Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: Hardy: traag opstarten (nummertje zoveel)  (gelezen 1967 keer)

Offline Beryllium

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Gepost op: 2008/05/30, 19:42:16 »
Beste allemaal,

Sinds begin deze maand ben ik van Gutsy naar Hardy over. Hardy bevalt me goed, behalve dat ik (zoals meer mensen) problemen heb met de opstartsnelheid. In eerste instantie leek ik slachtoffer te zijn van de kinit/unable-to-resume bug die vertraging veroorzaakte, maar na wat speurwerk heb ik toch het idee dat het daar niet aan ligt.

De oranje balk blijft bij het laden gauw een 30, 40 seconden heen en weer schieten voordat hij echt gaat booten. Vanaf dan ben ik in Gnome in ongeveer 30 seconden.

Ik heb met bootchart proberen te achterhalen wat er aan de hand is:



En mijn dmesg zegt me het volgende:

maarten@maarten-laptop:~$ dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.24-17-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu May 1 14:31:33 UTC 2008 (Ubuntu 2.6.24-17.31-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d8000 - 00000000000e0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
[    0.000000]  BIOS-e820: 000000003fef0000 - 000000003fefc000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003fefc000 - 000000003ff00000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable)
[    0.000000]  BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000] 127MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 262016) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   262016
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   262016
[    0.000000] On node 0 totalpages: 262016
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 255 pages used for memmap
[    0.000000]   HighMem zone: 32385 pages, LIFO batch:7
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP signature @ 0xC00F6D20 checksum 0
[    0.000000] ACPI: RSDP 000F6D20, 0014 (r0 PTLTD )
[    0.000000] ACPI: RSDT 3FEF64A0, 0028 (r1 PTLTD    RSDT    6040000  LTP        0)
[    0.000000] ACPI: FACP 3FEFBF8C, 0074 (r1 INTEL  845M      6040000 PTL        4B)
[    0.000000] ACPI: DSDT 3FEF64C8, 5AC4 (r1 COMPAL 845M      6040000 MSFT  100000E)
[    0.000000] ACPI: FACS 3FEFCFC0, 0040
[    0.000000] ACPI: DMI detected: Acer
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bfb80000)
[    0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d8000
[    0.000000] swsusp: Registered nosave memory region: 00000000000d8000 - 00000000000e0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 00000000000e4000
[    0.000000] swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259969
[    0.000000] Kernel command line: root=UUID=6c9af076-181f-485c-afd3-9c51cbd7d264 ro quiet splash clocksource=hpet
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] mapped APIC to ffffb000 (0180f000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 2492.708 MHz processor.
[   12.004777] Console: colour VGA+ 80x25
[   12.004782] console [tty0] enabled
[   12.005761] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   12.006709] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   12.044299] Memory: 1026856k/1048064k available (2176k kernel code, 20420k reserved, 1007k data, 368k init, 130496k highmem)
[   12.044311] virtual kernel memory layout:
[   12.044312]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   12.044313]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   12.044314]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   12.044315]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   12.044316]       .init : 0xc0421000 - 0xc047d000   ( 368 kB)
[   12.044317]       .data : 0xc0320134 - 0xc041bdc4   (1007 kB)
[   12.044318]       .text : 0xc0100000 - 0xc0320134   (2176 kB)
[   12.044323] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   12.044403] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   12.124282] Calibrating delay using timer specific routine.. 4990.33 BogoMIPS (lpj=9980676)
[   12.124325] Security Framework initialized
[   12.124339] SELinux:  Disabled at boot.
[   12.124361] AppArmor: AppArmor initialized
[   12.124367] Failure registering capabilities with primary security module.
[   12.124379] Mount-cache hash table entries: 512
[   12.124587] Initializing cgroup subsys ns
[   12.124593] Initializing cgroup subsys cpuacct
[   12.124610] CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00000400 00000000 00000000 00000000
[   12.124626] CPU: Trace cache: 12K uops, L1 D cache: 8K
[   12.124629] CPU: L2 cache: 512K
[   12.124632] CPU: Hyper-Threading is disabled
[   12.124635] CPU: After all inits, caps: bfebf9ff 00000000 00000000 0000b080 00000400 00000000 00000000 00000000
