Ik heb het bestand uitgepakt dit is de readme file:
# ============================ Driver Version ============================= #
# = = #
# = eGalax Touch driver for 32bit Linux kernel 2.6.x = #
# = = #
# = Driver version: 3.02.4315-32b-k26 = #
# = Module version: 3.02 = #
# = Utilty version: 3.02.4307 = #
# = released date: 2010/07/15 = #
# = support: touch_fae@eeti.com = #
# =============================== File List =============================== #
(*) Installation with script file:
User can run the "setup.sh" script to install the driver archive
easily in a terminal window.
Syntax:
sh setup.sh # To install the eGalax Touch driver.
or sh setup.sh uninstall # To remove the eGalax Touch driver.
or sh setup.sh version # To get the installer version.
Note that the root permission is required to run this installation
script. Otherwise, below error messages would be popped up.
( Assume, the working distribution is Ubuntu 8.04 )
test@test-desktop:~$ sh setup.sh
(*) Linux driver installer for eGalax Touch controller
(I) Check user permission: test, you are NOT the supervisor.
(E) The root permission is required to run this installer.
The user can get the root permission by the following command.
For example:
su ( For general Linux )
or sudo -s ( For Ubuntu series only )
(*) Driver archive installation:
root@test-desktop:~# sh setup.sh
(*) Linux driver installer for eGalax Touch controller
(I) Check user permission: root, you are the supervisor.
(I) Begin to setup eGalax Touch driver.
(I) Extract eGalax Touch driver archive to /usr/local/eGalaxTouch32.
(I) Create eGalaxTouch utility shortcut in /usr/bin.
(I) Create TKCal tool shortcut in /usr/bin.
(I) Searching the X input modules directory.
(I) Check X window version: 1.4.x
(I) Copy X module: x14/egalax_drv.so to /usr/lib/xorg/modules/input.
(Q) Which interface of controller do you use?
(I) [1] RS232 [2] PS/2 [3] USB: 1
(Q) Which COM port will be connected? e.g. /dev/ttyS0 (COM1)
(A) Please input: /dev/ttyS0
(I) Found X configuration file: /etc/X11/xorg.conf.
(I) Add touch configuration into /etc/X11/xorg.conf.
(I) Please reboot the system for some changes to take effect.
(I) After booting, type "eGalaxTouch" to do calibration.
1. For serial RS232 interface:
(Q) Which interface controller do you use?
(I) [1] RS232 [2] PS/2 [3] USB: 1
(Q) Which COM port will be connected? e.g. /dev/ttyS0 (COM1)
(A) Please input: /dev/ttyS4
Note that the user has to input correct serial device node
where the controller connected.
For example:
/dev/ttyS4 ( Connected to COM5 )
2. For PS/2 interface:
(Q) Which interface controller do you use?
(I) [1] RS232 [2] PS/2 [3] USB: 2
(I) Using interface: PS/2
(I) Please make sure the kernel module for PS/2 controller is available.
(I) For details, see the document "How to rebuild kernel.pdf".
3. For USB interface:
(Q) Which interface controller do you use?
(I) [1] RS232 [2] PS/2 [3] USB: 3
(I) Using interface: USB
(I) Found a HID compliant touch controller.
(I) Found inbuilt kernel module: usbtouchscreen.
(I) It is highly recommended that add it into blacklist.
(Q) Do you want to add it into blacklist? (y/n) y
(I) Add kernel module usbtouchscreen into /etc/modprobe.d/blacklist.
Note that it is highly recommended that add inbuilt kernel module
"usbtouchscreen" or "touchkitusb" into blacklist to avoid conflict
if the touch controller is HID compliant device.
(Q) Which interface controller do you use?
(I) [1] RS232 [2] PS/2 [3] USB: 3
(I) Using interface: USB
(I) Found a non-HID compliant touch controller.
(W) No inbuilt kernel module for touch controller found.
(I) It is needed to build "tkusb" kernel module for touch controller.
(I) For details, see the document "How to build module.pdf".
Note that the user needs to build the eGalax Touch kernel module "tkusb"
for touch controller if the inbuilt kernel module "usbtouchscreen" or
"touchkitusb" does NOT exist in the kernel.
(*) Driver archive un-installation
root@test-desktop:~# sh setup.sh uninstall
(*) Linux driver installer for eGalax Touch controller
(I) Check user permission: root, you are the supervisor.
(I) Begin to remove eGalax Touch driver.
(I) Removed eGalax Touch driver archive from /usr/local/eGalaxTouch32.
(I) Removed eGalax Touch utility shortcut.
(I) Removed TKCal tool shortcut.
(I) Searching the X input modules directory.
(I) Removed X module.
(I) Removed blacklist usbtouchscreen from /etc/modprobe.d/blacklist.
(I) Found X configuration file: /etc/X11/xorg.conf.
(I) Removed touch configuration from /etc/X11/xorg.conf.
(I) The eGalax Touch driver has been removed successfully.
(I) Please reboot the system for some changes to take effect.
(*) The version of the installer
root@test-desktop:~# sh setup.sh version
(*) Linux driver installer for eGalax Touch controller
(I) Version: 1.03.1301
For more information about X configuration setting, please see the
section "Installation of the Xorg module manually" in the document
"Driver Guide.pdf".
# ========================================================================= #
Het eerste wat je moet doen is het script starten, dat gaat zo:
Open een terminal(onder Hulpmiddelen) en navigeer naar de map eGalax dat doe je zo:
───[gijs@gijs-desktop]──[22:52]──> /home/gijs
$ cd Downloads/eGalaxTouch32 <---------------------- hier het pad opgeven waar eGalaxTouch32 staat
Als je in de map bent geef je een dir om te zien welke bestanden er in staan.
───[gijs@gijs-desktop]──[22:52]──> /home/gijs/Downloads/eGalaxTouch32
$ dir
eGalaxTouch.tar.gz eula.pdf Guide readme setup.sh
Dan het script starten:
───[gijs@gijs-desktop]──[22:53]──> /home/gijs/Downloads/eGalaxTouch32
$ sudo sh setup.sh <---------- Geef een ENTER
[sudo] password for gijs: <--------- Hier je wachtwoord invullen, hier zie je niets van, gewoon blind typen en geef een ENTER
Hierna moet je de vragen beantwoorden:
[code](*) Linux driver installer for eGalax Touch controller
(I) Check user permission: root, you are the supervisor.
(I) Begin to setup the eGalax Touch driver.
(I) Found and removed previous eGalax Touch driver.
(I) Extract eGalax Touch driver archive to /usr/local/eGalaxTouch32.
(I) Create eGalaxTouch utility shortcut in /usr/bin.
(I) Create TKCal tool shortcut in /usr/bin.
(I) Check X window version: 6.9.0 ~ 7.2.0
(I) Copy X module: x69/egalax_drv.so to /usr/lib/xorg/modules/input.
(Q) Which interface controller do you use?
(I) [1] RS232 [2] PS/2 [3] USB :
Verder kon ik niet gaan want ik ben niet in bezit van zo'n touchscreen.
Doe eerst dit maar, daarna kan je verder met de bestanden in Guide.
[/code]