Nieuws:

Welkom, Gast. Alsjeblieft inloggen of registreren.
Heb je de activerings-mail niet ontvangen?

Auteur Topic: Opgelost: Dash-home en software centrum te zwaar voor mijn computer?  (gelezen 2157 keer)

Als ik dash-home of het software centrum open dan trekt mijn computer het maar net. En soms helemaal niet dan loopt hij vast. In ieder geval gaat het erg langzaam/traag.

Vind ik erg vervelend  :| Is hier wat aan te doen? Zo ja... wat?

Alvast bedankt! Groeten Tomatito.
« Laatst bewerkt op: 2013/06/30, 08:32:54 door tomatito »
Ubuntu 18.04

Intel Skylake i3 6100, 8 GB DDR4, nVidia Geforce GTX 750 ti (2GB)

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #1 Gepost op: 2013/06/18, 08:13:55 »
De eerste vraag is:
Wat zijn de specs van de computer?

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #2 Gepost op: 2013/06/19, 02:47:40 »
Mag ik eerst nog een vraag stellen? Zijn dit zulke zware toepassingen?

Ik gebruik geregeld Gimp en Inkscape met grote/zware bestanden en dit gaat altijd probleemloos  :D
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Pentium(R) D CPU 2.80GHz
stepping : 7
microcode : 0x3
cpu MHz : 2790.921
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc pebs bts nopl pni dtes64 monitor ds_cpl cid cx16 xtpr lahf_lm
bogomips : 5581.84
clflush size : 64
cache_alignment : 128
address sizes : 36 bits physical, 48 bits virtual
power management:

processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Intel(R) Pentium(R) D CPU 2.80GHz
stepping : 7
microcode : 0x3
cpu MHz : 2790.921
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
apicid : 1
initial apicid : 1
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc pebs bts nopl pni dtes64 monitor ds_cpl cid cx16 xtpr lahf_lm
bogomips : 5582.05
clflush size : 64
cache_alignment : 128
address sizes : 36 bits physical, 48 bits virtual
power management:

Het is 2e hands Dell (kantoor) computer  ;) Echt onverwoestbaar.

Ubuntu 18.04

Intel Skylake i3 6100, 8 GB DDR4, nVidia Geforce GTX 750 ti (2GB)

Offline aartje

  • Lid
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #3 Gepost op: 2013/06/19, 08:05:17 »
het enige wat ik hier uit kan halen is dat het een Dell is met
een pentium D processor van 2,8 GHz.

Maar niets over geheugen, diskindeling, graphics etc.etc
sudo lshw -html > xx.html
geeft alle gegevens.

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #4 Gepost op: 2013/06/19, 08:27:04 »
De Unity interface is inderdaad een stuk zwaarder dan de gnome2 voorganger.
Bij 13.04 schijnt er een stuk optimalisatie te zijn uitgevoerd. Ik draai zelf 12.04 dus kan het niet controleren.

Aangezien je een Pentium D hebt denk ik dat het ram geheugen niet boven de 1 GB uit komt.
Klopt dit?

Je kan de Ubuntu 2D instelling proberen. Deze heeft minder zware grafische rompslomp.
Dit doe je door:
1. Uit te loggen
2. bij het logo rechtsboven de gebruikersnaam kiezen voor 'Ubuntu 2D'.
3. Weer inloggen.

Een andere optie is Xubuntu.
Xubuntu heeft de xfce interface die een stuk luchter is.

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #5 Gepost op: 2013/06/19, 08:53:41 »
Dit gaat niet werken Erik, want 13.04 heeft standaard Unity 2D niet geïnstalleerd.

Kijk ook eens in dit topic. Ik zit met hetzelfde probleem  ;) .

Groeten,
Mischa

Offline markba

  • Lid
    • http://markbaaijens.nl/
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #6 Gepost op: 2013/06/19, 09:21:49 »
De Unity interface is inderdaad een stuk zwaarder dan de gnome2 voorganger.
Bij 13.04 schijnt er een stuk optimalisatie te zijn uitgevoerd.
Ja en nee. Ten eerste zijn de 2D en 3D omgevingen binnen 13.04 samengevoegd. Dat wil dus zeggen dat je in 13.04 eigenlijk altijd een 3D omgeving krijgt, maar daar waar grafische kunstjes vertoond moeten worden (o.a. Dash), en de grafische kaart kan dat niet aan, dan wordt er teruggevallen op de CPU die al het werk moet doen. Dit kan dus zeer vertragend werken, zeker als je CPU niet te snel is.

