003521] eth0: link up.
[  174.865602] eth0: link down.
[  181.332123] eth0: link up.
[  182.150019] eth0: link down.
[  186.493382] eth0: link up.
[  187.325684] eth0: link down.
[  191.435067] eth0: link up.
[  192.245773] eth0: link down.
[  193.863869] eth0: link up.
[  194.673914] eth0: link down.
[  201.579584] eth0: link up.
[  202.405671] eth0: link down.
[  203.998235] eth0: link up.
[  204.833809] eth0: link down.
[  209.295634] eth0: link up.
[  210.137428] eth0: link down.
[  211.713957] eth0: link up.
[  212.565565] eth0: link down.
[  214.132278] eth0: link up.
[  214.993706] eth0: link down.
[  221.429456] eth0: link up.
[  222.278124] eth0: link down.
[  223.847780] eth0: link up.
[  224.706262] eth0: link down.
[  233.856162] eth0: link up.
[  234.674394] eth0: link down.
[  238.672190] eth0: link up.
[  239.530671] eth0: link down.
[  248.377219] eth0: link up.
[  249.243228] eth0: link down.
[  250.806085] eth0: link up.
[  251.671366] eth0: link down.
[  253.234806] eth0: link up.
[  254.099833] eth0: link down.
[  255.663598] eth0: link up.
[  256.527975] eth0: link down.
[  258.092719] eth0: link up.
[  258.956111] eth0: link down.
[  260.584343] eth0: link up.
[  261.448062] eth0: link down.
[  263.075967] eth0: link up.
[  263.940012] eth0: link down.
[  267.985914] eth0: link up.
[  268.796289] eth0: link down.
[  270.456921] eth0: link up.
[  271.288241] eth0: link down.
[  275.398282] eth0: link up.
[  276.208659] eth0: link down.
[  277.774716] eth0: link up.
[  278.636798] eth0: link down.
[  280.234925] eth0: link up.
[  281.064937] eth0: link down.
[  285.270858] eth0: link up.
[  286.112980] eth0: link down.
[  294.975562] eth0: link up.
[  295.825535] eth0: link down.
[  297.425298] eth0: link up.
[  298.253674] eth0: link down.
[  302.314630] eth0: link up.
[  303.173764] eth0: link down.
[  307.214100] eth0: link up.
[  308.030042] eth0: link down.
[  309.611478] eth0: link up.
[  310.458180] eth0: link down.
[  312.072013] eth0: link up.
[  312.886319] eth0: link down.
[  314.469392] eth0: link up.
[  315.314458] eth0: link down.
[  319.463112] eth0: link up.
[  320.298360] eth0: link down.
[  321.923651] eth0: link up.
[  322.790639] eth0: link down.
[  326.802178] eth0: link up.
[  327.646917] eth0: link down.
[  331.691181] eth0: link up.
[  332.503193] eth0: link down.
[  336.643341] eth0: link up.
[  337.487096] eth0: link down.
[  341.689419] eth0: link up.
[  342.535139] eth0: link down.
[  344.181042] eth0: link up.
[  345.027090] eth0: link down.
[  349.196033] eth0: link up.
[  350.011319] eth0: link down.
[  354.085035] eth0: link up.
[  354.931409] eth0: link down.
[  361.371416] eth0: link up.
[  362.215827] eth0: link down.
[  366.302632] eth0: link up.
[  367.136243] eth0: link down.
[  368.731425] eth0: link up.
[  369.564382] eth0: link down.
[  371.160236] eth0: link up.
[  371.992521] eth0: link down.
[  373.589011] eth0: link up.
[  374.420660] eth0: link down.
[  383.398758] eth0: link up.
[  384.260840] eth0: link down.
