Hallo,
Al een tijdje zit ik te stoeien met het branden onder Hardy. Sommige CD's lukken, de meeste mislukken halverwege een keer. Ik heb een gloednieuwe Plextor brander dus daar ligt het niet aan. Ik dacht eerst dat Wodim de schuldige was, en heb dit pakket naar de nieuwere 1.1.9 versie geupgrade. (in hardy is wodim 1.1.6)
Ook dat mocht dus niet baten. Ook een oplossing van het laden van de 'piix'-module die ik op dit forum tegen kwam werkt niet.
Hierbij het foutrapport van k3b:
System
-----------------------
K3b Version: 1.0.4
KDE Version: 3.5.10
QT Version: 3.3.8b
Kernel: 2.6.24-24-generic
Devices
-----------------------
E-IDE CD-ROM 52X/AKH A62 (/dev/scd1, ) [CD-ROM] [Error] [None]
PLEXTOR DVDR PX-860A 1.00 (/dev/scd0, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump]
Used versions
-----------------------
cdrecord: 1.1.9
cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.9
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'PLEXTOR '
Identification : 'DVDR PX-860A '
Revision : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0002 (Removable disk)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1136640 = 1110 KB
FIFO size : 12582912 = 12288 KB
Speed set to 1764 KB/s
Track 01: data 570 MB
Total size: 655 MB (64:55.09) = 292132 sectors
Lout start: 655 MB (64:57/07) = 292132 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 3
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11745 (97:25/30)
ATIP start of lead out: 359848 (79:59/73)
1T speed low: 4 1T speed high: 10
2T speed low: 4 2T speed high: 0 (reserved val 6)
power mult factor: 1 5
recommended erase/write power: 5
A1 values: 24 1A D8
A2 values: 26 B2 4A
Disk type: Phase change
Manuf. index: 40
Manufacturer: INFODISC Technology Co., Ltd.
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 67716
Starting to write CD/DVD at speed 10.0 in real SAO mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 570 MB written.
Track 01: 1 of 570 MB written (fifo 100%) [buf 99%] 0.4x.
Track 01: 2 of 570 MB written (fifo 100%) [buf 99%] 10.3x.
Track 01: 3 of 570 MB written (fifo 100%) [buf 99%] 10.6x.
~~ en zo een hele lijst tot: ~~
Track 01: 533 of 570 MB written (fifo 100%) [buf 99%] 10.2x.
Track 01: 534 of 570 MB written (fifo 100%) [buf 99%] 10.5x.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 04 2D 9F 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 04 00 00 00 00 00 0E 09 0C 00 00 00 00 00 00
Sense Key: 0x0 No Additional Sense, Segment 4
Sense Code: 0x00 Qual 0x00 (no additional sense information) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.844s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 560789504 bytes
Writing time: 395.407s
Average write speed 10.1x.
Min drive buffer fill was 98%
Fixating...
Fixating time: 10.696s
/usr/bin/wodim: fifo had 9025 puts and 8834 gets.
/usr/bin/wodim: fifo was 0 times empty and 7835 times full, min fill was 78%.
cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/scd0 speed=10 -dao driveropts=burnfree -eject -data -tsize=292132s -
Ik hoop dat iemand een eenduidig antwoord heeft.
vr. groet, Erwin