De optimalisatie binnen 13.04 waarover gerept wordt. is er wel degelijk (ik draai op verschillende machines 13.04 en het verschil is goed merkbaar), maar daar heb je niets aan als je kaart geen 3D ondersteunt.

Remedie: kijk of je 3D bij je videokaart aangeslingerd kan krijgen. Eventueel uitwisselen van een kaart die (onder 13.04)  3D aankan. Of terugvallen naar 12.04 waar je een 2D-fallback hebt: wat voor videokaart je ook hebt, het draait altijd, zonder morren.

Offline Pjotr

  • Lid
    • Makkelijke Linuxtips
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #7 Gepost op: 2013/06/19, 09:59:31 »
Zoals aartje al zegt: eerst moeten we precies weten wat voor vlees we in de kuip hebben.

Doe dus eens wat aartje al suggereerde:
https://sites.google.com/site/computertip/tipsentrucs#TOC-Maak-automatisch-een-handig-overzicht-van-de-apparatuur-in-uw-computer
(punt 18, rechterkolom)
« Laatst bewerkt op: 2013/06/19, 10:01:43 door Pjotr »

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #8 Gepost op: 2013/06/19, 23:59:13 »
Sorry het is een hele lap tekst geworden   =D

id:
description: Mini Towercomputer
product: OptiPlex 745 ()
vendor: Winbond Electronics
serial: FFBVP2J
width: 64 bits
capabilities: smbios-2.3 dmi-2.3 vsyscall32
configuration:
administrator_password = enabled
boot = normal
chassis = mini-tower
power-on_password = enabled
uuid = 44454C4C-4600-1042-8056-C6C04F50324A
id:
core
description: Moederbord
product: 0RF703
vendor: Winbond Electronics
physical id:
0
serial: ..CN137406C40074.
id:
firmware
description: BIOS
vendor: Winbond Electronics
physical id:
0
version: 2.0.8
date: 11/30/2006
size: 64KiB
capacity: 960KiB
capabilities: pci pnp apm upgrade shadowing cdboot bootselect edd int13floppytoshiba int5printscreen int9keyboard int14serial int17printer acpi usb ls120boot biosbootspecification netboot
id:
cpu
description: CPU
product: Intel(R) Pentium(R) D CPU 2.80GHz
vendor: Intel Corp.
physical id:
400
bus info:
cpu@0
slot: Microprocessor
size: 2800MHz
width: 64 bits
clock: 800MHz
capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx constant_tsc pebs bts nopl pni dtes64 monitor ds_cpl cid cx16 xtpr lahf_lm
configuration:
cores = 2
enabledcores = 2
threads = 2
id:
cache:0
description: L1 cache
physical id:
700
size: 16KiB
capacity: 16KiB
capabilities: internal write-back data
id:
cache:1
description: L2 cache
physical id:
701
size: 2MiB
capacity: 2MiB
capabilities: internal varies unified
id:
memory
description: System Memory
physical id:
1000
slot: Systeem- of moederbord
size: 2GiB
id:
bank:0
description: DIMM DDR Synchroon 800 MHz (1,2 ns) [empty]
vendor: FFFFFFFFFFFFFFFF
physical id:
0
serial: FFFFFFFF
slot: DIMM_1
width: 64 bits
clock: 800MHz (1.2ns)
id:
bank:1
description: DIMM DDR Synchroon 800 MHz (1,2 ns)
product: TMS2GB264D082805EQ
vendor: 7F7F7F5800000000
physical id:
1
serial: 00000000
slot: DIMM_3
size: 2GiB
width: 64 bits
clock: 800MHz (1.2ns)
id:
bank:2
description: DIMM DDR Synchroon 800 MHz (1,2 ns) [empty]
vendor: FFFFFFFFFFFFFFFF
physical id:
2
serial: FFFFFFFF
slot: DIMM_2
width: 64 bits
clock: 800MHz (1.2ns)
id:
bank:3
description: DIMM DDR Synchroon 800 MHz (1,2 ns) [empty]
vendor: FFFFFFFFFFFFFFFF
physical id:
3
serial: FFFFFFFF
slot: DIMM_4
width: 64 bits
clock: 800MHz (1.2ns)
id:
pci
description: Host bridge
product: 82Q963/Q965 Memory Controller Hub
vendor: Intel Corporation
physical id:
100
bus info:
pci@0000:00:00.0
version: 02
width: 32 bits
clock: 33MHz
configuration:
driver = agpgart-intel
resources:
irq : 0
id:
display:0
description: VGA compatible controller
product: 82Q963/Q965 Integrated Graphics Controller
vendor: Intel Corporation
physical id:
2
bus info:
pci@0000:00:02.0
version: 02
width: 64 bits
clock: 33MHz
capabilities: msi pm vga_controller bus_master cap_list rom
configuration:
