Nieuws:

We zijn er weer.

Na lange tijd van afwezigheid zijn we er weer  :laugh:
We hebben alle wachtwoorden gereset, je oude wachtwoord werkt niet meer.Je moet via het "wachtwoord vergeten"-linkje je wachtwoord resetten. Je krijgt hiervoor een mailtje op het adres dat je bij ons geregistreerd hebt.

De komende tijd zijn we nog druk bezig om de rest van de site op te bouwen, dus het kan zijn dat sommige onderdelen (tijdelijk) niet werken.

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: Heb problemen met intel wifi kaart  (gelezen 5257 keer)

philiper

  • Gast
Heb problemen met intel wifi kaart
« Gepost op: 2008/04/26, 12:29:42 »
Ik heb een probleem met mijn wifi kaart sinds ik geupgrade van ubuntu 7.10 naar 8.04. Ik kan thuis geen verbinding maken met mijn router maar op school maakt hij wel verbinding met een acces point. Licht niet aan de router want andere laptop en playstation geraken er wel op.

Offline siegi

  • Lid
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #1 Gepost op: 2008/04/26, 12:56:01 »
Klik rechtboven op het netwerkicoontje krijg je dan een lijst van beschikbare netwerken?

philiper

  • Gast
Heb problemen met intel wifi kaart
« Reactie #2 Gepost op: 2008/04/27, 09:51:26 »
Ja dat doet ie allemaal perfect hij vraagt zelfs mijn wpa code maar hij probeerte thuis verbinding te maken maar dat lukt niet.

Offline siegi

  • Lid
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #3 Gepost op: 2008/04/27, 17:00:33 »
Welke beveiliging heb je dan op school?

philiper

  • Gast
Heb problemen met intel wifi kaart
« Reactie #4 Gepost op: 2008/04/27, 22:08:07 »
Op school hebben we geen beveiliging maar ik heb thuis ook al geprobeert zonder beveiliging en met wep maar hij wilt thuis gewoon geen verbinding maken

Offline G. Schrijvers

  • Lid
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #5 Gepost op: 2008/04/27, 22:16:34 »
Ik heb ook een probleem met mijn wireless card. Ik heb het ondertussen op launchepad gezet en er blijken nog mensen te zijn die problemen hebben met dezelfde kaart. Ik heb een 3945ABG Network kaart van Intel.

Grtz GGS1988
Grtz GGS1988

Laptop: Packard Bell: Easynote MX 65 100    :   Debian Edge (32-bit) (Test-server)
Laptop: Dell XPS 1530                               :   Ubuntu 8.10 (64-bit)
Desktop: AMD 6000, HD3870, 4GB DDR2        :   Ubuntu 8.04 (64-bit)

philiper

  • Gast
Heb problemen met intel wifi kaart
« Reactie #6 Gepost op: 2008/04/28, 16:49:27 »
Ja ik denk dat het die kaart is. Ik ben niet zeker want ik heb de doos niet meer.