[   12.124651] Compat vDSO mapped to ffffe000.
[   12.124671] Checking 'hlt' instruction... OK.
[   12.140752] SMP alternatives: switching to UP code
[   12.142690] Freeing SMP alternatives: 11k freed
[   12.142856] Early unpacking initramfs... done
[   12.483234] ACPI: Core revision 20070126
[   12.483314] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   12.489557] CPU0: Intel(R) Pentium(R) 4 CPU 2.50GHz stepping 07
[   12.489566] SMP motherboard not detected.
[   12.489569] Local APIC not detected. Using dummy APIC emulation.
[   12.489630] Brought up 1 CPUs
[   12.489654] CPU0 attaching sched-domain:
[   12.489658]  domain 0: span 01
[   12.489660]   groups: 01
[   12.489915] net_namespace: 64 bytes
[   12.489926] Booting paravirtualized kernel on bare hardware
[   12.490535] Time: 17:28:11  Date: 05/30/08
[   12.490572] NET: Registered protocol family 16
[   12.490830] EISA bus registered
[   12.490846] ACPI: bus type pci registered
[   12.510599] PCI: PCI BIOS revision 2.10 entry at 0xfd9a4, last bus=2
[   12.510602] PCI: Using configuration type 1
[   12.510604] Setting up standard PCI resources
[   12.524674] ACPI: EC: Look up EC in DSDT
[   12.528162] ACPI: Interpreter enabled
[   12.528167] ACPI: (supports S0 S3 S4 S5)
[   12.528181] ACPI: Using PIC for interrupt routing
[   12.532733] ACPI: Device [FDDA] status [00000008]: functional but not present; setting present
[   12.533745] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   12.536471] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[   12.536475] ACPI: EC: driver started in interrupt mode
[   12.536526] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   12.536934] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[   12.536939] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[   12.537540] PCI: Transparent bridge - 0000:00:1e.0
[   12.537620] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   12.537669] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[   12.537690] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[   12.540621] ACPI: PCI Interrupt Link [LNKA] (IRQs *9)
[   12.540727] ACPI: PCI Interrupt Link [LNKB] (IRQs *9)
[   12.540830] ACPI: PCI Interrupt Link [LNKC] (IRQs *9)
[   12.540936] ACPI: PCI Interrupt Link [LNKD] (IRQs *9)
[   12.541038] ACPI: PCI Interrupt Link [LNKE] (IRQs *9)
[   12.541130] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[   12.541223] ACPI: PCI Interrupt Link [LNKG] (IRQs 9) *0, disabled.
[   12.541316] ACPI: PCI Interrupt Link [LNKH] (IRQs 9) *0, disabled.
[   12.541454] Linux Plug and Play Support v0.97 (c) Adam Belay
[   12.541494] pnp: PnP ACPI init
[   12.541504] ACPI: bus type pnp registered
[   12.547896] pnp: PnP ACPI: found 12 devices
[   12.547899] ACPI: ACPI bus type pnp unregistered
[   12.547904] PnPBIOS: Disabled by ACPI PNP
[   12.548201] PCI: Using ACPI for IRQ routing
[   12.548205] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   12.567443] NET: Registered protocol family 8
[   12.567446] NET: Registered protocol family 20
[   12.567539] AppArmor: AppArmor Filesystem Enabled
[   12.571424] Time: tsc clocksource has been installed.
[   12.579466] system 00:04: ioport range 0x600-0x60f has been reserved
[   12.579469] system 00:04: ioport range 0x700-0x70f has been reserved
[   12.579472] system 00:04: ioport range 0x1000-0x107f has been reserved
[   12.579475] system 00:04: ioport range 0x1180-0x11bf has been reserved
[   12.579477] system 00:04: ioport range 0x1200-0x120f has been reserved
[   12.579480] system 00:04: ioport range 0xfe00-0xfe01 has been reserved
[   12.579485] system 00:04: iomem range 0xfebffc00-0xfebfffff has been reserved
[   12.579488] system 00:04: iomem range 0xfff80000-0xffffffff could not be reserved
[   12.610000] PCI: Bridge: 0000:00:01.0
[   12.610004]   IO window: 3000-3fff
[   12.610008]   MEM window: e8100000-e81fffff
[   12.610012]   PREFETCH window: f0000000-f7ffffff
[   12.610024] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[   12.610027]   IO window: 00004400-000044ff
[   12.610031]   IO window: 00004800-000048ff
[   12.610036]   PREFETCH window: 54000000-57ffffff
[   12.610040]   MEM window: 58000000-5bffffff
[   12.610044] PCI: Bridge: 0000:00:1e.0
[   12.610048]   IO window: 4000-4fff
[   12.610053]   MEM window: e8200000-e82fffff
[   12.610058]   PREFETCH window: disabled.
[   12.610077] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   12.610335] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
[   12.610339] PCI: setting IRQ 9 as level-triggered
[   12.610342] ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
[   12.610362] NET: Registered protocol family 2