driver = i915
latency = 0
resources:
irq : 42
memory : dfe00000-dfefffff
memory : c0000000-cfffffff
ioport : ecb8(size=8)
id:
display:1
description: Display controller
product: 82Q963/Q965 Integrated Graphics Controller
vendor: Intel Corporation
physical id:
2.1
bus info:
pci@0000:00:02.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list
configuration:
latency = 0
resources:
memory : dff00000-dfffffff
id:
usb:0
description: USB controller
product: 82801H (ICH8 Family) USB UHCI Controller #4
vendor: Intel Corporation
physical id:
1a
bus info:
pci@0000:00:1a.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration:
driver = uhci_hcd
latency = 0
resources:
irq : 16
ioport : ff20(size=32)
id:
usb:1
description: USB controller
product: 82801H (ICH8 Family) USB UHCI Controller #5
vendor: Intel Corporation
physical id:
1a.1
bus info:
pci@0000:00:1a.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration:
driver = uhci_hcd
latency = 0
resources:
irq : 17
ioport : ff00(size=32)
id:
usb:2
description: USB controller
product: 82801H (ICH8 Family) USB2 EHCI Controller #2
vendor: Intel Corporation
physical id:
1a.7
bus info:
pci@0000:00:1a.7
version: 02
width: 32 bits
clock: 33MHz
capabilities: pm debug ehci bus_master cap_list
configuration:
driver = ehci_hcd
latency = 0
resources:
irq : 22
memory : dfdfbc00-dfdfbfff
id:
multimedia
description: Audio device
product: 82801H (ICH8 Family) HD Audio Controller
vendor: Intel Corporation
physical id:
1b
bus info:
pci@0000:00:1b.0
version: 02
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list
configuration:
driver = snd_hda_intel
latency = 0
resources:
irq : 44
memory : dfdfc000-dfdfffff
id:
pci:0
description: PCI bridge
product: 82801H (ICH8 Family) PCI Express Port 1
vendor: Intel Corporation
physical id:
1c
bus info:
pci@0000:00:1c.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
configuration:
driver = pcieport
resources:
irq : 40
ioport : 3000(size=4096)
memory : dfc00000-dfcfffff
ioport : 80200000(size=2097152)
id:
pci:1
description: PCI bridge
product: 82801H (ICH8 Family) PCI Express Port 5
vendor: Intel Corporation
physical id:
1c.4
bus info:
pci@0000:00:1c.4
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress msi pm normal_decode bus_master cap_list
configuration:
driver = pcieport
resources:
irq : 41
ioport : 1000(size=4096)
memory : dfb00000-dfbfffff
ioport : 80000000(size=2097152)
id:
network
description: Ethernet interface
product: NetXtreme BCM5754 Gigabit Ethernet PCI Express
vendor: Broadcom Corporation
physical id:
0
bus info:
pci@0000:02:00.0
logical name:
eth0
version: 02
serial: 00:19:b9:12:d4:db
size: 100Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration:
autonegotiation = on
broadcast = yes
driver = tg3
driverversion = 3.121
duplex = full
firmware = 5754-v3.15
latency = 0
link = yes
multicast = yes
port = twisted pair
speed = 100Mbit/s
resources:
irq : 43
memory : dfbf0000-dfbfffff
id:
usb:3
description: USB controller
product: 82801H (ICH8 Family) USB UHCI Controller #1
vendor: Intel Corporation
physical id:
1d
bus info:
pci@0000:00:1d.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration:
driver = uhci_hcd
latency = 0
resources:
irq : 23
ioport : ff80(size=32)
id:
usb:4
description: USB controller
product: 82801H (ICH8 Family) USB UHCI Controller #2
vendor: Intel Corporation
physical id:
1d.1
bus info:
pci@0000:00:1d.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration:
driver = uhci_hcd
latency = 0
resources:
irq : 17
ioport : ff60(size=32)
id:
usb:5
description: USB controller
product: 82801H (ICH8 Family) USB UHCI Controller #3
vendor: Intel Corporation
physical id:
1d.2
bus info:
pci@0000:00:1d.2
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration:
driver = uhci_hcd
latency = 0
resources:
irq : 18
ioport : ff40(size=32)
id:
