Misschien kan iemand hier de fout met mijn hardware uit halen?
erwin@Ubuntu:~$ dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Thu Jun 7 20:19:32 UTC 2007 (Ubuntu 2.6.20-16.29-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fe40000 end: 000000003ff40000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000003ff40000 size: 0000000000010000 end: 000000003ff50000 type: 3
[ 0.000000] copy_e820_map() start: 000000003ff50000 size: 00000000000b0000 end: 0000000040000000 type: 4
[ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ff380000 size: 0000000000c80000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ff40000 (usable)
[ 0.000000] BIOS-e820: 000000003ff40000 - 000000003ff50000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ff50000 - 0000000040000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 261952) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261952
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261952
[ 0.000000] On node 0 totalpages: 261952
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 254 pages used for memmap
[ 0.000000] HighMem zone: 32322 pages, LIFO batch:7
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 ACPIAM ) @ 0x000fa550
[ 0.000000] ACPI: RSDT (v001 A M I OEMRSDT 0x08000615 MSFT 0x00000097) @ 0x3ff40000
[ 0.000000] ACPI: FADT (v002 A M I OEMFACP 0x08000615 MSFT 0x00000097) @ 0x3ff40200
[ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x08000615 MSFT 0x00000097) @ 0x3ff40300
[ 0.000000] ACPI: OEMB (v001 A M I OEMBIOS 0x08000615 MSFT 0x00000097) @ 0x3ff50040
[ 0.000000] ACPI: DSDT (v001 P4i6G P4i6G113 0x00000113 INTL 0x02002026) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bee00000)
[ 0.000000] Detected 2599.839 MHz processor.
[ 21.691987] Built 1 zonelists. Total pages: 259906
[ 21.691992] Kernel command line: root=UUID=18cbf5d9-a1b1-48bf-a397-b6a0206bd62a ro quiet splash locale=nl_NL
[ 21.692161] mapped APIC to ffffd000 (fee00000)
[ 21.692164] mapped IOAPIC to ffffc000 (fec00000)
[ 21.692167] Enabling fast FPU save and restore... done.
[ 21.692170] Enabling unmasked SIMD FPU exception support... done.
[ 21.692181] Initializing CPU#0
[ 21.692255] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 21.696494] Console: colour VGA+ 80x25
[ 21.696987] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 21.697465] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 21.722520] Memory: 1027608k/1047808k available (1992k kernel code, 19512k reserved, 900k data, 328k init, 130304k highmem)
[ 21.722531] virtual kernel memory layout:
[ 21.722532] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 21.722534] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 21.722535] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 21.722536] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 21.722537] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 21.722538] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB)
[ 21.722539] .text : 0xc0100000 - 0xc02f2374 (1992 kB)
[ 21.722542] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 21.800022] Calibrating delay using timer specific routine.. 5203.55 BogoMIPS (lpj=10407116)
[ 21.800071] Security Framework v1.0.0 initialized
[ 21.800080] SELinux: Disabled at boot.
[ 21.800098] Mount-cache hash table entries: 512
[ 21.800274] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[ 21.800287] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 21.800290] CPU: L2 cache: 512K
[ 21.800293] CPU: Physical Processor ID: 0
[ 21.800295] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 00000000 00000000
[ 21.800308] Compat vDSO mapped to ffffe000.
[ 21.800313] Remapping vsyscall page to ffffe000
[ 21.800326] Checking 'hlt' instruction... OK.
[ 21.816097] SMP alternatives: switching to UP code
[ 21.816516] Early unpacking initramfs... done
[ 22.115971] ACPI: Core revision 20060707
[ 22.116145] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 22.118091] CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
[ 22.118115] SMP alternatives: switching to SMP code
[ 22.118261] Booting processor 1/1 eip 3000
[ 22.128528] Initializing CPU#1
[ 22.207121] Calibrating delay using timer specific routine.. 5199.82 BogoMIPS (lpj=10399645)
[ 22.207131] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[ 22.207142] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 22.207145] CPU: L2 cache: 512K
[ 22.207147] CPU: Physical Processor ID: 0
[ 22.207150] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 00000000 00000000
[ 22.207315] CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
[ 22.207358] Total of 2 processors activated (10403.38 BogoMIPS).
