Hoi,ik heb ook een probleem met mijn cardreader het is een alles in een lezer.
Deze zit ingebouwd in mijn pc.
Maar mijn sdcard van 4gb wordt niet herkend als extra opslagmedium.
Althans ik kan nergens een extra sda drive vinden bij de mount.
Het lampje van de usb2.0 aansluiting brand constant op mijn kaartlezer.
Wanneer ik mijn sdcard in het daarvoor bestemde slot steek brand er even een ander lampje wel even,en gaat dan weer uit.
Voor de duidelijkheid ik heb een Asus p5k-vm moederbord.
Core 2 duo E8200 processor 2,66 ghz 6mb cache op een bussnelheid van 1333 mhz
daarop 4gb intern geheugen.
Samsung 320gb hd
Lite-on dvdbrander lh-20a1s
---------------------------------
Ik heb dus gekeken met mount.
Dan krijg ik dit te zien.
/dev/sda5 on / type reiserfs (rw,relatime)
proc on /proc type proc (rw,noexec,nosuid,nodev)
/sys on /sys type sysfs (rw,noexec,nosuid,nodev)
varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755)
varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777)
udev on /dev type tmpfs (rw,mode=0755)
devshm on /dev/shm type tmpfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
lrm on /lib/modules/2.6.24-20-generic/volatile type tmpfs (rw)
/dev/sda1 on /boot type ext3 (rw,relatime)
/dev/sda6 on /home type reiserfs (rw,relatime)
securityfs on /sys/kernel/security type securityfs (rw)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev)
gvfs-fuse-daemon on /home/merijn/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=merijn)
en als ik alles controleer met,dmesg dan krijg ik dit.
Ik kan allemaal niet uit de meldingen komen.
Misschien weet iemand wat er aan de hand kan zijn.
--------------------------------------------------
)
[ 24.210344] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 24.211225] Mount-cache hash table entries: 256
[ 24.211322] Initializing cgroup subsys ns
[ 24.211326] Initializing cgroup subsys cpuacct
[ 24.211338] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 24.211339] CPU: L2 cache: 6144K
[ 24.211341] CPU 0/0 -> Node 0
[ 24.211342] using mwait in idle threads.
[ 24.211344] CPU: Physical Processor ID: 0
[ 24.211345] CPU: Processor Core ID: 0
[ 24.211349] CPU0: Thermal monitoring enabled (TM2)
[ 24.211360] SMP alternatives: switching to UP code
[ 24.212056] Early unpacking initramfs... done
[ 24.470598] ACPI: Core revision 20070126
[ 24.470637] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 24.535427] Using local APIC timer interrupts.
[ 24.572929] APIC timer calibration result 20832937
[ 24.572930] Detected 20.832 MHz APIC timer.