usb:6
description: USB controller
product: 82801H (ICH8 Family) USB2 EHCI Controller #1
vendor: Intel Corporation
physical id:
1d.7
bus info:
pci@0000:00:1d.7
version: 02
width: 32 bits
clock: 33MHz
capabilities: pm debug ehci bus_master cap_list
configuration:
driver = ehci_hcd
latency = 0
resources:
irq : 23
memory : ff980800-ff980bff
id:
pci:2
description: PCI bridge
product: 82801 PCI Bridge
vendor: Intel Corporation
physical id:
1e
bus info:
pci@0000:00:1e.0
version: f2
width: 32 bits
clock: 33MHz
capabilities: pci subtractive_decode bus_master cap_list
id:
isa
description: ISA bridge
product: 82801HB/HR (ICH8/R) LPC Interface Controller
vendor: Intel Corporation
physical id:
1f
bus info:
pci@0000:00:1f.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: isa bus_master cap_list
configuration:
latency = 0
id:
ide:0
description: IDE interface
product: 82801H (ICH8 Family) 4 port SATA Controller [IDE mode]
vendor: Intel Corporation
physical id:
1f.2
bus info:
pci@0000:00:1f.2
logical name:
scsi0
logical name:
scsi1
version: 02
width: 32 bits
clock: 66MHz
capabilities: ide pm bus_master cap_list emulated
configuration:
driver = ata_piix
latency = 0
resources:
irq : 20
ioport : fe00(size=8)
ioport : fe10(size=4)
ioport : fe20(size=8)
ioport : fe30(size=4)
ioport : fec0(size=16)
ioport : ecc0(size=16)
id:
disk
description: ATA Disk
product: WDC WD800JD-75MS
vendor: Western Digital
physical id:
0
bus info:
scsi@0:0.0.0
logical name:
/dev/sda
version: 10.0
serial: WD-WMAM9LK44810
size: 74GiB (80GB)
capabilities: partitioned partitioned:dos
configuration:
ansiversion = 5
signature = 000e1f16
id:
volume:0
description: EXT4 volume
vendor: Linux
physical id:
1
bus info:
scsi@0:0.0.0,1
logical name:
/dev/sda1
logical name:
/
version: 1.0
serial: cfb943aa-1f3e-4414-8326-65f02566d3fc
size: 72GiB
capacity: 72GiB
capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized
configuration:
created = 2012-05-14 09:05:48
filesystem = ext4
lastmountpoint = /
modified = 2013-02-09 15:36:26
mount.fstype = ext4
mount.options = rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered
mounted = 2013-06-19 13:13:39
state = mounted
id:
volume:1
description: Extended partition
physical id:
2
bus info:
scsi@0:0.0.0,2
logical name:
/dev/sda2
size: 2036MiB
capacity: 2036MiB
capabilities: primary extended partitioned partitioned:extended
id:
logicalvolume
description: Linux swap / Solaris partition
physical id:
5
logical name:
/dev/sda5
capacity: 2036MiB
capabilities: nofs
id:
cdrom
description: DVD reader
product: DVD-ROM DDU1615S
vendor: SONY
physical id:
1
bus info:
scsi@1:0.0.0
logical name:
/dev/cdrom
logical name:
/dev/dvd
logical name:
/dev/sr0
version: EDS3
capabilities: removable audio dvd
configuration:
ansiversion = 5
status = nodisc
id:
serial
description: SMBus
product: 82801H (ICH8 Family) SMBus Controller
vendor: Intel Corporation
physical id:
1f.3
bus info:
pci@0000:00:1f.3
version: 02
width: 32 bits
clock: 33MHz
configuration:
latency = 0
resources:
memory : dfdfbb00-dfdfbbff
ioport : ece0(size=32)
id:
ide:1
description: IDE interface
product: 82801HR/HO/HH (ICH8R/DO/DH) 2 port SATA Controller [IDE mode]
vendor: Intel Corporation
physical id:
1f.5
bus info:
pci@0000:00:1f.5
version: 02
width: 32 bits
clock: 66MHz
capabilities: ide pm bus_master cap_list
configuration:
driver = ata_piix
latency = 0
resources:
irq : 20
ioport : fe40(size=8)
ioport : fe50(size=4)
ioport : fe60(size=8)
ioport : fe70(size=4)
ioport : fed0(size=16)
ioport : ecd0(size=16)
id:
network
description: Ethernet interface
physical id:
1
logical name:
eth1
serial: 00:1b:fc:17:72:67
capabilities: ethernet physical
configuration:
broadcast = yes
driver = cdc_ether
driverversion = 22-Aug-2005
firmware = CDC Ethernet Device
ip = 192.168.1.6
link = yes
multicast = yes
Ubuntu 18.04