[  385.984629] eth0: link up.
[  386.816932] eth0: link down.
[  391.062449] eth0: link up.
[  391.928785] eth0: link down.
[  393.637847] eth0: link up.
[  394.484548] eth0: link down.
[  396.066641] eth0: link up.
[  396.912688] eth0: link down.
[  398.495434] eth0: link up.
[  399.340826] eth0: link down.
[  403.479077] eth0: link up.
[  404.325056] eth0: link down.
[  406.117237] eth0: link up.
[  406.944960] eth0: link down.
[  408.577446] eth0: link up.
[  409.436910] eth0: link down.
[  411.037655] eth0: link up.
[  411.865049] eth0: link down.
[  413.497863] eth0: link up.
[  414.357001] eth0: link down.
[  416.020903] eth0: link up.
[  416.849279] eth0: link down.
[  428.207085] eth0: link up.
[  429.053785] eth0: link down.
[  433.075143] eth0: link up.
[  433.910064] eth0: link down.
[  435.493791] eth0: link up.
[  436.338202] eth0: link down.
[  445.272124] eth0: link up.
[  446.114570] eth0: link down.
[  455.217677] eth0: link up.
[  456.082703] eth0: link down.
[  457.698827] eth0: link up.
[  458.510841] eth0: link down.
[  472.406085] eth0: link up.
[  521.936683] eth0: no IPv6 routers present
[  526.174401] eth0: link down.
[  545.727665] eth0: link up.
[  545.729631] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  546.563240] eth0: link down.
[  550.575107] eth0: link up.
[  550.577146] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  551.419517] eth0: link down.
[  565.682254] eth0: link up.
[  565.684190] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  566.499504] eth0: link down.
[  573.021321] eth0: link up.
[  573.023341] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  573.847733] eth0: link down.
[  575.450113] eth0: link up.
[  576.275872] eth0: link down.
[  577.868434] eth0: link up.
[  577.870476] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  578.704011] eth0: link down.
[  582.862155] eth0: link up.
[  582.864130] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  583.688240] eth0: link down.
[  585.238917] eth0: link up.
[  586.052567] eth0: link down.
[  595.048339] eth0: link up.
[  595.050305] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  595.892747] eth0: link down.
[  597.487930] eth0: link up.
[  598.320887] eth0: link down.
[  602.345516] eth0: link up.
[  602.347485] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  603.177164] eth0: link down.
[  607.182486] eth0: link up.
[  607.184511] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  608.033442] eth0: link down.
[  612.207621] eth0: link up.
[  612.209578] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  613.017671] eth0: link down.
[  614.856322] eth0: link up.
[  615.701388] eth0: link down.
[  625.032252] eth0: link up.
[  625.034327] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  625.861282] eth0: link down.
[  627.461046] eth0: link up.
[  628.289422] eth0: link down.
[  629.890167] eth0: link up.
[  629.892307] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  630.717561] eth0: link down.
[  632.318960] eth0: link up.