[ 24.572985] SMP alternatives: switching to SMP code
[ 24.573592] Booting processor 1/2 APIC 0x1
[ 24.584217] Initializing CPU#1
[ 24.676931] Calibrating delay using timer specific routine.. 5333.22 BogoMIPS (lpj=10666456)
[ 24.676936] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 24.676937] CPU: L2 cache: 6144K
[ 24.676938] CPU 1/1 -> Node 0
[ 24.676939] CPU: Physical Processor ID: 0
[ 24.676940] CPU: Processor Core ID: 1
[ 24.676944] CPU1: Thermal monitoring enabled (TM2)
[ 24.677637] Intel(R) Core(TM)2 Duo CPU E8200 @ 2.66GHz stepping 06
[ 24.677739] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 24.697756] Brought up 2 CPUs
[ 24.697816] CPU0 attaching sched-domain:
[ 24.697817] domain 0: span 03
[ 24.697818] groups: 01 02
[ 24.697820] domain 1: span 03
[ 24.697821] groups: 03
[ 24.697822] CPU1 attaching sched-domain:
[ 24.697823] domain 0: span 03
[ 24.697824] groups: 02 01
[ 24.697825] domain 1: span 03
[ 24.697826] groups: 03
[ 24.697990] net_namespace: 120 bytes
[ 24.698244] Time: 12:28:03 Date: 07/24/08
[ 24.698263] NET: Registered protocol family 16
[ 24.698394] ACPI: bus type pci registered
[ 24.698444] PCI: Using configuration type 1
[ 24.700742] ACPI: EC: Look up EC in DSDT
[ 24.705860] ACPI: Interpreter enabled
[ 24.705862] ACPI: (supports S0 S1 S3 S4 S5)
[ 24.705873] ACPI: Using IOAPIC for interrupt routing
[ 24.712463] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 24.713068] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 24.713070] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[ 24.713649] PCI: Transparent bridge - 0000:00:1e.0
[ 24.713672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 24.713787] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 24.713853] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 24.713941] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 24.714008] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 24.714083] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 24.727111] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 24.727202] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 24.727292] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 24.727382] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 24.727471] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 24.727560] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 24.727649] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 24.727738] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 *14 15)
[ 24.727824] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - FB, should be F6 [20070126]
[ 24.727834] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 24.727853] pnp: PnP ACPI init
[ 24.727858] ACPI: bus type pnp registered
[ 24.730794] pnp: PnP ACPI: found 15 devices
[ 24.730796] ACPI: ACPI bus type pnp unregistered
[ 24.730952] PCI: Using ACPI for IRQ routing
[ 24.730953] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 24.744953] NET: Registered protocol family 8
[ 24.744955] NET: Registered protocol family 20
[ 24.744983] PCI-GART: No AMD northbridge found.
[ 24.744987] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 24.744990] hpet0: 4 64-bit timers, 14318180 Hz
[ 24.746013] AppArmor: AppArmor Filesystem Enabled
[ 24.748931] Time: tsc clocksource has been installed.
[ 24.748937] Switched to high resolution mode on CPU 0
[ 24.749750] Switched to high resolution mode on CPU 1
[ 24.756927] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[ 24.756934] system 00:07: ioport range 0x290-0x297 has been reserved
[ 24.756939] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 24.756941] system 00:08: ioport range 0x800-0x87f has been reserved
[ 24.756943] system 00:08: ioport range 0x480-0x4bf has been reserved
[ 24.756946] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 24.756948] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 24.756951] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
[ 24.756953] system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
[ 24.756956] system 00:08: iomem range 0xfff00000-0xfffffffe could not be reserved
[ 24.756961] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[ 24.756964] system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 24.756969] system 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
[ 24.756973] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 24.756976] system 00:0e: iomem range 0xc0000-0xcffff has been reserved
[ 24.756978] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[ 24.756981] system 00:0e: iomem range 0x100000-0xcfffffff could not be reserved
[ 24.756983] system 00:0e: iomem range 0x0-0x0 could not be reserved
[ 24.757250] PCI: Bridge: 0000:00:01.0
[ 24.757251] IO window: b000-bfff
[ 24.757253] MEM window: fa000000-fe9fffff
[ 24.757255] PREFETCH window: d0000000-dfffffff
[ 24.757257] PCI: Bridge: 0000:00:1c.0
[ 24.757258] IO window: disabled.
[ 24.757260] MEM window: disabled.
[ 24.757262] PREFETCH window: f8f00000-f8ffffff
[ 24.757266] PCI: Bridge: 0000:00:1c.4
[ 24.757267] IO window: d000-dfff
[ 24.757270] MEM window: disabled.
[ 24.757272] PREFETCH window: disabled.
[ 24.757275] PCI: Bridge: 0000:00:1c.5
[ 24.757276] IO window: c000-cfff
[ 24.757279] MEM window: fea00000-feafffff
[ 24.757281] PREFETCH window: disabled.