Offline profoX

  • Lid
    • wesley
    • Lionslink
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #7 Gepost op: 2008/04/29, 14:11:44 »
syslog
[    0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
[    0.000000]  BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[    0.000000] 127MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000ff780
[    0.000000] Entering add_active_range(0, 0, 262096) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   262096
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   262096
[    0.000000] On node 0 totalpages: 262096
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 255 pages used for memmap
[    0.000000]   HighMem zone: 32465 pages, LIFO batch:7
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F7BB0 checksum 0
[    0.000000] ACPI: RSDP 000F7BB0, 0014 (r0 ACPIAM)
[    0.000000] ACPI: RSDT 3FFD0000, 003C (r1 AMI    OEMRSDT  10000604 MSFT       97)
[    0.000000] ACPI: FACP 3FFD0200, 0084 (r2 AMI    OEMFACP  10000604 MSFT       97)
[    0.000000] ACPI: DSDT 3FFD0460, 7BC6 (r1  A6JC0 A6JC0220      220 INTL  2002026)
[    0.000000] ACPI: FACS 3FFDE000, 0040
[    0.000000] ACPI: APIC 3FFD0390, 005C (r1 AMI    OEMAPIC  10000604 MSFT       97)
[    0.000000] ACPI: MCFG 3FFD03F0, 003C (r1 AMI    OEMMCFG  10000604 MSFT       97)
[    0.000000] ACPI: BOOT 3FFD0430, 0028 (r1 AMI    OEMBOOT  10000604 MSFT       97)
[    0.000000] ACPI: OEMB 3FFDE040, 0046 (r1 AMI    AMI_OEM  10000604 MSFT       97)
[    0.000000] ACPI: SSDT 3FFD8030, 0C60 (r1    AMI   CPU1PM        1 INTL 20051117)
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:14 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bee00000)
[    0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260049
[    0.000000] Kernel command line: root=UUID=9faa0d06-a4a9-4653-9d75-7f72d0d58499 ro quiet splash locale=nl_NL
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 1862.050 MHz processor.
[   12.644437] Console: colour VGA+ 80x25
[   12.644444] console [tty0] enabled
[   12.644773] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   12.645433] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   12.698902] Memory: 1027280k/1048384k available (2157k kernel code, 20384k reserved, 998k data, 364k init, 130880k highmem)
[   12.698918] virtual kernel memory layout:
[   12.698920]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   12.698923]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   12.698926]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   12.698929]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   12.698931]       .init : 0xc041b000 - 0xc0476000   ( 364 kB)
[   12.698934]       .data : 0xc031b5a4 - 0xc0414dc4   ( 998 kB)
[   12.698937]       .text : 0xc0100000 - 0xc031b5a4   (2157 kB)
[   12.698944] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   12.699002] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   12.778899] Calibrating delay using timer specific routine.. 3729.21 BogoMIPS (lpj=7458437)
[   12.778939] Security Framework initialized
[   12.778949] SELinux:  Disabled at boot.
[   12.778973] AppArmor: AppArmor initialized
[   12.778981] Failure registering capabilities with primary security module.
[   12.778996] Mount-cache hash table entries: 512
[   12.779198] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 00000000
[   12.779216] monitor/mwait feature present.
[   12.779220] using mwait in idle threads.
[   12.779227] CPU: L1 I cache: 32K, L1 D cache: 32K
[   12.779232] CPU: L2 cache: 2048K
[   12.779238] CPU: After all inits, caps: afe9fbff 00100000 00000000 00002940 0000c189 00000000 00000000 00000000
[   12.779255] Compat vDSO mapped to ffffe000.
[   12.779277] Checking 'hlt' instruction... OK.
[   12.795606] SMP alternatives: switching to UP code
[   12.798999] Freeing SMP alternatives: 11k freed
[   12.799198] Early unpacking initramfs... done
[   13.550033] ACPI: Core revision 20070126
[   13.550173] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   13.570839] CPU0: Intel Genuine Intel(R) CPU           T1350  @ 1.86GHz stepping 08
[   13.570881] Total of 1 processors activated (3729.21 BogoMIPS).
[   13.571062] ENABLING IO-APIC IRQs
[   13.571278] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   13.717420] Brought up 1 CPUs
[   13.717456] CPU0 attaching sched-domain:
[   13.717461]  domain 0: span 01
[   13.717465]   groups: 01
[   13.717748] net_namespace: 64 bytes
[   13.717768] Booting paravirtualized kernel on bare hardware
[   13.718720] Time: 11:58:05  Date: 04/29/08
[   13.718760] NET: Registered protocol family 16
[   13.719146] EISA bus registered
[   13.719178] ACPI: bus type pci registered
[   13.719560] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[   13.719565] PCI: Using configuration type 1
[   13.719568] Setting up standard PCI resources
[   13.727496] ACPI: EC: Look up EC in DSDT
[   13.791963] ACPI: Interpreter enabled
[   13.791970] ACPI: (supports S0 S1 S3 S4 S5)
[   13.792009] ACPI: Using IOAPIC for interrupt routing
[   13.808306] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[   13.808312] ACPI: EC: driver started in poll mode
[   13.808567] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   13.809509] Force enabled HPET at base address 0xfed00000
[   13.809519] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[   13.809527] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[   13.810934] PCI: Transparent bridge - 0000:00:1e.0
[   13.811077] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   13.811439] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[   13.811672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[   13.811973] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[   13.812231] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[   13.836297] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
[   13.836622] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 12)
[   13.836943] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 12)
[   13.837273] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 12)
[   13.837594] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 12) *0, disabled.
[   13.837916] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 12)
[   13.838243] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 12)
[   13.838569] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 12)