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #2 Gepost op: 2009/01/04, 00:26:48 »
[  632.320849] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  633.145699] eth0: link down.
[  634.904830] eth0: link up.
[  635.765605] eth0: link down.
[  644.871653] eth0: link up.
[  644.873743] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  645.733734] eth0: link down.
[  652.336053] eth0: link up.
[  652.338062] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  653.145776] eth0: link down.
[  654.754375] eth0: link up.
[  655.573915] eth0: link down.
[  659.696063] eth0: link up.
[  659.698106] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  660.558144] eth0: link down.
[  662.166743] eth0: link up.
[  662.986284] eth0: link down.
[  667.013859] eth0: link up.
[  667.015828] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  667.842561] eth0: link down.
[  679.346971] eth0: link up.
[  679.348986] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  680.175020] eth0: link down.
[  681.754822] eth0: link up.
[  682.603160] eth0: link down.
[  689.093560] eth0: link up.
[  689.095566] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  689.951388] eth0: link down.
[  693.940675] eth0: link up.
[  693.942639] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  694.807666] eth0: link down.
[  698.819533] eth0: link up.
[  698.821552] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  699.663944] eth0: link down.
[  703.677137] eth0: link up.
[  703.679097] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  704.520222] eth0: link down.
[  711.026658] eth0: link up.
[  711.028717] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  711.868450] eth0: link down.
[  716.009905] eth0: link up.
[  716.011868] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  716.852680] eth0: link down.
[  721.003953] eth0: link up.
[  721.005917] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  721.836910] eth0: link down.
[  726.018616] eth0: link up.
[  726.020593] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  726.884624] eth0: link down.
[  728.594014] eth0: link up.
[  729.440716] eth0: link down.
[  731.085639] eth0: link up.
[  731.087505] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  731.932667] eth0: link down.
[  733.483343] eth0: link up.
[  734.296993] eth0: link down.
[  735.974968] eth0: link up.
[  735.976847] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  736.788944] eth0: link down.
[  738.372346] eth0: link up.
[  738.374224] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  739.217082] eth0: link down.
[  740.832555] eth0: link up.
[  741.645223] eth0: link down.
[  745.627637] eth0: link up.
[  745.629528] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  746.437688] eth0: link down.
[  752.903546] eth0: link up.
[  752.905742] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  753.722105] eth0: link down.
[  757.782404] eth0: link up.
[  757.784543] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  758.642195] eth0: link down.
[  760.253084] eth0: link up.
[  761.070335] eth0: link down.
[  765.110671] eth0: link up.
[  765.112752] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  765.926612] eth0: link down.
[  767.487106] eth0: link up.
[  768.354750] eth0: link down.
[  774.836644] eth0: link up.
[  774.838844] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  775.703306] eth0: link down.
[  779.725645] eth0: link up.
[  779.727781] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  780.559584] eth0: link down.
[  782.175709] eth0: link up.
[  782.987724] eth0: link down.
[  787.043768] eth0: link up.
[  787.045900] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  787.907813] eth0: link down.
[  789.598224] eth0: link up.
[  790.463904] eth0: link down.
[  792.027015] eth0: link up.
[  792.028895] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  792.892044] eth0: link down.
[  794.477080] eth0: link up.
[  794.478956] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  795.320182] eth0: link down.
[  799.428913] eth0: link up.
[  799.431003] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  800.240272] eth0: link down.
[  801.857706] eth0: link up.
[  802.668411] eth0: link down.
[  806.673734] eth0: link up.
[  806.675820] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  807.524688] eth0: link down.
[  809.123470] eth0: link up.
[  809.952828] eth0: link down.
[  823.853634] eth0: link up.
[  823.855766] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  824.713426] eth0: link down.
[  831.150487] eth0: link up.
[  831.152566] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  831.997842] eth0: link down.
[  838.657100] eth0: link up.
[  838.659223] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  839.474023] eth0: link down.
[  843.514688] eth0: link up.
[  843.516772] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  844.330301] eth0: link down.
[  845.943807] eth0: link up.
[  846.758441] eth0: link down.
[  850.738565] eth0: link up.
[  850.740708] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  851.550905] eth0: link down.
[  853.167357] eth0: link up.
[  853.979045] eth0: link down.
[  855.596478] eth0: link up.
[  855.598607] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  856.407183] eth0: link down.
[  860.443593] eth0: link up.
[  860.445723] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  861.263460] eth0: link down.
[  862.809557] eth0: link up.
[  863.627461] eth0: link down.
[  865.227878] eth0: link up.
[  865.230011] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  866.055600] eth0: link down.
[  867.845491] eth0: link up.
[  867.847364] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  868.675502] eth0: link down.
[  872.744964] eth0: link up.
[  872.747042] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  873.595593] eth0: link down.
[  877.728212] eth0: link up.
[  877.730265] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  878.579822] eth0: link down.
[ 1841.610689] eth0: link up.
[ 1841.612751] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1857.984143] eth0: no IPv6 routers present
[ 2046.906869] usb 1-1: new high speed USB device using ehci_hcd and address 5
[ 2047.041480] usb 1-1: configuration #1 chosen from 2 choices
[ 2047.041839] scsi7 : SCSI emulation for USB Mass Storage devices
[ 2047.042022] usb-storage: device found at 5
[ 2047.042026] usb-storage: waiting for device to settle before scanning
[ 2052.031138] usb-storage: device scan complete
[ 2052.033512] scsi 7:0:0:0: Direct-Access     Apple    iPod             1.62 PQ: 0 ANSI: 0
[ 2052.037613] sd 7:0:0:0: [sdf] 991232 2048-byte hardware sectors (2030 MB)
[ 2052.040483] sd 7:0:0:0: [sdf] Write Protect is off
[ 2052.040488] sd 7:0:0:0: [sdf] Mode Sense: 68 00 00 08
[ 2052.040491] sd 7:0:0:0: [sdf] Assuming drive cache: write through
[ 2052.048592] sd 7:0:0:0: [sdf] 991232 2048-byte hardware sectors (2030 MB)
[ 2052.051463] sd 7:0:0:0: [sdf] Write Protect is off
[ 2052.051467] sd 7:0:0:0: [sdf] Mode Sense: 68 00 00 08
[ 2052.051470] sd 7:0:0:0: [sdf] Assuming drive cache: write through
[ 2052.051473]  sdf: sdf1 sdf2
[ 2052.056497] sd 7:0:0:0: [sdf] Attached SCSI removable disk
[ 2052.056536] sd 7:0:0:0: Attached scsi generic sg6 type 0