[   12.647392] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   12.647870] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   12.649337] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   12.650282] TCP: Hash tables configured (established 131072 bind 65536)
[   12.650288] TCP reno registered
[   12.659511] checking if image is initramfs... it is
[   13.110416] Switched to high resolution mode on CPU 0
[   13.322301] Freeing initrd memory: 7280k freed
[   13.322947] audit: initializing netlink socket (disabled)
[   13.322969] audit(1212168491.284:1): initialized
[   13.323203] highmem bounce pool size: 64 pages
[   13.325525] VFS: Disk quotas dquot_6.5.1
[   13.325625] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   13.325795] io scheduler noop registered
[   13.325798] io scheduler anticipatory registered
[   13.325800] io scheduler deadline registered
[   13.325815] io scheduler cfq registered (default)
[   13.325879] Boot video device is 0000:01:00.0
[   13.325887] PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
[   13.326275] isapnp: Scanning for PnP cards...
[   13.679829] isapnp: No Plug & Play device found
[   13.716067] Real Time Clock Driver v1.12ac
[   13.716201] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   13.716336] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   13.716509] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   13.717344] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   13.717824] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
[   13.717829] ACPI: PCI Interrupt 0000:00:1f.6[b] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
[   13.717839] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[   13.718640] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   13.718723] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   13.718864] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[   13.722585] i8042.c: Detected active multiplexing controller, rev 1.1.
[   13.725342] serio: i8042 KBD port at 0x60,0x64 irq 1
[   13.725348] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   13.725351] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   13.725353] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   13.725356] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   13.737188] mice: PS/2 mouse device common for all mice
[   13.737342] EISA: Probing bus 0 at eisa.0
[   13.737352] Cannot allocate resource for EISA slot 1
[   13.737355] Cannot allocate resource for EISA slot 2
[   13.737357] Cannot allocate resource for EISA slot 3
[   13.737359] Cannot allocate resource for EISA slot 4
[   13.737376] EISA: Detected 0 cards.
[   13.737380] cpuidle: using governor ladder
[   13.737382] cpuidle: using governor menu
[   13.737501] NET: Registered protocol family 1
[   13.737536] Using IPI No-Shortcut mode
[   13.737581] registered taskstats version 1
[   13.737690]   Magic number: 8:976:492
[   13.737847] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   13.737849] EDD information not available.
[   13.738403] Freeing unused kernel memory: 368k freed
[   13.765123] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   15.057466] fuse init (API version 7.9)
[   15.083365] ACPI: CPU0 (power states: C1[C1] C2[C2])
[   15.083373] ACPI: Processor [CPU0] (supports 8 throttling states)
[   15.913722] usbcore: registered new interface driver usbfs
[   15.913756] usbcore: registered new interface driver hub
[   15.925382] usbcore: registered new device driver usb
[   15.989337] SCSI subsystem initialized
[   16.002030] USB Universal Host Controller Interface driver v3.0
[   16.002122] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
[   16.002138] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   16.002143] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   16.002590] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   16.002622] uhci_hcd 0000:00:1d.0: irq 9, io base 0x00001860
[   16.002800] usb usb1: configuration #1 chosen from 1 choice
[   16.002830] hub 1-0:1.0: USB hub found
[   16.002837] hub 1-0:1.0: 2 ports detected
[   16.088423] libata version 3.00 loaded.
[   16.100464] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[   16.100469] e100: Copyright(c) 1999-2006 Intel Corporation
[   16.105796] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
[   16.105803] ACPI: PCI Interrupt 0000:00:1d.1[b] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
[   16.105817] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   16.105822] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   16.105854] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   16.105882] uhci_hcd 0000:00:1d.1: irq 9, io base 0x000018c0