[ 24.757284] PCI: Bridge: 0000:00:1e.0
[ 24.757285] IO window: e000-efff
[ 24.757288] MEM window: feb00000-febfffff
[ 24.757290] PREFETCH window: disabled.
[ 24.757300] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 24.757303] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 24.757314] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 24.757318] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 24.757329] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
[ 24.757332] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 24.757343] ACPI: PCI Interrupt 0000:00:1c.5 -> GSI 16 (level, low) -> IRQ 16
[ 24.757346] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 24.757353] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 24.757359] NET: Registered protocol family 2
[ 24.793017] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 24.793727] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 24.796229] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 24.796664] TCP: Hash tables configured (established 524288 bind 65536)
[ 24.796665] TCP reno registered
[ 24.805041] checking if image is initramfs... it is
[ 25.314090] Freeing initrd memory: 7544k freed
[ 25.316428] audit: initializing netlink socket (disabled)
[ 25.316444] audit(1216902483.164:1): initialized
[ 25.317867] VFS: Disk quotas dquot_6.5.1
[ 25.317913] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 25.317996] io scheduler noop registered
[ 25.317997] io scheduler anticipatory registered
[ 25.317998] io scheduler deadline registered
[ 25.318062] io scheduler cfq registered (default)
[ 25.323250] Boot video device is 0000:01:00.0
[ 25.323364] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 25.323383] assign_interrupt_mode Found MSI capability
[ 25.323401] Allocate Port Service[0000:00:01.0:pcie00]
[ 25.323449] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 25.323477] assign_interrupt_mode Found MSI capability
[ 25.323499] Allocate Port Service[0000:00:1c.0:pcie00]
[ 25.323521] Allocate Port Service[0000:00:1c.0:pcie02]
[ 25.323573] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 25.323601] assign_interrupt_mode Found MSI capability
[ 25.323623] Allocate Port Service[0000:00:1c.4:pcie00]
[ 25.323643] Allocate Port Service[0000:00:1c.4:pcie02]
[ 25.323699] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 25.323726] assign_interrupt_mode Found MSI capability
[ 25.323748] Allocate Port Service[0000:00:1c.5:pcie00]
[ 25.323767] Allocate Port Service[0000:00:1c.5:pcie02]
[ 25.339231] Real Time Clock Driver v1.12ac
[ 25.339351] hpet_resources: 0xfed00000 is busy
[ 25.339378] Linux agpgart interface v0.102
[ 25.339379] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 25.339475] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 25.339827] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 25.340274] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 25.340313] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 25.340367] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 25.340369] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 25.340842] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 25.357431] mice: PS/2 mouse device common for all mice
[ 25.357459] cpuidle: using governor ladder
[ 25.357461] cpuidle: using governor menu
[ 25.357552] NET: Registered protocol family 1
[ 25.357613] registered taskstats version 1
[ 25.357690] Magic number: 0:9:482
[ 25.357719] /build/buildd/linux-2.6.24/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 25.357721] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 25.357722] EDD information not available.
[ 25.357728] Freeing unused kernel memory: 320k freed
[ 25.387174] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 26.474049] fuse init (API version 7.9)
[ 26.484636] ACPI: SSDT CFF90100, 01D2 (r1 AMI CPU1PM 1 INTL 20060113)
[ 26.485059] ACPI: SSDT CFF902E0, 0143 (r1 AMI CPU2PM 1 INTL 20060113)
[ 26.485384] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 26.485390] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 26.545504] usbcore: registered new interface driver usbfs
[ 26.545518] usbcore: registered new interface driver hub
[ 26.545533] usbcore: registered new device driver usb
[ 26.545986] USB Universal Host Controller Interface driver v3.0
[ 26.546021] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 26.546029] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 26.546031] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 26.546157] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 26.546178] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800
[ 26.546250] usb usb1: configuration #1 chosen from 1 choice
[ 26.546263] hub 1-0:1.0: USB hub found
[ 26.546267] hub 1-0:1.0: 2 ports detected
[ 26.649345] ACPI: PCI Interrupt 0000:00:1a.1 -> GSI 21 (level, low) -> IRQ 21
[ 26.649354] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 26.649356] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 26.649372] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 26.649394] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[ 26.649459] usb usb2: configuration #1 chosen from 1 choice
[ 26.649473] hub 2-0:1.0: USB hub found
[ 26.649476] hub 2-0:1.0: 2 ports detected
[ 26.684714] SCSI subsystem initialized
[ 26.703424] libata version 3.00 loaded.