[   13.838872] ACPI: Power Resource [GFAN] (off)
[   13.838958] Linux Plug and Play Support v0.97 (c) Adam Belay
[   13.839027] pnp: PnP ACPI init
[   13.839040] ACPI: bus type pnp registered
[   13.843856] pnp: PnP ACPI: found 14 devices
[   13.843861] ACPI: ACPI bus type pnp unregistered
[   13.843869] PnPBIOS: Disabled by ACPI PNP
[   13.844312] PCI: Using ACPI for IRQ routing
[   13.844317] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   13.877093] NET: Registered protocol family 8
[   13.877097] NET: Registered protocol family 20
[   13.877277] hpet clockevent registered
[   13.877286] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   13.877295] hpet0: 3 64-bit timers, 14318180 Hz
[   13.878349] AppArmor: AppArmor Filesystem Enabled
[   13.881072] Time: tsc clocksource has been installed.
[   13.889135] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[   13.889154] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[   13.889160] system 00:08: ioport range 0x800-0x87f has been reserved
[   13.889166] system 00:08: ioport range 0x480-0x4bf has been reserved
[   13.889173] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[   13.889180] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
[   13.889191] system 00:09: iomem range 0xffb80000-0xffbfffff could not be reserved
[   13.889198] system 00:09: iomem range 0xfff80000-0xffffffff could not be reserved
[   13.889209] system 00:0a: iomem range 0xffc00000-0xfff7ffff could not be reserved
[   13.889220] system 00:0b: ioport range 0x400-0x41f has been reserved
[   13.889227] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[   13.889234] system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[   13.889240] system 00:0b: iomem range 0xfec10000-0xfec17fff has been reserved
[   13.889247] system 00:0b: iomem range 0xfec28000-0xfec2ffff has been reserved
[   13.889258] system 00:0c: iomem range 0xe0000000-0xe3ffffff has been reserved
[   13.889270] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[   13.889276] system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
[   13.889282] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[   13.889289] system 00:0d: iomem range 0x100000-0x3fffffff could not be reserved
[   13.889295] system 00:0d: iomem range 0x0-0x0 could not be reserved
[   13.920064] PCI: Bridge: 0000:00:01.0
[   13.920068]   IO window: disabled.
[   13.920075]   MEM window: f9f00000-fdffffff
[   13.920081]   PREFETCH window: bdf00000-ddefffff
[   13.920088] PCI: Bridge: 0000:00:1c.0
[   13.920093]   IO window: c000-cfff
[   13.920101]   MEM window: fe000000-fe0fffff
[   13.920108]   PREFETCH window: disabled.
[   13.920116] PCI: Bridge: 0000:00:1c.3
[   13.920119]   IO window: disabled.
[   13.920127]   MEM window: fe100000-fe1fffff
[   13.920133]   PREFETCH window: disabled.
[   13.920153] PCI: Bus 5, cardbus bridge: 0000:04:01.0
[   13.920158]   IO window: 0000d000-0000d0ff
[   13.920165]   IO window: 0000d400-0000d4ff
[   13.920173]   PREFETCH window: 50000000-53ffffff
[   13.920180]   MEM window: 54000000-57ffffff
[   13.920187] PCI: Bridge: 0000:00:1e.0
[   13.920192]   IO window: d000-dfff
[   13.920201]   MEM window: fe200000-feafffff
[   13.920208]   PREFETCH window: ddf00000-dfefffff
[   13.920235] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[   13.920246] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   13.920275] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[   13.920286] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   13.920316] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 17
[   13.920326] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[   13.920344] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   13.920366] ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 18
[   13.920390] NET: Registered protocol family 2
[   13.957050] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   13.957477] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   13.958976] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   13.959722] TCP: Hash tables configured (established 131072 bind 65536)
[   13.959727] TCP reno registered
[   13.969165] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[   14.692776]  it is
[   15.448626] Freeing initrd memory: 7282k freed
[   15.448868] Simple Boot Flag at 0x52 set to 0x1
[   15.449828] audit: initializing netlink socket (disabled)
[   15.449849] audit(1209470286.588:1): initialized
[   15.450121] highmem bounce pool size: 64 pages
[   15.454004] VFS: Disk quotas dquot_6.5.1
[   15.454151] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   15.454416] io scheduler noop registered
[   15.454421] io scheduler anticipatory registered
[   15.454425] io scheduler deadline registered
[   15.454448] io scheduler cfq registered (default)
[   15.454567] Boot video device is 0000:01:00.0
[   15.454768] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   15.454829] assign_interrupt_mode Found MSI capability
[   15.454879] Allocate Port Service[0000:00:01.0:pcie00]
[   15.455019] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   15.455087] assign_interrupt_mode Found MSI capability
[   15.455142] Allocate Port Service[0000:00:1c.0:pcie00]
[   15.455210] Allocate Port Service[0000:00:1c.0:pcie02]
[   15.455356] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[   15.455424] assign_interrupt_mode Found MSI capability
[   15.455479] Allocate Port Service[0000:00:1c.3:pcie00]
[   15.455548] Allocate Port Service[0000:00:1c.3:pcie02]
[   15.455997] isapnp: Scanning for PnP cards...
[   15.810550] isapnp: No Plug & Play device found
[   15.866288] Real Time Clock Driver v1.12ac
[   15.866470] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   15.868823] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   15.868953] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   15.869135] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[   15.872223] i8042.c: Detected active multiplexing controller, rev 1.1.
[   15.873386] serio: i8042 KBD port at 0x60,0x64 irq 1
[   15.873394] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   15.873400] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   15.873405] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   15.873410] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   15.881666] mice: PS/2 mouse device common for all mice