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #3 Gepost op: 2009/01/04, 00:27:17 »
4.Then I run tvtime-scanner, which scans for channels (takes some time). You only need to do this once... the command creates a channel list. After finishing scanning, you can run tvtime. Either from the terminal, or from the applications menu. Tvtime should give you images.

Hier krijg ik niets te zien.

Kan iemand mij verder helpen?

Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #4 Gepost op: 2009/01/05, 10:43:23 »
lijkt erop dat de kaart goed herkent wordt

moet ik eerst TVtime installeren voordat ik de TV kaart in mijn computer zet?
lijkt me niet nodig...

wat staat er precies in /etc/modprobe.d/saa7134?


Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: TV-Kaart installeren
« Reactie #5 Gepost op: 2009/01/05, 15:48:22 »
Je driver is in ieder geval geladen [   35.437617] saa7130/34: v4l2 driver version 0.2.14 loaded
Ik heb zelf een PCTV Rave tv kaartje en ik gebruik KDETV, vind ik makkelijker in te stellen dan TV-Time. Ik zou zeggen probeer het uit, misschien herkent KDETV je kaart niet, de installatie is zo gebeurt en ook zo weer verwijdert mocht het niet werken.

Met vriendelijke groet,

Gijs
In der Beschränkung zeigt sich der Meister.

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #6 Gepost op: 2009/01/05, 19:56:37 »
@ drik
options saa7134 card=54 alsa=1
@Gijs
KDETV kan ik installeren zonder enige kde interface te installeren?

Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #7 Gepost op: 2009/01/05, 22:06:12 »
uit jouw dmesg zie ik

   35.437905] saa7133[0]: subsystem: 4e42:5214, board: UNKNOWN/GENERIC [card=0,autodetected]

dit zou card=54 moeten zijn
staat dit na herstart nog steeds als card=0 bij dmesg

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #8 Gepost op: 2009/01/05, 22:10:32 »
ja daar staat nu card=54

Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #9 Gepost op: 2009/01/05, 22:37:46 »

KDETV kan ik installeren zonder enige kde interface te installeren?

Groetjes Jurgen

ja, via synaptic
proberen waard


Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #10 Gepost op: 2009/01/05, 22:48:12 »
had je herstart na install tvtime en dus voor het scannen?
probeer anders nog eens
(voor alle zekerheid.... wel de kabel aangesloten...)

Offline Gijsbert

  • Lid
  • Steunpunt: Ja
Re: TV-Kaart installeren
« Reactie #11 Gepost op: 2009/01/06, 00:00:42 »
@ drik
options saa7134 card=54 alsa=1
@Gijs
KDETV kan ik installeren zonder enige kde interface te installeren?

Groetjes Jurgen
Ik gebruik zelf ook Gnome en heb KDETV gewoon geïnstalleerd. De meeste programma's zijn onderling te installeren. Het enigste wat niet werkt is het KDE help centrum.