[   16.106022] usb usb2: configuration #1 chosen from 1 choice
[   16.106055] hub 2-0:1.0: USB hub found
[   16.106064] hub 2-0:1.0: 2 ports detected
[   16.208545] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
[   16.208552] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
[   16.208565] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   16.208570] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   16.208607] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   16.208635] uhci_hcd 0000:00:1d.2: irq 9, io base 0x00001800
[   16.208777] usb usb3: configuration #1 chosen from 1 choice
[   16.208814] hub 3-0:1.0: USB hub found
[   16.208822] hub 3-0:1.0: 2 ports detected
[   16.299739] FDC 0 is a post-1991 82077
[   16.312541] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 9
[   16.312547] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKE] -> GSI 9 (level, low) -> IRQ 9
[   16.337944] e100: eth0: e100_probe: addr 0xe8205000, irq 9, MAC addr 00:02:3f:b4:24:a9
[   16.338006] PCI: Enabling device 0000:02:00.0 (0110 -> 0112)
[   16.338016] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
[   16.387761] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[9]  MMIO=[e8204000-e82047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[   16.409533] ata_piix 0000:00:1f.1: version 2.12
[   16.409557] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[   16.409569] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
[   16.409631] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   16.411245] scsi0 : ata_piix
[   16.411350] scsi1 : ata_piix
[   16.412389] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1820 irq 14
[   16.412392] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1828 irq 15
[   16.576016] ata1.00: ATA-6: HTS721080G9AT00, MC4OA51A, max UDMA/100
[   16.576022] ata1.00: 156301488 sectors, multi 16: LBA48
[   16.591949] ata1.00: configured for UDMA/100
[   16.747420] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x1)
[   16.747426] ata2: failed to recover some devices, retrying in 5 secs
[   17.677396] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f2c26000337]
[   21.897084] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x1)
[   21.897091] ata2: failed to recover some devices, retrying in 5 secs
[   27.046785] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x1)
[   27.046791] ata2: failed to recover some devices, retrying in 5 secs
[   32.360146] ata2.00: ATAPI: QSI CD-RW/DVD-ROM SBW-161, SX13, max UDMA/33
[   32.523762] ata2.00: configured for UDMA/33
[   32.523929] scsi 0:0:0:0: Direct-Access     ATA      HTS721080G9AT00  MC4O PQ: 0 ANSI: 5
[   32.525060] scsi 1:0:0:0: CD-ROM            QSI      DVD/CDRW SBW-161 SX13 PQ: 0 ANSI: 5
[   32.545487] Driver 'sd' needs updating - please use bus_type methods
[   32.545613] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[   32.545631] sd 0:0:0:0: [sda] Write Protect is off
[   32.545635] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   32.545660] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   32.545722] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[   32.545736] sd 0:0:0:0: [sda] Write Protect is off
[   32.545739] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   32.545762] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   32.545767]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[   32.879213]  sda1 sda2 < sda5 sda6 >
[   32.911002] sd 0:0:0:0: [sda] Attached SCSI disk
[   32.920400] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   32.920428] sr 1:0:0:0: Attached scsi generic sg1 type 5
[   32.922304] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[   32.922311] Uniform CD-ROM driver Revision: 3.20
[   32.922382] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   33.197866] kjournald starting.  Commit interval 5 seconds
[   33.197887] EXT3-fs: mounted filesystem with ordered data mode.
[   42.775325] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   42.850919] iTCO_vendor_support: vendor-support=0
[   42.910702] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   42.910888] iTCO_wdt: Found a ICH3-M TCO device (Version=1, TCOBASE=0x1060)
[   42.910941] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   42.967587] Linux agpgart interface v0.102
[   43.022552] agpgart: Detected an Intel 845G Chipset.
[   43.026248] agpgart: AGP aperture is 64M @ 0xec000000
[   43.066485] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   43.186256] input: PC Speaker as /devices/platform/pcspkr/input/input2
[   43.317870] intel_rng: FWH not detected
[   43.570255] input: Power Button (FF) as /devices/virtual/input/input3