[   15.881887] EISA: Probing bus 0 at eisa.0
[   15.881932] EISA: Detected 0 cards.
[   15.881938] cpuidle: using governor ladder
[   15.881942] cpuidle: using governor menu
[   15.882096] NET: Registered protocol family 1
[   15.882140] Using IPI No-Shortcut mode
[   15.882184] registered taskstats version 1
[   15.882355]   Magic number: 4:774:985
[   15.882466] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   15.882470] EDD information not available.
[   15.882714] Freeing unused kernel memory: 364k freed
[   15.917494] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   17.334430] fuse init (API version 7.9)
[   17.362813] ACPI: Transitioning device [FN00] to D3
[   17.362819] ACPI: Transitioning device [FN00] to D3
[   17.362827] ACPI: Fan [FN00] (off)
[   17.379978] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   17.379990] ACPI: Processor [CPU1] (supports 8 throttling states)
[   17.380018] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[   17.392036] ACPI: Thermal Zone [THRM] (30 C)
[   18.880427] r8169 Gigabit Ethernet driver 2.2LK loaded
[   18.880471] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   18.880498] PCI: Setting latency timer of device 0000:02:00.0 to 64
[   18.881019] eth0: RTL8168b/8111b at 0xf8852000, 00:17:31:de:31:d7, XID 38000000 IRQ 220
[   19.044129] usbcore: registered new interface driver usbfs
[   19.044170] usbcore: registered new interface driver hub
[   19.071988] usbcore: registered new device driver usb
[   19.096608] USB Universal Host Controller Interface driver v3.0
[   19.096695] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
[   19.096714] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   19.096721] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   19.097055] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   19.097099] uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000ec00
[   19.097342] usb usb1: configuration #1 chosen from 1 choice
[   19.097390] hub 1-0:1.0: USB hub found
[   19.097401] hub 1-0:1.0: 2 ports detected
[   19.199870] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 17
[   19.199890] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   19.199898] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   19.199940] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   19.199983] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e880
[   19.200192] usb usb2: configuration #1 chosen from 1 choice
[   19.200238] hub 2-0:1.0: USB hub found
[   19.200248] hub 2-0:1.0: 2 ports detected
[   19.292157] SCSI subsystem initialized
[   19.309660] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20
[   19.309678] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   19.309686] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   19.309728] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   19.309769] uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000e800
[   19.309972] usb usb3: configuration #1 chosen from 1 choice
[   19.310018] hub 3-0:1.0: USB hub found
[   19.310028] hub 3-0:1.0: 2 ports detected
[   19.411512] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 21
[   19.411530] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[   19.411539] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   19.411584] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   19.411626] uhci_hcd 0000:00:1d.3: irq 21, io base 0x0000e480
[   19.411830] usb usb4: configuration #1 chosen from 1 choice
[   19.411876] hub 4-0:1.0: USB hub found
[   19.411886] hub 4-0:1.0: 2 ports detected
[   19.451267] libata version 3.00 loaded.
[   19.515511] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
[   19.515534] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   19.515541] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   19.515587] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[   19.519521] ehci_hcd 0000:00:1d.7: debug port 1
[   19.519531] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   19.519543] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebfbc00
[   19.535819] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   19.536016] usb usb5: configuration #1 chosen from 1 choice
[   19.536063] hub 5-0:1.0: USB hub found
[   19.536075] hub 5-0:1.0: 8 ports detected
[   19.639290] ACPI: PCI Interrupt 0000:04:01.1[b] -> GSI 18 (level, low) -> IRQ 20
[   19.692055] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20]  MMIO=[feaff800-feafffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[   19.877931] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 20
[   19.877991] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   19.878013] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
[   19.895971] ata_piix 0000:00:1f.1: version 2.12
[   19.895992] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 20
[   19.896040] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   19.902494] scsi0 : ata_piix
[   19.903570] scsi1 : ata_piix
[   19.906086] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[   19.906093] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[   20.286449] ata1.00: ATA-6: ST98823A, 3.06, max UDMA/100
[   20.286457] ata1.00: 156301488 sectors, multi 16: LBA48
[   20.286509] ata1.01: ATAPI: MATSHITADVD-RAM UJ-841S, 1.00, max UDMA/33
[   20.302363] ata1.00: configured for UDMA/100
[   20.474087] ata1.01: configured for UDMA/33
[   20.474154] ata2: port disabled. ignoring.
[   20.474368] scsi 0:0:0:0: Direct-Access     ATA      ST98823A         3.06 PQ: 0 ANSI: 5
[   20.476386] scsi 0:0:1:0: CD-ROM            MATSHITA DVD-RAM UJ-841S  1.00 PQ: 0 ANSI: 5
[   20.765827] Driver 'sd' needs updating - please use bus_type methods
[   20.765962] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[   20.765988] sd 0:0:0:0: [sda] Write Protect is off
[   20.765993] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   20.766027] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   20.766110] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[   20.766131] sd 0:0:0:0: [sda] Write Protect is off
[   20.766136] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   20.766169] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   20.766176]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[   20.778742]  sda1 sda2 sda3