[ 22.207489] ENABLING IO-APIC IRQs
[ 22.207674] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 22.354806] checking TSC synchronization across 2 CPUs: passed.
[ 0.003994] Brought up 2 CPUs
[ 0.064739] migration_cost=128
[ 0.065072] Booting paravirtualized kernel on bare hardware
[ 0.065162] Time: 10:42:41 Date: 06/21/107
[ 0.065198] NET: Registered protocol family 16
[ 0.065314] EISA bus registered
[ 0.065320] ACPI: bus type pci registered
[ 0.065395] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
[ 0.065397] PCI: Using configuration type 1
[ 0.065399] Setting up standard PCI resources
[ 0.081019] ACPI: Interpreter enabled
[ 0.081024] ACPI: Using IOAPIC for interrupt routing
[ 0.081625] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.081631] PCI: Probing PCI hardware (bus 00)
[ 0.082284] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[ 0.082288] PCI quirk: region 0480-04bf claimed by ICH4 GPIO
[ 0.082542] Boot video device is 0000:01:00.0
[ 0.082710] PCI: Transparent bridge - 0000:00:1e.0
[ 0.082738] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.084769] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.090976] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.091233] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[ 0.091492] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.091748] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.092012] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.092268] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.092527] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.092783] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.092949] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.092968] pnp: PnP ACPI init
[ 0.097724] pnp: PnP ACPI: found 12 devices
[ 0.097730] PnPBIOS: Disabled by ACPI PNP
[ 0.097805] PCI: Using ACPI for IRQ routing
[ 0.097810] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.101219] NET: Registered protocol family 8
[ 0.101221] NET: Registered protocol family 20
[ 0.101957] pnp: 00:0a: ioport range 0x680-0x6ff has been reserved
[ 0.101961] pnp: 00:0a: ioport range 0x295-0x296 has been reserved
[ 0.102410] PCI: Bridge: 0000:00:01.0
[ 0.102412] IO window: disabled.
[ 0.102417] MEM window: f3d00000-f7dfffff
[ 0.102422] PREFETCH window: d3c00000-f3bfffff
[ 0.102428] PCI: Bridge: 0000:00:1e.0
[ 0.102432] IO window: b000-bfff
[ 0.102437] MEM window: f7e00000-f7efffff
[ 0.102442] PREFETCH window: disabled.
[ 0.102460] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.102501] NET: Registered protocol family 2
[ 0.147753] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.147932] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.148547] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.149127] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.149131] TCP reno registered
[ 0.159824] checking if image is initramfs... it is
[ 0.744825] Freeing initrd memory: 6789k freed
[ 0.745328] audit: initializing netlink socket (disabled)
[ 0.745342] audit(1185014561.488:1): initialized
[ 0.745492] highmem bounce pool size: 64 pages
[ 0.745615] VFS: Disk quotas dquot_6.5.1
[ 0.745639] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.745700] io scheduler noop registered
[ 0.745703] io scheduler anticipatory registered
[ 0.745706] io scheduler deadline registered
[ 0.745718] io scheduler cfq registered (default)
[ 0.746047] isapnp: Scanning for PnP cards...
[ 1.099176] isapnp: No Plug & Play device found
[ 1.133864] Real Time Clock Driver v1.12ac
[ 1.133933] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.134055] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.134947] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.135232] mice: PS/2 mouse device common for all mice
[ 1.136026] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.136210] input: Macintosh mouse button emulation as /class/input/input0
[ 1.136258] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1.136262] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1.136528] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.136531] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 1.138995] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.139001] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.139158] EISA: Probing bus 0 at eisa.0
[ 1.139199] EISA: Detected 0 cards.
[ 1.158337] input: AT Translated Set 2 keyboard as /class/input/input1
[ 1.169243] TCP cubic registered
[ 1.169253] NET: Registered protocol family 1
[ 1.169285] Starting balanced_irq
[ 1.169295] Using IPI No-Shortcut mode
[ 1.169403] Time: tsc clocksource has been installed.