[   43.581438] ACPI: Power Button (FF) [PWRF]
[   43.581645] input: Lid Switch as /devices/virtual/input/input4
[   43.581732] ACPI: Lid Switch [LID]
[   43.581813] input: Power Button (CM) as /devices/virtual/input/input5
[   43.597296] ACPI: Power Button (CM) [PWRB]
[   43.597458] input: Sleep Button (CM) as /devices/virtual/input/input6
[   43.613285] ACPI: Sleep Button (CM) [SLPB]
[   44.220165] irda_init()
[   44.220196] NET: Registered protocol family 23
[   44.352069] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
[   44.383926] ACPI: AC Adapter [ACAD] (on-line)
[   44.391840] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[   44.410552] found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227
[   44.410572] smsc_superio_flat(): fir: 0x6f8, sir: 0x2f8, dma: 03, irq: 3, mode: 0x0e
[   44.410579] smsc_ircc_present: can't get sir_base of 0x2f8
[   45.003156] ACPI: Battery Slot [BAT1] (battery present)
[   45.642402] Yenta: CardBus bridge found at 0000:02:04.0 [1025:001e]
[   45.642428] Yenta O2: res at 0x94/0xD4: 00/ea
[   45.642430] Yenta O2: enabling read prefetch/write burst
[   45.769887] Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
[   45.769894] Socket status: 30000811
[   45.769898] Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
[   45.769905] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
[   45.769909] cs: IO port probe 0x4000-0x4fff: clean.
[   45.770143] pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
[   46.172970] ACPI: PCI Interrupt 0000:00:1f.5[b] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
[   46.172992] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   46.191606] ACPI: WMI-Acer: Mapper loaded
[   46.206655] wbsd: Winbond W83L51xD SD/MMC card interface driver
[   46.206660] wbsd: Copyright(c) Pierre Ossman
[   46.207275] wbsd 00:0a: activated
[   46.212602] mmc0: W83L51xD id 7112 at 0x248 irq 10 FIFO PnP
[   46.261844] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[   46.261862] acer_acpi: No or unsupported WMI interface, unable to load.
[   46.447607] pccard: PCMCIA card inserted into slot 0
[   46.747018] intel8x0_measure_ac97_clock: measured 55400 usecs
[   46.747023] intel8x0: clocking to 48000
[   48.479506] cs: memory probe 0xe8200000-0xe82fffff: excluding 0xe8200000-0xe820ffff
[   48.499268] pcmcia: registering new device pcmcia0.0
[   48.543692] cs: IO port probe 0x100-0x3af: excluding 0x200-0x20f
[   48.545589] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   48.546402] cs: IO port probe 0x820-0x8ff: clean.
[   48.547092] cs: IO port probe 0xc00-0xcf7: clean.
[   48.547995] cs: IO port probe 0xa00-0xaff: clean.
[   49.148958] eth1: Atmel at76c50x. Version 0.98. MAC 00:60:b3:77:88:c0
[   49.535303] lp: driver loaded but no devices found
[   49.852805] Adding 4907816k swap on /dev/sda6.  Priority:-1 extents:1 across:4907816k
[   50.197545] EXT3 FS on sda1, internal journal
[   50.858408] kjournald starting.  Commit interval 5 seconds
[   50.858673] EXT3 FS on sda5, internal journal
[   50.858679] EXT3-fs: mounted filesystem with ordered data mode.
[   51.413463] ip_tables: (C) 2000-2006 Netfilter Core Team
[   52.283140] No dock devices found.
[   52.405050] ACPI: \_SB_.PCI0.IDEC.SECD.S_D0: found ejectable bay
[   52.405056] ACPI: \_SB_.PCI0.IDEC.SECD.S_D0: Adding notify handler
[   52.405103] ACPI: Error installing bay notify handler
[   52.405107] ACPI: Bay [\_SB_.PCI0.IDEC.SECD.S_D0] Added
[   53.665179] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   53.665188] apm: overridden by ACPI.
[   53.814935] ppdev: user-space parallel port driver
[   53.950455] audit(1212168532.582:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=7587 profile="/usr/sbin/cupsd" namespace="default"
[   56.025872] [drm] Initialized drm 1.1.0 20060810
[   56.033037] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
[   56.033655] [drm] Initialized radeon 1.28.0 20060524 on minor 0
[   58.360282] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[   58.360306] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[   58.360329] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[   59.842210] [drm] Setting GART location based on new memory map
[   59.842279] [drm] writeback test succeeded in 2 usecs
[   71.439287] NET: Registered protocol family 10
[   71.439938] lo: Disabled Privacy Extensions
[   71.440733] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   71.441258] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   79.316447] NET: Registered protocol family 17
[   81.400705] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   99.074126] eth1: no IPv6 routers present
Hij hangt verschillende keren zo telkens 5 seconden.