[ 26.753361] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 26.753371] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 26.753373] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 26.753388] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 26.753410] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00
[ 26.753477] usb usb3: configuration #1 chosen from 1 choice
[ 26.753493] hub 3-0:1.0: USB hub found
[ 26.753497] hub 3-0:1.0: 2 ports detected
[ 26.857353] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 26.858668] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 26.858672] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 26.858708] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 4
[ 26.862618] ehci_hcd 0000:00:1a.7: debug port 1
[ 26.862622] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 26.862627] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
[ 26.876765] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 26.876834] usb usb4: configuration #1 chosen from 1 choice
[ 26.876849] hub 4-0:1.0: USB hub found
[ 26.876853] hub 4-0:1.0: 6 ports detected
[ 26.980826] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 26.982069] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 26.982074] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 26.982117] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 26.986029] ehci_hcd 0000:00:1d.7: debug port 1
[ 26.986033] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 26.986040] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
[ 27.000756] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 27.000844] usb usb5: configuration #1 chosen from 1 choice
[ 27.000868] hub 5-0:1.0: USB hub found
[ 27.000872] hub 5-0:1.0: 6 ports detected
[ 27.104834] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 27.105182] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 27.105189] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 27.105191] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 27.105203] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 27.105222] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080
[ 27.105280] usb usb6: configuration #1 chosen from 1 choice
[ 27.105292] hub 6-0:1.0: USB hub found
[ 27.105296] hub 6-0:1.0: 2 ports detected
[ 27.157931] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[febff800-febfffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 27.208796] ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 19
[ 27.208802] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 27.208805] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 27.208821] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 27.208842] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
[ 27.208908] usb usb7: configuration #1 chosen from 1 choice
[ 27.208921] hub 7-0:1.0: USB hub found
[ 27.208925] hub 7-0:1.0: 2 ports detected
[ 27.312781] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 27.312787] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 27.312790] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 27.312804] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 27.312823] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480
[ 27.312890] usb usb8: configuration #1 chosen from 1 choice
[ 27.312902] hub 8-0:1.0: USB hub found
[ 27.312906] hub 8-0:1.0: 2 ports detected
[ 27.417477] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 22 (level, low) -> IRQ 22
[ 27.417496] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 27.417503] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[ 27.417516] ACPI: PCI Interrupt 0000:00:1f.5 -> GSI 22 (level, low) -> IRQ 22
[ 27.417529] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 27.417534] ACPI: PCI interrupt for device 0000:00:1f.5 disabled
[ 27.417553] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 27.417570] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 27.417578] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[ 27.420935] ata_piix 0000:00:1f.2: version 2.12
[ 27.420939] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 27.420949] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 22 (level, low) -> IRQ 22
[ 27.420965] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 27.421945] scsi0 : ata_piix
[ 27.422599] scsi1 : ata_piix
[ 27.423418] ata1: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 22
[ 27.423420] ata2: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 22
[ 27.600987] ata1.00: ATA-8: SAMSUNG HD321KJ, CP100-12, max UDMA7
[ 27.600990] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 27.609482] ata1.00: configured for UDMA/133
[ 27.812698] usb 5-3: new high speed USB device using ehci_hcd and address 2
[ 27.944857] ata2.00: ATAPI: LITE-ON DVDRW LH-20A1S, 9L09, max UDMA/100
[ 27.946757] usb 5-3: configuration #1 chosen from 1 choice
[ 28.073226] usbcore: registered new interface driver libusual
[ 28.075779] Initializing USB Mass Storage driver...