[   20.796957] sd 0:0:0:0: [sda] Attached SCSI disk
[   20.811246] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   20.811283] sr 0:0:1:0: Attached scsi generic sg1 type 5
[   20.815901] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[   20.815909] Uniform CD-ROM driver Revision: 3.20
[   20.815988] sr 0:0:1:0: Attached scsi CD-ROM sr0
[   21.144560] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800035d6143]
[   21.302906] Attempting manual resume
[   21.302914] swsusp: Resume From Partition 8:3
[   21.302917] PM: Checking swsusp image.
[   21.303160] PM: Resume from disk failed.
[   21.363968] Clocksource tsc unstable (delta = -6286791096 ns)
[   21.370223] Time: hpet clocksource has been installed.
[   21.370340] kjournald starting.  Commit interval 5 seconds
[   21.370363] EXT3-fs: mounted filesystem with ordered data mode.
[   33.539944] iTCO_vendor_support: vendor-support=0
[   33.571872] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   33.572062] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x0860)
[   33.572141] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   33.627440] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   33.688205] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   33.739574] Linux agpgart interface v0.102
[   33.919387] input: PC Speaker as /devices/platform/pcspkr/input/input2
[   34.226328] intel_rng: FWH not detected
[   35.484707] input: Power Button (FF) as /devices/virtual/input/input3
[   35.496433] ACPI: Power Button (FF) [PWRF]
[   35.496626] input: Lid Switch as /devices/virtual/input/input4
[   35.497146] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   35.532724] ACPI: Lid Switch [LID]
[   35.532875] input: Power Button (CM) as /devices/virtual/input/input5
[   35.548320] ACPI: Power Button (CM) [PWRB]
[   35.548467] input: Sleep Button (CM) as /devices/virtual/input/input6
[   35.560305] ACPI: Sleep Button (CM) [SLPB]
[   35.703800] asus-laptop: Asus Laptop Support version 0.42
[   35.704278] asus-laptop:   A6JC model detected
[   35.783968] Registered led device: asus:mail
[   37.776453] nvidia: module license 'NVIDIA' taints kernel.
[   38.906441] Yenta: CardBus bridge found at 0000:04:01.0 [1043:1237]
[   38.966277] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.0
[   38.966286] iwl3945: Copyright(c) 2003-2007 Intel Corporation
[   39.034991] Yenta: ISA IRQ mask 0x0cb8, PCI irq 18
[   39.034997] Socket status: 30000006
[   39.035003] Yenta: Raising subordinate bus# of parent bus (#04) from #05 to #08
[   39.035011] pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
[   39.035017] cs: IO port probe 0xd000-0xdfff: clean.
[   39.035446] pcmcia: parent PCI bridge Memory window: 0xfe200000 - 0xfeafffff
[   39.035452] pcmcia: parent PCI bridge Memory window: 0xddf00000 - 0xdfefffff
[   39.170248] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 17
[   39.170270] PCI: Setting latency timer of device 0000:03:00.0 to 64
[   39.170303] iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
[   39.337486] ACPI: AC Adapter [AC0] (off-line)
[   39.393514] sdhci: Secure Digital Host Controller Interface driver
[   39.393520] sdhci: Copyright(c) Pierre Ossman
[   39.754087] ACPI: Battery Slot [BAT0] (battery present)
[   40.016854] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input7
[   40.032337] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   43.379989] Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[   43.416427] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[   45.258187] sdhci: SDHCI controller found at 0000:04:01.2 [1180:0822] (rev 17)
[   45.258226] ACPI: PCI Interrupt 0000:04:01.2[C] -> GSI 19 (level, low) -> IRQ 17
[   45.258251] sdhci:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
[   45.258321] mmc0: SDHCI at 0xfeaff400 irq 17 DMA
[   45.263509] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 22
[   45.263538] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   45.326630] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[   45.335091] wmaster0: Selected rate control algorithm 'iwl-3945-rs'
[   45.372808] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   45.372828] PCI: Setting latency timer of device 0000:01:00.0 to 64
[   45.373000] NVRM: loading NVIDIA UNIX x86 Kernel Module  169.12  Thu Feb 14 17:53:07 PST 2008
[   45.495502] cs: IO port probe 0x100-0x3af: clean.
[   45.497374] cs: IO port probe 0x3e0-0x4ff: clean.
[   45.497929] cs: IO port probe 0x820-0x8ff: clean.
[   45.498354] cs: IO port probe 0xc00-0xcf7: clean.
[   45.499323] cs: IO port probe 0xa00-0xaff: clean.
[   45.929182] udev: renamed network interface wlan0 to eth1
[   46.214116] lp: driver loaded but no devices found
[   46.666010] Adding 1630588k swap on /dev/sda3.  Priority:-1 extents:1 across:1630588k
[   46.717834] EXT3 FS on sda1, internal journal
[   47.923150] ip_tables: (C) 2000-2006 Netfilter Core Team
[   48.765907] No dock devices found.
[   50.933528] r8169: eth0: link down
[   51.175713] ppdev: user-space parallel port driver
[   51.518573] audit(1209470329.616:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5176 profile="/usr/sbin/cupsd" namespace="default"
[   51.555717] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   51.555721] apm: overridden by ACPI.
[   52.848504] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   52.848513] vboxdrv: Successfully done.
[   52.849998] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   52.850005] vboxdrv: Successfully loaded version 1.5.6 (interface 0x00050002).
[   52.993893] tun: Universal TUN/TAP device driver, 1.6
[   52.993902] tun: (C) 1999-2004 Max Krasnyansky
[   53.795568] Bluetooth: Core ver 2.11
[   53.797279] NET: Registered protocol family 31
[   53.797286] Bluetooth: HCI device and connection manager initialized
[   53.797293] Bluetooth: HCI socket layer initialized
[   53.952724] Bluetooth: L2CAP ver 2.9
[   53.952729] Bluetooth: L2CAP socket layer initialized
[   53.990402] Bluetooth: RFCOMM socket layer initialized
[   53.990415] Bluetooth: RFCOMM TTY layer initialized
[   53.990417] Bluetooth: RFCOMM ver 1.8
[   56.058076] NET: Registered protocol family 10
[   56.059176] lo: Disabled Privacy Extensions