[ 1.169431] ACPI: (supports S0 S1 S3 S4 S5)
[ 1.169483] Magic number: 15:327:730
[ 1.169946] Freeing unused kernel memory: 328k freed
[ 2.431490] Capability LSM initialized
[ 2.481724] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.481822] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
[ 2.481830] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
[ 3.072063] usbcore: registered new interface driver usbfs
[ 3.072102] usbcore: registered new interface driver hub
[ 3.072143] usbcore: registered new device driver usb
[ 3.073523] USB Universal Host Controller Interface driver v3.0
[ 3.073593] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 3.073609] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 3.073615] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.073748] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 3.073781] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e000
[ 3.073951] usb usb1: configuration #1 chosen from 1 choice
[ 3.073995] hub 1-0:1.0: USB hub found
[ 3.074005] hub 1-0:1.0: 2 ports detected
[ 3.134974] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 3.148253] SCSI subsystem initialized
[ 3.156461] libata version 2.20 loaded.
[ 3.177260] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 17
[ 3.177277] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 3.177284] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.177325] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 3.177356] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e400
[ 3.177493] usb usb2: configuration #1 chosen from 1 choice
[ 3.177538] hub 2-0:1.0: USB hub found
[ 3.177549] hub 2-0:1.0: 2 ports detected
[ 3.281083] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 3.281102] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.281108] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.281159] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 3.281191] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
[ 3.281357] usb usb3: configuration #1 chosen from 1 choice
[ 3.281418] hub 3-0:1.0: USB hub found
[ 3.281431] hub 3-0:1.0: 2 ports detected
[ 3.384734] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
[ 3.384751] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 3.384757] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.384796] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 3.384826] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ec00
[ 3.384992] usb usb4: configuration #1 chosen from 1 choice
[ 3.385056] hub 4-0:1.0: USB hub found
[ 3.385070] hub 4-0:1.0: 2 ports detected
[ 3.488669] ata_piix 0000:00:1f.1: version 2.10ac1
[ 3.488698] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 3.488725] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 3.488832] ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14
[ 3.489794] ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15
[ 3.489830] scsi0 : ata_piix
[ 3.520305] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 3.652283] ata1.00: ata_hpa_resize 1: sectors = 117304992, hpa_sectors = 117304992
[ 3.652288] ata1.00: ATA-6: SAMSUNG SP6003H, QV100-61, max UDMA/100
[ 3.652292] ata1.00: 117304992 sectors, multi 16: LBA
[ 3.660257] ata1.00: ata_hpa_resize 1: sectors = 117304992, hpa_sectors = 117304992
[ 3.660261] ata1.00: configured for UDMA/100
[ 3.660274] scsi1 : ata_piix
[ 3.685285] usb 2-1: configuration #1 chosen from 1 choice
[ 3.927393] usb 2-2: new full speed USB device using uhci_hcd and address 3
[ 4.080328] usb 2-2: configuration #1 chosen from 1 choice
[ 4.143176] ata2.00: ATAPI, max UDMA/100
[ 4.143181] ata2.01: ATAPI, max UDMA/33
[ 4.306794] ata2.00: configured for UDMA/100
[ 4.322520] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 4.473014] ata2.01: configured for UDMA/33
[ 4.473178] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP6003H QV10 PQ: 0 ANSI: 5
[ 4.473747] scsi 1:0:0:0: CD-ROM DVD-ROM 16X 5.AV PQ: 0 ANSI: 5
[ 4.476891] scsi 1:0:1:0: CD-ROM PHILIPS DVDRW416 P1.2 PQ: 0 ANSI: 5
[ 4.477311] 8139cp 0000:02:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 4.477317] 8139cp 0000:02:05.0: Try the "8139too" driver instead.