Met vriendelijke groet,

Gijs
In der Beschränkung zeigt sich der Meister.

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #12 Gepost op: 2009/01/06, 11:14:42 »
@ drik
Ja na de herstart had ik gister wel een paar kanalen. Dan ga ik vanavond hoe het precies werkt.
@ gijs
Ik zal vanavond eens KDETV ernaast installeren en kijken of dat prettiger is om mee te werken.

Mijn dank jongens en ik laat nog even weten als ik eenmaal beeld heb!

Groetjes Jurgen

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #13 Gepost op: 2009/01/06, 20:46:37 »
Ok ik heb KDETV geinstalleerd en kanalen opgezocht. Hij doet het.
Desondanks dat ik beeld heb heb ik nog geen geluid. kan ik d.m.v. het onderstaande het geluid installeren of moet ik dat anders doen?

Now to get sound going...

First I do:

sudo alsactl names
which writes in "/etc/asound.names". That file reads, in my case,

ctl {
alsactl1 {
name hw:0
comment 'Physical Device - NVidia nForce2 with ALC650F
at irq 18
'
}
alsactl2 {
name hw:1
comment 'Physical Device - MPU-401 UART at 0x330, irq
10'
}
alsactl3 {
name hw:2
comment 'Physical Device - saa7133[0] at 0xe0004000 irq
19'
}....

The bold value (about the saa7133) is what you need in the command below:
Type in a terminal:

sox -r 32000 -w -t alsa hw:2,0 -t alsa pcm.default &


Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #14 Gepost op: 2009/01/06, 21:16:52 »
probeer het
in de 2e opdracht wel jouw gegevens invullen

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #15 Gepost op: 2009/01/06, 21:39:59 »
Hoe kom ik erachter wat de gegevens zijn die ik daar moet invullen?

Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #16 Gepost op: 2009/01/06, 21:41:59 »
doe eerst

sudo alsactl names

en post dan wat er in
/etc/asound.names
staat

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #17 Gepost op: 2009/01/06, 21:50:12 »
ctl {
ctl {
alsactl1 {
name hw:0
comment 'Physical Device - HDA NVidia at 0xf9e78000 irq 7'
}
alsactl2 {
name hw:1
comment 'Physical Device - saa7133[0] at 0xf9fff800 irq 10'
}
}
pcm {
alsactl1 {
name default:0
comment 'Abstract Device - Default Device (Duplex)'
}
alsactl2 {
name plug:default:0
comment 'Abstract Device With Conversions - Default Device (Duplex)'
}
alsactl3 {
name front:0
comment 'Abstract Device - Front Speakers (Duplex)'
}
alsactl4 {
name plug:front:0
comment 'Abstract Device With Conversions - Front Speakers (Duplex)'
}
alsactl5 {
name 'hw:0,0'
comment 'Physical Device - ALC883 Analog (Duplex)'
}
alsactl6 {
name 'plughw:0,0'
comment 'Physical Device With Conversions - ALC883 Analog (Duplex)'
}
alsactl7 {
name 'hw:0,4'
comment 'Physical Device - ALC883 Analog (Capture)'
}
alsactl8 {
name 'plughw:0,4'
comment 'Physical Device With Conversions - ALC883 Analog (Capture)'
}
alsactl9 {
name surround40:0
comment 'Abstract Device - Front and Rear Speakers (Duplex)'
}
alsactl10 {
name plug:surround40:0
comment 'Abstract Device With Conversions - Front and Rear Speakers (Duplex)'
}
alsactl11 {
name surround51:0
comment 'Abstract Device - Front, Rear, Center and Woofer (Duplex)'
}
alsactl12 {
name plug:surround51:0
comment 'Abstract Device With Conversions - Front, Rear, Center and Woofer (Duplex)'
}
alsactl13 {
name surround71:0
comment 'Abstract Device - Front, Rear, Side, Center and Woofer (Duplex)'
}
alsactl14 {
name plug:surround71:0
comment 'Abstract Device With Conversions - Front, Rear, Side, Center and Woofer (Duplex)'
}
alsactl15 {
name default:1
comment 'Abstract Device - Default Device (Capture)'
}
alsactl16 {
name plug:default:1
comment 'Abstract Device With Conversions - Default Device (Capture)'
}
alsactl17 {
name 'hw:1,0'
comment 'Physical Device - SAA7134 PCM (Capture)'
}
alsactl18 {
name 'plughw:1,0'
comment 'Physical Device With Conversions - SAA7134 PCM (Capture)'
}
}
rawmidi {
alsactl1 {
name virtual
comment 'Virtual Device - Sequencer (Duplex)'
}
alsactl2 {
name 'virtual:MERGE=0'
comment 'Virtual Device - Sequencer (No Merge) (Duplex)'
}
}
timer {
alsactl1 {
name 'hw:CLASS=1,SCLASS=0,CARD=-1,DEV=0,SUBDEV=0'
comment 'Physical Device - system timer'
}
}
seq {
alsactl1 {
name default
comment 'Default Device - Sequencer (Duplex)'
}
alsactl2 {
name hw
comment 'Physical Device - Sequencer (Duplex)'
}
}

Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #18 Gepost op: 2009/01/06, 22:04:23 »
name hw:2
comment 'Physical Device - saa7133[0] at 0xe0004000 irq
19'

The bold value (about the saa7133) is what you need in the command below:
Type in a terminal:

sox -r 32000 -w -t alsa hw:2,0 -t alsa pcm.default &

in jouw
/etc/asound.names
(file die je hebt aangemaakt door commando sudo alsactl names)
staat

name hw:1
      comment 'Physical Device - saa7133[0] at 0xf9fff800 irq 10'

uitgaande van dat de manier die jij volgt klopt verander je hw:2 in hw:1

de volgende opdracht zou dan moeten werken

sox -r 32000 -w -t alsa hw:1,0 -t alsa pcm.default &

duimen

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #19 Gepost op: 2009/01/06, 22:11:03 »
sox is not installed. Installeren maar?

Groetjes Jurgen

Edit:
Veranderd maar als ik
sox -r 32000 -w -t alsa hw:1,0 -t alsa pcm.default &
invoer krijg ik de melding
jurgen@jurgen-desktop:~$ sox -r 32000 -w -t alsa hw:1,0 -t alsa pcm.default &
[1] 7018
jurgen@jurgen-desktop:~$ sox soxio: Failed reading `hw:1,0': unknown file type `alsa'
« Laatst bewerkt op: 2009/01/06, 22:20:04 door Vess »

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #20 Gepost op: 2009/01/06, 22:22:58 »
even gekeken wat sox inhoud
http://packages.ubuntu.com/gutsy/sox
kan geen kwaad lijkt me, gewoon doen

en de opdracht
sox -r 32000 -w -t alsa hw:1,0 -t alsa pcm.default &
ik vraag me af of de & er achter hoort, zou het eerst proberen zonder

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #21 Gepost op: 2009/01/06, 22:26:07 »
jurgen@jurgen-desktop:~$ sox -r 32000 -w -t alsa hw:1,0 -t alsa pcm.default
sox soxio: Failed reading `hw:1,0': unknown file type `alsa'

en

jurgen@jurgen-desktop:~$ sox -r 32000 -w -t alsa hw:1,0 -t alsa pcm.default &
[1] 7063
sox soxio: Failed reading `hw:1,0': unknown file type `alsa'
jurgen@jurgen-desktop:~$


Groetjes Jurgen

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #22 Gepost op: 2009/01/06, 22:27:06 »
wel vanuit synaptic installeren, niet downloaden van bovenstaande link

Vess

  • Gast
Re: TV-Kaart installeren
« Reactie #23 Gepost op: 2009/01/06, 22:27:33 »
Heb ik ook gedaan

Offline drik

  • Lid
  • Steunpunt: Nee
Re: TV-Kaart installeren
« Reactie #24 Gepost op: 2009/01/06, 22:28:25 »
probeer
sox -r 32000 -w -t alsa hw:1 -t alsa pcm.default