[   56.060528] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   56.062093] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   63.008716] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   63.008730] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX_PWR_TABLE_CMD (0x97) seq 0x0425 ser 0x0000004B
[   64.001664] iwl3945: Can't stop Rx DMA.
[   69.702844] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   69.702864] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX_PWR_TABLE_CMD (0x97) seq 0x0407 ser 0x0000004B
[   70.696181] iwl3945: Can't stop Rx DMA.
[   85.435748] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   85.435772] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX_PWR_TABLE_CMD (0x97) seq 0x0413 ser 0x0000004B
[   86.429278] iwl3945: Can't stop Rx DMA.
[   87.435495] NET: Registered protocol family 17
[   87.953421] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   87.953442] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX (0x1C) seq 0x0000 ser 0x0000004B
[   88.946722] iwl3945: Can't stop Rx DMA.
[   90.793382] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   90.793406] iwl3945: Error Reply type 0x00000005 cmd REPLY_RATE_SCALE (0x47) seq 0x0406 ser 0x0000004B
[   91.786771] iwl3945: Can't stop Rx DMA.
[   95.283594] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   95.283615] iwl3945: Error Reply type 0x00000005 cmd REPLY_RATE_SCALE (0x47) seq 0x0406 ser 0x0000004B
[   96.276985] iwl3945: Can't stop Rx DMA.
[   97.842977] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   97.842994] iwl3945: Error Reply type 0x00000005 cmd REPLY_RATE_SCALE (0x47) seq 0x0406 ser 0x0000004B
[   98.835911] iwl3945: Can't stop Rx DMA.
[  103.839508] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[  103.839532] iwl3945: Error Reply type 0x00000005 cmd REPLY_RATE_SCALE (0x47) seq 0x0406 ser 0x0000004B
[  104.832892] iwl3945: Can't stop Rx DMA.
[  106.006999] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[  106.007010] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX_PWR_TABLE_CMD (0x97) seq 0x0407 ser 0x0000004B
[  106.999928] iwl3945: Can't stop Rx DMA.
[  114.040582] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[  114.040606] iwl3945: Error Reply type 0x00000005 cmd REPLY_RATE_SCALE (0x47) seq 0x0406 ser 0x0000004B
[  115.033991] iwl3945: Can't stop Rx DMA.
[  123.330412] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[  123.330435] iwl3945: Error Reply type 0x00000005 cmd REPLY_RATE_SCALE (0x47) seq 0x0406 ser 0x0000004B
[  124.323812] iwl3945: Can't stop Rx DMA.
[  125.790881] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[  125.790904] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX_PWR_TABLE_CMD (0x97) seq 0x0407 ser 0x0000004B
[  126.784276] iwl3945: Can't stop Rx DMA.
[  153.238545] usb 5-1: new high speed USB device using ehci_hcd and address 2
[  153.372979] usb 5-1: configuration #1 chosen from 1 choice
[  153.778851] usbcore: registered new interface driver libusual
[  153.816479] Initializing USB Mass Storage driver...
[  153.857315] scsi2 : SCSI emulation for USB Mass Storage devices
[  153.859230] usbcore: registered new interface driver usb-storage
[  153.860010] USB Mass Storage support registered.
[  153.860755] usb-storage: device found at 2
[  153.860761] usb-storage: waiting for device to settle before scanning
[  154.653614] usb-storage: device scan complete
[  154.655257] scsi 2:0:0:0: Direct-Access     JetFlash TS1GJF2A/120     8.07 PQ: 0 ANSI: 2
[  154.670146] sd 2:0:0:0: [sdb] 2007040 512-byte hardware sectors (1028 MB)
[  154.670774] sd 2:0:0:0: [sdb] Write Protect is off
[  154.670780] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
[  154.670786] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  154.673393] sd 2:0:0:0: [sdb] 2007040 512-byte hardware sectors (1028 MB)
[  154.674023] sd 2:0:0:0: [sdb] Write Protect is off
[  154.674029] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
[  154.674034] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  154.674041]  sdb: sdb1
[  154.674762] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[  154.674835] sd 2:0:0:0: Attached scsi generic sg2 type 0
[  201.459714] usb 2-1: new low speed USB device using uhci_hcd and address 2
[  201.690659] usb 2-1: configuration #1 chosen from 1 choice
[  202.517530] usbcore: registered new interface driver hiddev
[  202.531693] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.0/input/input9
[  202.553945] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.1-1
[  202.553981] usbcore: registered new interface driver usbhid
[  202.553989] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[  249.308936] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[  273.420862] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.0
[  273.420872] iwl3945: Copyright(c) 2003-2007 Intel Corporation
[  273.420995] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 17
[  273.421020] PCI: Setting latency timer of device 0000:03:00.0 to 64
[  273.421050] iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
[  273.565788] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[  273.569909] wmaster0: Selected rate control algorithm 'iwl-3945-rs'
[  273.615324] udev: renamed network interface wlan0 to eth1
[  273.668001] ADDRCONF(NETDEV_UP): eth1: link is not ready
[  277.653400] eth1: Initial auth_alg=0
[  277.653411] eth1: authenticate with AP 00:17:9a:7c:e1:2a
[  277.656378] eth1: RX authentication from 00:17:9a:7c:e1:2a (alg=0 transaction=2 status=0)
[  277.656387] eth1: authenticated
[  277.656392] eth1: associate with AP 00:17:9a:7c:e1:2a
[  277.659694] eth1: RX AssocResp from 00:17:9a:7c:e1:2a (capab=0x421 status=0 aid=53)
[  277.659702] eth1: associated
[  277.662707] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[  277.692508] eth1: Initial auth_alg=0
[  277.692520] eth1: authenticate with AP 00:17:9a:7c:e1:2a
[  277.693517] eth1: Initial auth_alg=0
[  277.693524] eth1: authenticate with AP 00:17:9a:7c:e1:2a
[  277.695395] eth1: RX authentication from 00:17:9a:7c:e1:2a (alg=0 transaction=2 status=0)
[  277.695403] eth1: authenticated
[  277.695408] eth1: associate with AP 00:17:9a:7c:e1:2a
[  277.698689] eth1: RX ReassocResp from 00:17:9a:7c:e1:2a (capab=0x421 status=0 aid=53)
[  277.698699] eth1: associated
[  283.963124] eth1: no IPv6 routers present
Human Knowledge Belongs To The World -- Antitrust (2001)
Nederlandstalige Ubuntu documentatie van Ubuntu-NL (wiki)