Wie heeft een idee dat mij verder kan helpen?

Offline Jan E.

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #1 Gepost op: 2008/05/30, 19:50:24 »
Hoi Beryllium, ben momenteel niet in de gelegenheid het precies op te zoeken, maar het zit hem volgens mij in de resolutie van je bootsplash. Als je PC moeite heeft met de resolutie, duurt het eerste deel van het opstarten erg lang. Had ik hier ook op een laptop. In een config bestandje de resolutie vast gezet op de juiste resolutie en het probleem was verholpen.


Samsung NP300E7A
Ubuntu 14.04


Offline Beryllium

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #3 Gepost op: 2008/05/30, 21:03:50 »
Hoi Pjotr,

Dank voor de tip, maar ik was vergeten te melden dat ik dat al gedaan had.
Dit is mijn menu.lst:

# menu.lst - See: grub(8), info grub, update-grub(8)
#            grub-install(8), grub-floppy(8),
#            grub-md5-crypt, /usr/share/doc/grub
#            and /usr/share/doc/grub-doc/.

## default num
# Set the default entry to the entry number NUM. Numbering starts from 0, and
# the entry number 0 is the default if the command is not used.
#
# You can specify 'saved' instead of a number. In this case, the default entry
# is the entry saved with the command 'savedefault'.
# WARNING: If you are using dmraid do not use 'savedefault' or your
# array will desync and will not let you boot your system.
default 0

## timeout sec
# Set a timeout, in SEC seconds, before automatically booting the default entry
# (normally the first entry defined).
timeout 3

## hiddenmenu
# Hides the menu by default (press ESC to see the menu)
hiddenmenu

# Pretty colours
#color cyan/blue white/blue

## password ['--md5'] passwd
# If used in the first section of a menu file, disable all interactive editing
# control (menu entry editor and command-line)  and entries protected by the
# command 'lock'
# e.g. password topsecret
#      password --md5 $1$gLhU0/$aW78kHK1QfV3P2b2znUoe/
# password topsecret

#
# examples
#
# title Windows 95/98/NT/2000
# root (hd0,0)
# makeactive
# chainloader +1
#
# title Linux
# root (hd0,1)
# kernel /vmlinuz root=/dev/hda2 ro
#

#
# Put static boot stanzas before and/or after AUTOMAGIC KERNEL LIST

### BEGIN AUTOMAGIC KERNELS LIST
## lines between the AUTOMAGIC KERNELS LIST markers will be modified
## by the debian update-grub script except for the default options below

## DO NOT UNCOMMENT THEM, Just edit them to your needs

## ## Start Default Options ##
## default kernel options
## default kernel options for automagic boot options
## If you want special options for specific kernels use kopt_x_y_z
## where x.y.z is kernel version. Minor versions can be omitted.
## e.g. kopt=root=/dev/hda1 ro
##      kopt_2_6_8=root=/dev/hdc1 ro
##      kopt_2_6_8_2_686=root=/dev/hdc2 ro
# kopt=root=UUID=6c9af076-181f-485c-afd3-9c51cbd7d264 ro

## Setup crashdump menu entries
## e.g. crashdump=1
# crashdump=0

## default grub root device
## e.g. groot=(hd0,0)
# groot=(hd0,0)

## should update-grub create alternative automagic boot options
## e.g. alternative=true
##      alternative=false
# alternative=true

## should update-grub lock alternative automagic boot options
## e.g. lockalternative=true
##      lockalternative=false
# lockalternative=false

## additional options to use with the default boot option, but not with the
## alternatives
## e.g. defoptions=vga=791 resume=/dev/hda5
# defoptions=quiet splash clocksource=hpet