[ 28.132842] ata2.00: configured for UDMA/100
[ 28.132907] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD321KJ CP10 PQ: 0 ANSI: 5
[ 28.134086] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1S 9L09 PQ: 0 ANSI: 5
[ 28.134137] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 28.134151] ACPI: PCI Interrupt 0000:00:1f.5 -> GSI 22 (level, low) -> IRQ 22
[ 28.134172] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 28.134197] scsi2 : ata_piix
[ 28.134219] scsi3 : ata_piix
[ 28.134904] ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 22
[ 28.134906] ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 22
[ 28.313157] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 28.432710] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c0001102e03]
[ 28.463748] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 28.463773] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 28.463961] scsi4 : pata_jmicron
[ 28.464191] scsi5 : pata_jmicron
[ 28.464448] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 16
[ 28.464450] ata6: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 16
[ 28.469476] Driver 'sd' needs updating - please use bus_type methods
[ 28.469901] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 28.469908] sd 0:0:0:0: [sda] Write Protect is off
[ 28.469909] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 28.469919] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.469950] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 28.469955] sd 0:0:0:0: [sda] Write Protect is off
[ 28.469957] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 28.469966] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.469969] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 28.471434] usb 2-1: configuration #1 chosen from 1 choice
[ 28.500502] sda1 sda2 < sda5 sda6 sda7 >
[ 28.546261] sd 0:0:0:0: [sda] Attached SCSI disk
[ 28.548534] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 28.548544] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 28.557568] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 28.557570] Uniform CD-ROM driver Revision: 3.20
[ 28.557593] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 28.717129] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 28.805676] Attempting manual resume
[ 28.805677] swsusp: Resume From Partition 8:7
[ 28.805678] PM: Checking swsusp image.
[ 28.805827] PM: Resume from disk failed.
[ 28.809827] ReiserFS: sda5: found reiserfs format "3.6" with standard journal
[ 28.809832] ReiserFS: sda5: using ordered data mode
[ 28.831711] ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 28.831989] ReiserFS: sda5: checking transaction log (sda5)
[ 28.857194] ReiserFS: sda5: Using r5 hash to sort names
[ 28.893470] usb 3-2: configuration #1 chosen from 1 choice
[ 28.896491] scsi6 : SCSI emulation for USB Mass Storage devices
[ 28.896537] usbcore: registered new interface driver usb-storage
[ 28.896539] USB Mass Storage support registered.
[ 28.896604] usb-storage: device found at 2
[ 28.896606] usb-storage: waiting for device to settle before scanning
[ 33.900458] iTCO_vendor_support: vendor-support=0
[ 34.162830] usb-storage: device scan complete
[ 34.174093] scsi 6:0:0:0: Direct-Access AVEX AX1611 CF 1.9C PQ: 0 ANSI: 0 CCS
[ 34.175213] scsi 6:0:0:1: Direct-Access AVEX AX1611 MS 1.9C PQ: 0 ANSI: 0 CCS
[ 34.176464] scsi 6:0:0:2: Direct-Access AVEX AX1611 MMC/SD 1.9C PQ: 0 ANSI: 0 CCS
[ 34.177588] scsi 6:0:0:3: Direct-Access AVEX AX1611 SM 1.9C PQ: 0 ANSI: 0 CCS
[ 34.177816] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 34.177868] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0860)
[ 34.177895] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 34.209727] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 34.209766] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 34.210859] sd 6:0:0:1: [sdc] Attached SCSI removable disk
[ 34.210895] sd 6:0:0:1: Attached scsi generic sg3 type 0
[ 34.212107] sd 6:0:0:2: [sdd] Attached SCSI removable disk
[ 34.212139] sd 6:0:0:2: Attached scsi generic sg4 type 0
[ 34.213253] sd 6:0:0:3: [sde] Attached SCSI removable disk
[ 34.213286] sd 6:0:0:3: Attached scsi generic sg5 type 0
[ 34.219211] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 34.235237] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 34.350507] parport_pc 00:06: reported by Plug and Play ACPI
[ 34.350609] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 34.370262] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 34.452283] input: Power Button (FF) as /devices/virtual/input/input3
[ 34.480695] ACPI: Power Button (FF) [PWRF]
[ 34.480757] input: Power Button (CM) as /devices/virtual/input/input4
[ 34.512688] ACPI: Power Button (CM) [PWRB]
[ 34.688262] nvidia: module license 'NVIDIA' taints kernel.