[ 4.479276] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
[ 4.479301] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4.479311] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.479374] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 4.479416] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.479424] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[ 4.479439] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xf7fffc00
[ 4.483306] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.483393] 8139too Fast Ethernet driver 0.9.28
[ 4.483521] usb usb5: configuration #1 chosen from 1 choice
[ 4.483569] hub 5-0:1.0: USB hub found
[ 4.483581] hub 5-0:1.0: 8 ports detected
[ 4.506380] usb 3-1: configuration #1 chosen from 1 choice
[ 4.510251] usb 3-1: can't set config #1, error -71
[ 4.586397] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 20
[ 4.586731] eth0: RealTek RTL8139 at 0xf8854c00, 00:13:8f:ce:9c:5e, IRQ 20
[ 4.586738] eth0: Identified 8139 chip type 'RTL-8101'
[ 4.616708] SCSI device sda: 117304992 512-byte hdwr sectors (60060 MB)
[ 4.618544] sda: Write Protect is off
[ 4.618551] sda: Mode Sense: 00 3a 00 00
[ 4.618621] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.618735] SCSI device sda: 117304992 512-byte hdwr sectors (60060 MB)
[ 4.618756] sda: Write Protect is off
[ 4.618761] sda: Mode Sense: 00 3a 00 00
[ 4.618799] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.618805] sda: sda1 sda2 <<6>usb 2-1: USB disconnect, address 2
[ 4.651993] sda5 >
[ 4.652131] sd 0:0:0:0: Attached scsi disk sda
[ 4.656898] sr0: scsi3-mmc drive: 0x/50x cd/rw xa/form2 cdda tray
[ 4.656905] Uniform CD-ROM driver Revision: 3.20
[ 4.656984] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.658074] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.658108] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.658138] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 4.665817] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 4.665913] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 4.765573] usb 2-2: USB disconnect, address 3
[ 4.960699] Attempting manual resume
[ 4.960703] swsusp: Resume From Partition 8:5
[ 4.960705] PM: Checking swsusp image.
[ 4.985369] PM: Resume from disk failed.
[ 5.029236] kjournald starting. Commit interval 5 seconds
[ 5.029247] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.499948] usb 5-5: new high speed USB device using ehci_hcd and address 4
[ 5.634134] usb 5-5: configuration #1 chosen from 1 choice
[ 5.815287] usb 3-1: USB disconnect, address 2
[ 6.182450] usb 3-2: new low speed USB device using uhci_hcd and address 3
[ 6.365819] usb 3-2: configuration #1 chosen from 1 choice
[ 6.605518] usb 2-1: new full speed USB device using uhci_hcd and address 4
[ 6.778726] usb 2-1: configuration #1 chosen from 1 choice
[ 7.020606] usb 2-2: new full speed USB device using uhci_hcd and address 5
[ 7.173766] usb 2-2: configuration #1 chosen from 1 choice
[ 17.850438] Linux agpgart interface v0.102 (c) Dave Jones
[ 18.074194] agpgart: Detected an Intel 865 Chipset.
[ 18.077097] agpgart: AGP aperture is 64M @ 0xf8000000
[ 18.202047] input: PC Speaker as /class/input/input2
[ 18.220139] parport: PnPBIOS parport detected.
[ 18.220240] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 18.715883] intel_rng: FWH not detected
[ 18.774390] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 18.776926] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 18.968211] Bluetooth: Core ver 2.11
[ 18.996987] NET: Registered protocol family 31
[ 18.996994] Bluetooth: HCI device and connection manager initialized
[ 18.997000] Bluetooth: HCI socket layer initialized
[ 19.012611] iTCO_vendor_support: vendor-support=0
[ 19.014379] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[ 19.014482] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
[ 19.014540] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 19.061360] ubuntu/wireless/at76/at76c503.c: Atmel at76c50x USB Wireless LAN Driver 0.14beta1 loading
[ 19.197904] ubuntu/wireless/at76/at76c503.c: firmware version 1.101.0 #86 (fcs_len 4)
[ 19.198894] ubuntu/wireless/at76/at76c503.c: device's MAC 00:0f:66:10:81:e5, regulatory domain ETSI (Europe - (Spain+France) (id 48)
[ 19.198977] ubuntu/wireless/at76/at76c503.c: registered wlan0
[ 19.199000] usbcore: registered new interface driver at76_usb
[ 19.218459] Bluetooth: HCI USB driver ver 2.9
[ 19.249526] nvidia: module license 'NVIDIA' taints kernel.
[ 19.252916] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 19.253228] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-7184 Tue Aug 1 18:38:58 PDT 2006
[ 19.270025] usbcore: registered new interface driver hci_usb
[ 19.381847] usbcore: registered new interface driver libusual
[ 19.381853] usbcore: registered new interface driver hiddev
[ 19.414218] Initializing USB Mass Storage driver...
