Alvast bedankt voor de hulp Gijs, ik waardeer dit zeer.
Driver is uitgeschakeld tijdens de installatie. Ik dacht dat via de backports het systeem een stuk minder stabiel kon zijn.
Ik heb de procedure gekopieerd, hij geeft aan dat modules van voorgaande installatie nog aanwezig zijn, dat was bij de eerste poging dus niet zo. Ik ben geen held hierin maar er staan meerdere errors en files not found mijn logisch verstand zegt dan dat het niet helemaal klopt. Vreemd is wel dat het configureren van de draadloze verbinding na onderstaande wel ging en voorheen dus niet. Maar er is dus geen verbinding.
remco@ubuntu:~$ cd madwifi-0.9.4
remco@ubuntu:~/madwifi-0.9.4$ make
Checking requirements... ok.
Checking kernel configuration... ok.
make -C /lib/modules/2.6.27-7-generic/build SUBDIRS=/home/remco/madwifi-0.9.4 modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.27-7-generic'
CC [M] /home/remco/madwifi-0.9.4/net80211/ieee80211_power.o
/home/remco/madwifi-0.9.4/net80211/ieee80211_power.c: In function 'ieee80211_pwrsave':
/home/remco/madwifi-0.9.4/net80211/ieee80211_power.c:240: error: implicit declaration of function '__skb_append'
make[3]: *** [/home/remco/madwifi-0.9.4/net80211/ieee80211_power.o] Error 1
make[2]: *** [/home/remco/madwifi-0.9.4/net80211] Error 2
make[1]: *** [_module_/home/remco/madwifi-0.9.4] Error 2
make[1]: Leaving directory `/usr/src/linux-headers-2.6.27-7-generic'
make: *** [modules] Error 2
remco@ubuntu:~/madwifi-0.9.4$ sudo make install
[sudo] password for remco:
sh scripts/find-madwifi-modules.sh 2.6.27-7-generic
WARNING:
It seems that there are modules left from previous MadWifi installations.
If you are unistalling the MadWifi modules please press "r" to remove them.
If you are installing new MadWifi modules, you should consider removing those
already installed, or else you may experience problems during operation.
Remove old modules?
[l]ist, [r]emove,
gnore or e
r
for i in ath/ ath_hal/ ath_rate/ net80211/; do \
make -C $i install || exit 1; \
done
make[1]: Entering directory `/home/remco/madwifi-0.9.4/ath'
test -d //lib/modules/2.6.27-7-generic/net || mkdir -p //lib/modules/2.6.27-7-generic/net
install ath_pci.ko //lib/modules/2.6.27-7-generic/net
install: cannot stat `ath_pci.ko': No such file or directory
make[1]: *** [install] Error 1
make[1]: Leaving directory `/home/remco/madwifi-0.9.4/ath'
make: *** [install-modules] Error 1
remco@ubuntu:~/madwifi-0.9.4$ sudo modprobe ath_pci
WARNING: Could not open '/lib/modules/2.6.27-7-generic/volatile/ath_hal.ko': No such file or directory
WARNING: Could not open '/lib/modules/2.6.27-7-generic/volatile/wlan.ko': No such file or directory
FATAL: Could not open '/lib/modules/2.6.27-7-generic/volatile/ath_pci.ko': No such file or directory
remco@ubuntu:~/madwifi-0.9.4$ gksudo gedit /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
fuse
lp
ath_pci
Groet, Remco