Intel Skylake i3 6100, 8 GB DDR4, nVidia Geforce GTX 750 ti (2GB)

Offline jan11000

  • Lid
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #9 Gepost op: 2013/06/20, 05:46:26 »
Software center is zwaar, zeker met starten.(dacht dat ze dit gingen optimalizeren, welke ubuntu weet ik niet?).
Dash maakt veel verbindingen, en veel zoek werk op de achtergrond/internet.

Installeer xubuntu, deze heeft geen dash, dus probleem van de dash is dan weg.
Software center is hetzelfde.
Alle software die je in ubuntu kunt installeren kun je ook in xubuntu installeren.
Xubuntu is lichter , reageert sneller.
Zelf heb ik een i7 920 met 6 GB, en draai xubuntu, lekker snel.

En als je een pc koopt, maak een lijst met je hardware, en niet een lange print waar je 10 minuten moet gaan lezen om te kijken wat voor hardware je hebt, terwijl jij dat zelf zou moet uitzoeken. En 10 minuten gaan lezen doe ik niet met zo een file.
Dus maak een lijst,
cpu
moederbord
videokaart/ en of deze onboard is
geheugen, hoeveel dus
voeding/en hier ook merk vermelden(dit is het belangrijkste van je hele pc)
Andere hardware

En zoals je ziet is zo een lange lijst niet nodig.
En vaak is deze info nodig om vragen te beantwoorden, dus altijd meegeven is vaak handig.
« Laatst bewerkt op: 2013/06/20, 05:51:18 door jan11000 »

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #10 Gepost op: 2013/06/20, 06:49:57 »
Jan, dit kan ik beamen. Ik heb sinds 2 dagen de Xubuntu shell over mijn Ubuntu 13.04 gezet en het draait inderdaad een heel stuk fijner (zie topic wat ik eerder aangaf met een soortgelijke uitdaging).

Gr. Mischa

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #11 Gepost op: 2013/06/20, 09:44:46 »
software centrum loopt bij mij ook regelmatig vast, zelfs met specs van 'tegenwoordig' ( amd a8-4500 & 8gb ram) maar ook op elke andere pc in mijn omgeving, dus als je het mij vraagt is software centrum gewoon een en all onstabiel.

Offline DeBaas

  • Lid
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #12 Gepost op: 2013/06/20, 10:47:23 »
82Q963/Q965 Integrated Graphics Controller

Deze machine gaat voor Ubuntu nog mee tot april 2017, mits.........
maximaal 12.04.1 LTS
Daarna loop je risico met te nieuwe xorg, video drivers, kernel en voor jouw video te zware desktop.
In 12.04.1 wordt je weliswaar ge-update naar 12.04.2(en verder) maar blijft video in tact.
Voor een snellere desktop afhandeling kun je de 2D omgeving of (versie gelijkwaardige) LXDE of XFCE kiezen. (Lubuntu/Xubuntu)
Zelfs mijn 3 jaar oude Vaio portable geeft het met ingang van 12.04.2, qua video driver, op in 3D.
Dus al is de 13 versie beter geoptimaliseerd, zoniet voor oudere PC dozen en draagbakjes.