[ 19.414347] scsi2 : SCSI emulation for USB Mass Storage devices
[ 19.414435] usb-storage: device found at 4
[ 19.414438] usb-storage: waiting for device to settle before scanning
[ 19.521508] input: Microsoft Microsoft Wireless Optical Mouse� 1.0A as /class/input/input3
[ 19.521665] input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse� 1.0A] on usb-0000:00:1d.2-2
[ 19.521711] usbcore: registered new interface driver usb-storage
[ 19.521718] USB Mass Storage support registered.
[ 19.521932] usbcore: registered new interface driver usbhid
[ 19.521938] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 19.710330] ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 17 (level, low) -> IRQ 21
[ 19.710372] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 20.024082] intel8x0_measure_ac97_clock: measured 55815 usecs
[ 20.024087] intel8x0: clocking to 48000
[ 20.300199] fuse init (API version 7.8)
[ 20.331519] lp0: using parport0 (interrupt-driven).
[ 20.373442] Adding 2433808k swap on /dev/disk/by-uuid/4f1a04d7-d3d2-45ec-bee6-9e4e90a8ec77. Priority:-1 extents:1 across:2433808k
[ 20.515895] EXT3 FS on sda1, internal journal
[ 22.031646] NET: Registered protocol family 17
[ 24.402690] usb-storage: device scan complete
[ 24.403306] scsi 2:0:0:0: Direct-Access takeMS USB Mini v1.0 PQ: 0 ANSI: 0 CCS
[ 24.404668] SCSI device sdb: 4029440 512-byte hdwr sectors (2063 MB)
[ 24.405277] sdb: Write Protect is off
[ 24.405281] sdb: Mode Sense: 23 00 00 00
[ 24.405283] sdb: assuming drive cache: write through
[ 24.407395] SCSI device sdb: 4029440 512-byte hdwr sectors (2063 MB)
[ 24.408018] sdb: Write Protect is off
[ 24.408021] sdb: Mode Sense: 23 00 00 00
[ 24.408023] sdb: assuming drive cache: write through
[ 24.408026] sdb: sdb1
[ 24.408731] sd 2:0:0:0: Attached scsi removable disk sdb
[ 24.408799] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 26.469946] ubuntu/wireless/at76/at76c503.c: 2522: assertion dev->istate == INIT failed
[ 28.184015] ubuntu/wireless/at76/at76c503.c: 1784: assertion dev->curr_bss == NULL failed
[ 30.681790] NET: Registered protocol family 10
[ 30.681945] lo: Disabled Privacy Extensions
[ 32.300446] input: Power Button (FF) as /class/input/input4
[ 32.300485] ACPI: Power Button (FF) [PWRF]
[ 32.300579] input: Power Button (CM) as /class/input/input5
[ 32.300624] ACPI: Power Button (CM) [PWRB]
[ 32.432600] ibm_acpi: ec object not found
[ 32.518052] No dock devices found.
[ 32.617801] Using specific hotkey driver
[ 32.691978] pcc_acpi: loading...
[ 36.595208] eth0: link down
[ 36.595250] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 39.422048] ppdev: user-space parallel port driver
[ 40.374389] apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
[ 40.374397] apm: disabled - APM is not SMP safe.
[ 40.733533] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 40.898304] wlan0: no IPv6 routers present
[ 40.917564] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 40.917862] NFSD: starting 90-second grace period
[ 41.999621] /dev/vmmon[5424]: Module vmmon: registered with major=10 minor=165
[ 42.000216] /dev/vmmon[5424]: Module vmmon: initialized
[ 42.121964] /dev/vmnet: open called by PID 5453 (vmnet-bridge)
[ 42.121986] /dev/vmnet: hub 0 does not exist, allocating memory.
[ 42.122045] /dev/vmnet: port on hub 0 successfully opened
[ 42.122239] bridge-eth0: enabling the bridge
[ 42.122258] bridge-eth0: up
[ 42.122274] bridge-eth0: already up
[ 42.122290] bridge-eth0: attached
[ 42.206484] /dev/vmnet: open called by PID 5467 (vmnet-natd)
[ 42.206504] /dev/vmnet: hub 8 does not exist, allocating memory.