## should update-grub lock old automagic boot options
## e.g. lockold=false
##      lockold=true
# lockold=false

## Xen hypervisor options to use with the default Xen boot option
# xenhopt=

## Xen Linux kernel options to use with the default Xen boot option
# xenkopt=console=tty0

## altoption boot targets option
## multiple altoptions lines are allowed
## e.g. altoptions=(extra menu suffix) extra boot options
##      altoptions=(recovery) single
# altoptions=(recovery mode) single

## controls how many kernels should be put into the menu.lst
## only counts the first occurence of a kernel, not the
## alternative kernel options
## e.g. howmany=all
##      howmany=7
# howmany=all

## should update-grub create memtest86 boot option
## e.g. memtest86=true
##      memtest86=false
# memtest86=true

## should update-grub adjust the value of the default booted system
## can be true or false
# updatedefaultentry=false

## should update-grub add savedefault to the default options
## can be true or false
# savedefault=false

## ## End Default Options ##

title Ubuntu 8.04, kernel 2.6.24-17-generic
root (hd0,0)
kernel /boot/vmlinuz-2.6.24-17-generic root=UUID=6c9af076-181f-485c-afd3-9c51cbd7d264 ro quiet splash clocksource=hpet
initrd /boot/initrd.img-2.6.24-17-generic
quiet

title Ubuntu 8.04, kernel 2.6.24-17-generic (recovery mode)
root (hd0,0)
kernel /boot/vmlinuz-2.6.24-17-generic root=UUID=6c9af076-181f-485c-afd3-9c51cbd7d264 ro single
initrd /boot/initrd.img-2.6.24-17-generic

title Ubuntu 8.04, kernel 2.6.24-16-generic
root (hd0,0)
kernel /boot/vmlinuz-2.6.24-16-generic root=UUID=6c9af076-181f-485c-afd3-9c51cbd7d264 ro quiet splash clocksource=hpet
initrd /boot/initrd.img-2.6.24-16-generic
quiet

title Ubuntu 8.04, kernel 2.6.24-16-generic (recovery mode)
root (hd0,0)
kernel /boot/vmlinuz-2.6.24-16-generic root=UUID=6c9af076-181f-485c-afd3-9c51cbd7d264 ro single
initrd /boot/initrd.img-2.6.24-16-generic

title Ubuntu 8.04, memtest86+
root (hd0,0)
kernel /boot/memtest86+.bin
quiet

### END DEBIAN AUTOMAGIC KERNELS LIST
Klopt toch neem ik aan?

@Asterix: bedankt, maar dat is het denk ik niet. Hij staat al op 1024x768, dat is de max, resolutie van mijn laptop.
Of bedoel je juist dat ik hem op 800x600 o.i.d. moet zetten?

Offline Pjotr

  • Lid
    • http://sites.google.com/site/computertip
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #4 Gepost op: 2008/05/30, 23:57:25 »
Weet je zeker, dat je ook sudo update-grub hebt gedaan?

Offline Gandyman

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #5 Gepost op: 2008/05/31, 02:20:16 »
Je kan ook nog tekstmode aanvinken in de opstart manager, dan zie je stap voor stap waar hij druk mee is..
I don't suffer from insanity, I enjoy every minute of it.
Microsoft geeft je een raam, Linux geeft je een heel huis :D

Offline Beryllium

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #6 Gepost op: 2008/05/31, 11:35:22 »
Die sudo update-grub had ik gedaan dacht ik, probeer het nog eens.
[edit]: nog eens geprobeerd, helaas geen verbetering :(

@Gandyman: da's het rare, hij blijft hangen op de tekst 'Loading please wait...' en na een tijdje verschijnt de mededeling 'loading files for boot [OK]'.
Ik kan dus niet echt achterhalen waarom hij nou ergens blijft steken.

Offline Maarten123

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #7 Gepost op: 2008/05/31, 12:04:08 »
Ik had ook problemen met opstarten (traag.) nadat ik een Live CD had gebruikt en de tips van Pjotr123.
Nadat ik een verse installatie deed met de alternate CD heb ik geen problemen meer.
Oorzaak... ?
Werkt in ieder geval wel

Offline lizardman

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #8 Gepost op: 2008/05/31, 12:35:17 »
Aan je dmesg te zien heeft ie moeite met ata2
Citaat
16.747420] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x1)
[   16.747426] ata2: failed to recover some devices, retrying in 5 secs
[   17.677396] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f2c26000337]
[   21.897084] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x1)
[   21.897091] ata2: failed to recover some devices, retrying in 5 secs
[   27.046785] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x1)
[   27.046791] ata2: failed to recover some devices, retrying in 5 secs
[   32.360146] ata2.00: ATAPI: QSI CD-RW/DVD-ROM SBW-161, SX13, max UDMA/33
[   32.523762] ata2.00: configured for UDMA/33
dat verklaart in ieder geval de 5sec delay waar je het over had.

wat eraan te doen weet ik (nog?) niet..