Mijn ervaring... 2 centen, doe er mee wat u goeddunkt.
Ed
Ik beantwoord GEEN hulpvragen via PB en/of MAIL

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #13 Gepost op: 2013/06/21, 18:59:22 »
Bedankt voor alle reacties. Leuk om te lezen  :)

Ik heb totaal geen verstand van hardware maar zoals ik het nu begrijp is mijn huidige Ubuntu 12.04 installatie te zwaar voor mijn computer. Toch?

Een nieuwe installatie van Xubuntu ga ik vanwege tijdgebrek nog eventjes uit de weg. Maar wie weet  ;)

Citaat
Ik heb sinds 2 dagen de Xubuntu shell over mijn Ubuntu 13.04 gezet en het draait inderdaad een heel stuk fijner

Ook een overweging waard al neig ik zelf naar een schone installatie. 

Even een ´noob´ vraag   :-[ als ik kies om Xubuntu over mijn huidige OS te zetten ben ik dan ook al mijn programma´s kwijt? Ik gebruik ook nog Virtualbox met allerlei  Windows programma´s daarin. Alles op nieuw installeren kost dan wel erg veel tijd. 
Ubuntu 18.04

Intel Skylake i3 6100, 8 GB DDR4, nVidia Geforce GTX 750 ti (2GB)

Offline DeBaas

  • Lid
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #14 Gepost op: 2013/06/21, 19:13:12 »
De VirtualBox images, de .vdi files, kun je copieeren, na installatie terugzetten en weer aan VB koppelen.
Ik beantwoord GEEN hulpvragen via PB en/of MAIL

Offline jan11000

  • Lid
Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #15 Gepost op: 2013/06/21, 19:16:53 »
Xubuntu kun je gewoon erbij zetten.
Dan bij boot, waar je inlogd, daar kun je kiezen voor xubuntu.

http://www.psychocats.net/ubuntu/xubuntu
Of eerst updaten, en via software center  "xubuntu-desktop" installeren.
Dan rebooten en voor xubuntu kiezen bij inloggen.
Je kunt dezelfde programma's blijven gebruiken.
« Laatst bewerkt op: 2013/06/21, 19:19:21 door jan11000 »

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #16 Gepost op: 2013/06/21, 19:34:15 »
Een nieuwe installatie van Xubuntu ga ik vanwege tijdgebrek nog eventjes uit de weg. Maar wie weet  ;)

Een nieuwe installatie duurt een klein half uurtje. Je bent geen Windows aan het installeren hé  =D
Zoals DeBaas al schreef zou ik die files copieren.
Best is nog altijd een clean install te doen.
Linux Mint 18.3  Xfce

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #17 Gepost op: 2013/06/23, 09:49:05 »
Als ik tijd heb dan ga ik Xubuntu installeren. Ik vind het wel tricky want ik heb een webshop. Dus ik maak liever geen rare/onvoorziene fouten.

In eerste instantie wil ik nog even kijken hoe het gaat als ik 3D-effecten uitschakel. Inmiddels wel de nodige bestanden verwijderd,  prullenpak geleegd, bestanden die ik niet gebruik maar wel wil bewaren gezipt. Computer reageert een stuk sneller. 

Citaat
Een nieuwe installatie duurt een klein half uurtje.
Het uitzoeken/inlezen over hoe ik een installatie doe, welk systeem ik moet kiezen kost de meeste tijd.

PS. Net nog even  een Windows XP virtual machine verwijderd en een nieuwe installatie gedaan. Duurt niet zo heel lang hoor maar langer dan 30 minuten.
Ubuntu 18.04

Intel Skylake i3 6100, 8 GB DDR4, nVidia Geforce GTX 750 ti (2GB)

Re: Dash-home en software centrum te zwaar voor mijn computer?
« Reactie #18 Gepost op: 2013/06/23, 10:09:49 »
Citaat
Xubuntu kun je gewoon erbij zetten.
Dan bij boot, waar je inlogd, daar kun je kiezen voor xubuntu.

Mijn idee: voor de veiligheid eerst Xubuntu installeren naast Ubuntu 12.04. Alles alles goed werkt Ubuntu 12.04 verwijderen.

Goed idee?
Ubuntu 18.04

Intel Skylake i3 6100, 8 GB DDR4, nVidia Geforce GTX 750 ti (2GB)