[ 42.206567] /dev/vmnet: port on hub 8 successfully opened
[ 43.727356] Bluetooth: L2CAP ver 2.8
[ 43.727372] Bluetooth: L2CAP socket layer initialized
[ 43.780396] Bluetooth: RFCOMM socket layer initialized
[ 43.780417] Bluetooth: RFCOMM TTY layer initialized
[ 43.780422] Bluetooth: RFCOMM ver 1.8
[ 52.121366] /dev/vmnet: open called by PID 5800 (vmnet-netifup)
[ 52.121386] /dev/vmnet: hub 1 does not exist, allocating memory.
[ 52.121444] /dev/vmnet: port on hub 1 successfully opened
[ 52.140076] /dev/vmnet: open called by PID 5808 (vmnet-netifup)
[ 52.140101] /dev/vmnet: port on hub 8 successfully opened
[ 52.213574] /dev/vmnet: open called by PID 5822 (vmnet-dhcpd)
[ 52.213781] /dev/vmnet: port on hub 1 successfully opened
[ 52.214784] /dev/vmnet: open called by PID 5823 (vmnet-dhcpd)
[ 52.215032] /dev/vmnet: port on hub 8 successfully opened
[ 62.299363] vmnet8: no IPv6 routers present
[ 62.307344] vmnet1: no IPv6 routers present
[ 133.477770] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 133.584594] ISO 9660 Extensions: IEEE_P1282
[ 193.527461] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007
[ 392.398407] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007
[ 456.697861] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007
[ 457.073485] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 457.073512] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 457.073555] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 487.530800] usb 5-5: USB disconnect, address 4
[ 504.601335] usb 5-5: new high speed USB device using ehci_hcd and address 6
[ 504.735186] usb 5-5: configuration #1 chosen from 1 choice
[ 504.735593] scsi3 : SCSI emulation for USB Mass Storage devices
[ 504.735915] usb-storage: device found at 6
[ 504.735919] usb-storage: waiting for device to settle before scanning
[ 509.722343] usb-storage: device scan complete
[ 509.757603] scsi 3:0:0:0: Direct-Access Maxtor 6 Y080L0 YAR4 PQ: 0 ANSI: 0
[ 509.759451] SCSI device sdb: 156249999 512-byte hdwr sectors (80000 MB)
[ 509.760438] sdb: Write Protect is off
[ 509.760444] sdb: Mode Sense: 03 00 00 00
[ 509.760448] sdb: assuming drive cache: write through
[ 509.761557] SCSI device sdb: 156249999 512-byte hdwr sectors (80000 MB)
[ 509.762433] sdb: Write Protect is off
[ 509.762439] sdb: Mode Sense: 03 00 00 00
[ 509.762442] sdb: assuming drive cache: write through
[ 509.762447] sdb: sdb1
[ 509.774660] sd 3:0:0:0: Attached scsi disk sdb
[ 509.774735] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 547.163016] scsi: unknown opcode 0x01
[ 1123.918888] /dev/vmnet: open called by PID 8905 (vmware-vmx)
[ 1123.918929] /dev/vmnet: port on hub 8 successfully opened
[ 1124.097130] /dev/vmmon[8916]: host clock rate change request 0 -> 19
[ 1176.671035] /dev/vmmon[8916]: host clock rate change request 19 -> 0
[ 1176.671943] /dev/vmmon[8916]: host clock rate change request 0 -> 19
[ 1180.609150] /dev/vmmon[8905]: host clock rate change request 19 -> 0
[ 1180.611000] vmmon: Had to deallocate locked 2477 pages from vm driver ce851000
[ 1180.613777] vmmon: Had to deallocate AWE 2797 pages from vm driver ce851000
[ 1181.363684] /dev/vmnet: open called by PID 8905 (vmware-vmx)
[ 1181.363706] /dev/vmnet: port on hub 8 successfully opened
[ 1181.548209] /dev/vmmon[9025]: host clock rate change request 0 -> 19
[ 1190.989715] /dev/vmmon[8905]: host clock rate change request 19 -> 0
[ 1190.991734] vmmon: Had to deallocate locked 2345 pages from vm driver ce851000
[ 1190.994069] vmmon: Had to deallocate AWE 2503 pages from vm driver ce851000