*edit* koppel de CD-RW/DVD-ROM eens los en kijk of ie dan sneller boot?
"Het is een teken van een ontwikkelde geest om met een gedachte te kunnen spelen zonder die te accepteren."

Aristoteles Grieks filosoof (384 v.C. - 322 v.C.)

Offline ShadowDragon

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #9 Gepost op: 2008/05/31, 15:11:09 »
Ik sluit mij aan bij de uitspraak van lizardman, er gaat iets mis met het herkennen van je CD/DVD-rom drive...

Dit kan je op de volgende manier zien in je bootchart afbeelding:

De eerste tijdmeting die je vindt in je dmesg is "12.004777".
ATA2 wordt benaderd op tijdstip "16.747420", of m.a.w. +/- 4.75 seconden na het opstarten. (*1)
ATA2 wordt herkent op tijdstip "32.360146", of m.a.w. +/- 20.35 seconden na het opstarten. (*2)

Als je nu gaat kijken in je afbeelding van bootchart dan vind je bijna helemaal onderaan "scs1_eh_1" terug. Het balkje van "scs1_eh_1" is voor een stuk rood/roze gekleurd, beginnend rond iets na 4 seconden (*1) en eindigend na iets van een 20 seconden (*2)
Ook "modprobe" bovenaan de lijst komt hier sterk mee overeen.

Misschien levert wat googlen op termen met "scs1_eh_1" "CD/DVD-rom drive" "modprobe" wat op...
Neem misschien ook eens een kijkje op Launchpad's ubuntu...
Xubuntu 11.04 - Xfce 4.8 - SSD Vertex 2 (Extended) 60 GB

Offline Beryllium

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #10 Gepost op: 2008/05/31, 16:19:12 »
Bedankt voor de reacties!

Ik heb mijn CD-drive losgekoppeld en ben inderdaad af van dat heen-en-weer schietende balkje. Ok is de boot nu merkbaar vlotter.
Alleen werken mijn laptop hotkeys weer niet als ik de drive eruit laat ???
Nou ja, hoe dan ook, opstarten zonder CD/DVD is ook niet handig.

Misschien zijn er ergens andere instellingen die ik kan tweaken? Googelen op "scs1_eh_1" levert nul hits, en ik weet niet goed waar ik verder op kan letten.

Overigens, mijn CD/DVD werkt prima, dus daar zal het wel niet aan liggen, hij is niet kapot o.i.d.

Offline lizardman

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #11 Gepost op: 2008/05/31, 20:09:01 »
Je zou eens kunnen kijken of de CD-drive wel als 'master' staat ingesteld en niet als 'slave' of 'cable select'.

google eens op: ata2.00: configured for UDMA/33  of een van de andere foutmeldingen uit je dmesg?
"Het is een teken van een ontwikkelde geest om met een gedachte te kunnen spelen zonder die te accepteren."

Aristoteles Grieks filosoof (384 v.C. - 322 v.C.)

Offline Gandyman

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #12 Gepost op: 2008/05/31, 20:18:03 »
Is die drive wel leeg ??
Of heb je er een cdtje of dvdtje inzitten ??

Zoja haal die er dan uit....
I don't suffer from insanity, I enjoy every minute of it.
Microsoft geeft je een raam, Linux geeft je een heel huis :D

Offline Beryllium

  • Lid
  • Steunpunt: Nee
Hardy: traag opstarten (nummertje zoveel)
« Reactie #13 Gepost op: 2008/06/01, 12:25:15 »
Er zit standaard geen CD in, maar ook met een CD erin doet hij dit.
Ik kan hem niet als master/slave instellen, hij zit in een laptop en daar heb ik geen configuratiemogelijkheden. De harddrive is IDE1, master en de CD/DVD is IDE2/master.

Ik ga nog even googlen op foutmeldingen.