Yce

  • Gast
Heb problemen met intel wifi kaart
« Reactie #8 Gepost op: 2008/04/29, 16:11:08 »
Hallo,

Heb gisteren Ubuntu versie 6.0 geinstalleerd wat verder zonder problemen verliep.
Er van uitgaande dat hij automatisch ging updaten liep ik tegen het volgende probleem aan.
Toen ik nog onder Windows werkte deed internet het prima,maar nu ik Ubuntu heb,heb ik totaal geen internet.
Via een steunpunt in de buurt voor een oplossing gevraagt maar deze kon me helaas niet verder helpen.
Heb overigens niet voor een dualboot gekozen maar voor een volledige harde schijf Ubuntu en misschien wringt daar de schoen wel.
Werk met een insteekkaartje van Speedtouch in mijn laptop.
Aan de installatie cd hiervan heb ik ook niets want daar staan geen Linux drivers op.
Wat moet ik doen om weer internet te krijgen ?
We werken hier by the way met UPC Chello.

Help, Yce...

Offline profoX

  • Lid
    • wesley
    • Lionslink
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #9 Gepost op: 2008/04/29, 16:11:43 »
Citaat van: ggs1988
Ik heb ook een probleem met mijn wireless card. Ik heb het ondertussen op launchepad gezet en er blijken nog mensen te zijn die problemen hebben met dezelfde kaart. Ik heb een 3945ABG Network kaart van Intel.