[ 1247.087455] /dev/vmnet: open called by PID 9094 (vmware-vmx)
[ 1247.087483] /dev/vmnet: port on hub 8 successfully opened
[ 1247.341230] /dev/vmmon[9104]: host clock rate change request 0 -> 19
[ 1256.779242] /dev/vmmon[9094]: host clock rate change request 19 -> 0
[ 1256.780702] vmmon: Had to deallocate locked 1879 pages from vm driver c8cbb000
[ 1256.782975] vmmon: Had to deallocate AWE 2502 pages from vm driver c8cbb000
[ 1266.136199] /dev/vmnet: open called by PID 9151 (vmware-vmx)
[ 1266.136224] /dev/vmnet: port on hub 8 successfully opened
[ 1266.279750] /dev/vmmon[9161]: host clock rate change request 0 -> 19
[ 1458.316807] sr 1:0:0:0: SCSI error: return code = 0x08000002
[ 1458.316816] sr0: Current: sense key: Hardware Error
[ 1458.316821] Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
[ 1458.316831] end_request: I/O error, dev sr0, sector 88
[ 1458.316837] Buffer I/O error on device sr0, logical block 22
[ 1458.316854] Buffer I/O error on device sr0, logical block 23
[ 1458.316866] Buffer I/O error on device sr0, logical block 24
[ 1458.316873] Buffer I/O error on device sr0, logical block 25
[ 1458.316883] Buffer I/O error on device sr0, logical block 26
[ 1458.316893] Buffer I/O error on device sr0, logical block 27
[ 1458.316901] Buffer I/O error on device sr0, logical block 28
[ 1458.316909] Buffer I/O error on device sr0, logical block 29
[ 1458.316918] Buffer I/O error on device sr0, logical block 30
[ 1458.316926] Buffer I/O error on device sr0, logical block 31
[ 1458.363576] sr 1:0:0:0: SCSI error: return code = 0x08000002
[ 1458.363587] sr0: Current: sense key: Hardware Error
[ 1458.363591] Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
[ 1458.363601] end_request: I/O error, dev sr0, sector 140
[ 1458.511720] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 1458.699341] ISOFS: changing to secondary root
[ 1459.475679] sr 1:0:0:0: SCSI error: return code = 0x08000002
[ 1459.475733] sr0: Current: sense key: Hardware Error
[ 1459.475738] Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
[ 1459.475748] end_request: I/O error, dev sr0, sector 40500
[ 1459.515204] sr 1:0:0:0: SCSI error: return code = 0x08000002
[ 1459.515213] sr0: Current: sense key: Hardware Error
[ 1459.515218] Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
[ 1459.515227] end_request: I/O error, dev sr0, sector 40632
[ 1460.946840] sr 1:0:0:0: SCSI error: return code = 0x08000002
[ 1460.946851] sr0: Current: sense key: Hardware Error
[ 1460.946857] Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
[ 1460.946868] end_request: I/O error, dev sr0, sector 124
[ 1460.976703] sr 1:0:0:0: SCSI error: return code = 0x08000002
[ 1460.976714] sr0: Current: sense key: Hardware Error
[ 1460.976721] Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
[ 1460.976732] end_request: I/O error, dev sr0, sector 124
[ 1468.875788] /dev/vmmon[9161]: host clock rate change request 19 -> 0
[ 1468.876294] /dev/vmmon[9161]: host clock rate change request 0 -> 19
[ 1469.038842] /dev/vmmon[9161]: host clock rate change request 19 -> 63
[ 1469.553125] /dev/vmmon[9161]: host clock rate change request 63 -> 200
[ 1470.483523] /dev/vmmon[9161]: host clock rate change request 200 -> 201
[ 1512.471541] /dev/vmmon[9161]: host clock rate change request 201 -> 1001
[ 1531.252850] /dev/vmmon[9161]: host clock rate change request 1001 -> 201
[ 1973.651839] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 1973.843415] ISOFS: changing to secondary root