[ 35.046829] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 35.046836] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 35.046892] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.12 Thu Feb 14 17:51:09 PST 2008
[ 35.114325] usbcore: registered new interface driver hiddev
[ 35.129025] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.2/usb3/3-2/3-2:1.0/input/input5
[ 35.138650] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 35.138662] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 35.139920] sky2 0000:02:00.0: v1.20 addr 0xfeafc000 irq 17 Yukon-EC Ultra (0xb4) rev 3
[ 35.140228] sky2 eth0: addr 00:1e:8c:ec:11:ab
[ 35.175523] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 35.176801] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 35.188674] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.2-2
[ 35.188685] usbcore: registered new interface driver usbhid
[ 35.188688] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 35.210477] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 35.618241] sky2 eth0: enabling interface
[ 36.473780] loop: module loaded
[ 36.486200] lp0: using parport0 (interrupt-driven).
[ 36.575782] Adding 1919728k swap on /dev/sda7. Priority:-1 extents:1 across:1919728k
[ 37.437404] NET: Registered protocol family 17
[ 37.445470] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 43.341265] NET: Registered protocol family 10
[ 43.341400] lo: Disabled Privacy Extensions
[ 53.769511] eth0: no IPv6 routers present
[ 67.232737] kjournald starting. Commit interval 5 seconds
[ 67.240122] EXT3 FS on sda1, internal journal
[ 67.240126] EXT3-fs: mounted filesystem with ordered data mode.
[ 67.253442] ReiserFS: sda6: found reiserfs format "3.6" with standard journal
[ 67.253448] ReiserFS: sda6: using ordered data mode
[ 67.257917] ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 67.258242] ReiserFS: sda6: checking transaction log (sda6)
[ 67.286552] ReiserFS: sda6: Using r5 hash to sort names
[ 67.514729] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 67.542683] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 67.994805] No dock devices found.
[ 68.852447] ppdev: user-space parallel port driver
[ 68.954598] audit(1216895327.549:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5845 profile="/usr/sbin/cupsd" namespace="default"
[ 71.602149] Bluetooth: Core ver 2.11
[ 71.602429] NET: Registered protocol family 31
[ 71.602432] Bluetooth: HCI device and connection manager initialized
[ 71.602434] Bluetooth: HCI socket layer initialized
[ 71.615713] Bluetooth: L2CAP ver 2.9
[ 71.615716] Bluetooth: L2CAP socket layer initialized
[ 71.649305] Bluetooth: RFCOMM socket layer initialized
[ 71.649316] Bluetooth: RFCOMM TTY layer initialized
[ 71.649317] Bluetooth: RFCOMM ver 1.8
[ 3512.959165] gpar2[30111] general protection rip:7ffb654b9796 rsp:7fff72399a48 error:0
merijn@ubuntu:~$
-----------------
goed wat gpar2 is dat weet ik wel,maar die draait niet op het moment,maar als ik er mee werk dan doet dat programma het gewoon wel goed,met bestanden van de nieuwsgroepen repareren.
Dus daar kan het niet aan liggen.
Voor de duidlijkheid werk ik dus met Ubuntu Hardy X64 8.0.4.1
Wie o wie kan mij misschien antwoord geven,bedankt.