Grtz GGS1988
Heb je toevallig een link naar die bug op Launchpad?
Kan je ook even melden wat voor computer of laptop je precies hebt?

Ik heb zelf (op een HP Pavilion dv9000-en-zoveel) geen enkel probleem met deze kaart.
Ik vermoed dat er hier specifieke driver (of ACPI/APIC) issues aanwezig zijn.

De syslog van philiper geeft aan:
Citaat
[   63.008716] iwl3945: Microcode SW error detected.  Restarting 0x82000008.
[   63.008730] iwl3945: Error Reply type 0x00000005 cmd REPLY_TX_PWR_TABLE_CMD (0x97) seq 0x0425 ser 0x0000004B
[   64.001664] iwl3945: Can't stop Rx DMA.
Herladen van de module (via rmmod / modprobe) lost het probleem (tijdelijk) op.
Human Knowledge Belongs To The World -- Antitrust (2001)
Nederlandstalige Ubuntu documentatie van Ubuntu-NL (wiki)

Offline G. Schrijvers

  • Lid
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #10 Gepost op: 2008/04/30, 08:29:22 »
Ik denk dat het niet uitmaakt wel merk van laptop je hebt, maar dat het probleem ligt bij de Intel Pro Wireless Network 3945ABG kaart.

Mijn laptop is een Packard Bell Easynote MX65 waarbij ik voor de rest geen enkel probleem mee heb.
Grtz GGS1988

Laptop: Packard Bell: Easynote MX 65 100    :   Debian Edge (32-bit) (Test-server)
Laptop: Dell XPS 1530                               :   Ubuntu 8.10 (64-bit)
Desktop: AMD 6000, HD3870, 4GB DDR2        :   Ubuntu 8.04 (64-bit)

Offline profoX

  • Lid
    • wesley
    • Lionslink
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #11 Gepost op: 2008/04/30, 12:40:03 »
ggs1988: het ligt niet enkel aan die kaart/driver, want ik heb geen enkel probleem ermee..
Citaat
Ik heb zelf (op een HP Pavilion dv9000-en-zoveel) geen enkel probleem met deze kaart.
waarschijnlijk wordt het nog veroorzaakt door iets anders.
philiper, probeer eens te booten met de boot parameters: noapic nolapic acpi=off pci=noacpi

in grub op de lijn met ubuntu gaan staan, druk op e, ga naar de lijn die met kernel begint, druk op e, voeg achteraan de lijn toe: noapic nolapic acpi=off noacpi pci=noacpi, druk op enter, druk op b om te booten

geeft dat nog steeds problemen met de draadloze netwerkverbinding?
Human Knowledge Belongs To The World -- Antitrust (2001)
Nederlandstalige Ubuntu documentatie van Ubuntu-NL (wiki)

Offline siegi

  • Lid
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #12 Gepost op: 2008/04/30, 18:45:56 »
Inderdaad profox een intel 3945 werkt hier ook prima out of the box in mijn dell D830 laptop.

philiper

  • Gast
Heb problemen met intel wifi kaart
« Reactie #13 Gepost op: 2008/05/02, 13:11:14 »
Citaat van: profoX
ggs1988: het ligt niet enkel aan die kaart/driver, want ik heb geen enkel probleem ermee..
Citaat
Ik heb zelf (op een HP Pavilion dv9000-en-zoveel) geen enkel probleem met deze kaart.
waarschijnlijk wordt het nog veroorzaakt door iets anders.
philiper, probeer eens te booten met de boot parameters: noapic nolapic acpi=off pci=noacpi

in grub op de lijn met ubuntu gaan staan, druk op e, ga naar de lijn die met kernel begint, druk op e, voeg achteraan de lijn toe: noapic nolapic acpi=off noacpi pci=noacpi, druk op enter, druk op b om te booten

geeft dat nog steeds problemen met de draadloze netwerkverbinding?
Jep lukt nog altijd niet

Offline G. Schrijvers

  • Lid
  • Steunpunt: Nee
Heb problemen met intel wifi kaart
« Reactie #14 Gepost op: 2008/05/03, 11:27:18 »
Bij mij zijn met deze parameters de problemen nog erger geworden :s Ik zie nu zelfs geen netwerken meer. Hiervoor kon ik ze zien en zag ik de signaal sterkte maar kon ik niet connecteren met de netwerken.
Grtz GGS1988

Laptop: Packard Bell: Easynote MX 65 100    :   Debian Edge (32-bit) (Test-server)
Laptop: Dell XPS 1530                               :   Ubuntu 8.10 (64-bit)
Desktop: AMD 6000, HD3870, 4GB DDR2        :   Ubuntu 8.04 (64-bit)