Ja, RAID0, ik wilde het ook anders zien maar 2 jaar geleden waren er og geen schijven van 1 TB, dus moest ik van mijn baas 4 x 500GB in RAUD 0 zetten om zovel mogelijk opslag te hebben voor camerabeelden.
Dit gezegd zijnde krijg ik dit als error :
root@backup2T:/var/log# mdadm --assemble --scan
mdadm: /dev/md0 assembled from 3 drives - not enough to start the array.
het lijk erop dat er een drive tekort in zit
nog een log /var/dmesg:
[ 1.878434] Copyright (c) 1999-2006 Intel Corporation.
[ 1.878479] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 1.878491] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 1.884975] ieee1394: Initialized config rom entry `ip1394'
[ 1.889753] SCSI subsystem initialized
[ 1.889820] usbcore: registered new interface driver usbfs
[ 1.889837] usbcore: registered new interface driver hub
[ 1.894985] libata version 2.20 loaded.
[ 1.903066] usbcore: registered new device driver usb
[ 1.903858] USB Universal Host Controller Interface driver v3.0
[ 1.920609] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:b1:c9:51
[ 2.042093] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 2.042125] ata_piix 0000:00:1f.2: version 2.10ac1
[ 2.042131] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 2.042152] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 2.042169] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.042211] ata1: SATA max UDMA/133 cmd 0x00012148 ctl 0x0001217e bmdma 0x00012110 irq 19
[ 2.042232] ata2: SATA max UDMA/133 cmd 0x00012140 ctl 0x0001217a bmdma 0x00012118 irq 19
[ 2.042243] scsi0 : ata_piix
[ 2.482877] ata1.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 2.482882] ata1.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
[ 2.482885] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.482888] ata1.01: ATAPI, max UDMA/33
[ 2.549489] ata1.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 2.549493] ata1.00: configured for UDMA/133
[ 2.773168] ata1.01: configured for UDMA/33
[ 2.773174] scsi1 : ata_piix
[ 2.999653] ata2.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 2.999656] ata2.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
[ 2.999659] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.074595] ata2.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 3.074600] ata2.00: configured for UDMA/133
[ 3.074686] scsi 0:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
[ 3.075830] scsi 0:0:1:0: CD-ROM TSSTcorp DVD-ROM SH-D163B SB00 PQ: 0 ANSI: 5
[ 3.075987] scsi 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
[ 3.076092] ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
[ 3.076107] ACPI: PCI Interrupt 0000:00:1f.5[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.076119] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 3.076139] ata3: SATA max UDMA/133 cmd 0x00012138 ctl 0x00012176 bmdma 0x000120f0 irq 19
[ 3.076157] ata4: SATA max UDMA/133 cmd 0x00012130 ctl 0x00012172 bmdma 0x000120f8 irq 19
[ 3.076162] scsi2 : ata_piix
[ 3.297744] ata3.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 3.297749] ata3.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
[ 3.297751] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.372680] ata3.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 3.372685] ata3.00: configured for UDMA/133
[ 3.372689] scsi3 : ata_piix
[ 3.601405] ata4.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 3.601409] ata4.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
[ 3.601412] ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.676347] ata4.00: ata_hpa_resize 1: sectors = 976773168, hpa_sectors = 976773168
[ 3.676351] ata4.00: configured for UDMA/133
[ 3.676419] scsi 2:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
[ 3.676571] scsi 3:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
[ 3.676694] ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 3.726838] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[90004000-900047ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 3.728578] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 3.728587] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 3.728591] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 3.728675] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 3.728699] uhci_hcd 0000:00:1a.0: irq 17, io base 0x000020a0
[ 3.728785] usb usb1: configuration #1 chosen from 1 choice
[ 3.728808] hub 1-0:1.0: USB hub found
[ 3.728813] hub 1-0:1.0: 2 ports detected
[ 3.837077] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 3.837084] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 3.837088] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 3.837108] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 3.837131] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00002080
[ 3.837208] usb usb2: configuration #1 chosen from 1 choice
[ 3.837232] hub 2-0:1.0: USB hub found
[ 3.837237] hub 2-0:1.0: 2 ports detected
[ 3.947503] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 22
[ 3.947510] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 3.947514] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.947532] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 3.947556] uhci_hcd 0000:00:1d.0: irq 22, io base 0x00002060
[ 3.947634] usb usb3: configuration #1 chosen from 1 choice
[ 3.947656] hub 3-0:1.0: USB hub found
[ 3.947661] hub 3-0:1.0: 2 ports detected
[ 4.057902] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 4.057909] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 4.057912] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.057931] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[ 4.057952] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002040
[ 4.058030] usb usb4: configuration #1 chosen from 1 choice
[ 4.058052] hub 4-0:1.0: USB hub found
[ 4.058057] hub 4-0:1.0: 2 ports detected
[ 4.168307] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 4.168314] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 4.168317] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.168336] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[ 4.168360] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002020
[ 4.168438] usb usb5: configuration #1 chosen from 1 choice
[ 4.168459] hub 5-0:1.0: USB hub found
[ 4.168464] hub 5-0:1.0: 2 ports detected
[ 4.278726] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 4.278731] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 4.278743] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 4.278746] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 4.278748] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 4.278772] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
[ 4.278797] ehci_hcd 0000:00:1a.7: debug port 1
[ 4.278803] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 4.278807] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x90326400
[ 4.282698] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.282754] usb usb6: configuration #1 chosen from 1 choice
[ 4.282775] hub 6-0:1.0: USB hub found
[ 4.282779] hub 6-0:1.0: 4 ports detected
[ 4.282808] ata5: PATA max UDMA/100 cmd 0x00011018 ctl 0x00011026 bmdma 0x00011000 irq 16
[ 4.282820] scsi4 : pata_marvell
[ 4.282861] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00
[ 4.460764] ATA: abnormal status 0x8 on port 0x0001101f
[ 4.460814] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 22
[ 4.460822] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4.460825] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.460844] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 4.460867] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.460872] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 4.460876] ehci_hcd 0000:00:1d.7: irq 22, io mem 0x90326000
[ 4.464758] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.464813] usb usb7: configuration #1 chosen from 1 choice
[ 4.464833] hub 7-0:1.0: USB hub found
[ 4.464838] hub 7-0:1.0: 6 ports detected
[ 4.575495] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.575505] sda: Write Protect is off
[ 4.575507] sda: Mode Sense: 00 3a 00 00
[ 4.575519] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.575555] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.575563] sda: Write Protect is off
[ 4.575565] sda: Mode Sense: 00 3a 00 00
[ 4.575577] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.575579] sda: sda1 sda2 sda3 sda4
[ 4.605550] sd 0:0:0:0: Attached scsi disk sda
[ 4.606084] SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.606093] sdb: Write Protect is off
[ 4.606095] sdb: Mode Sense: 00 3a 00 00
[ 4.606108] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.606143] SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.606151] sdb: Write Protect is off
[ 4.606152] sdb: Mode Sense: 00 3a 00 00
[ 4.606164] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.606166] sdb:sr0: scsi3-mmc drive: 4x/48x cd/rw xa/form2 cdda tray
[ 4.618841] Uniform CD-ROM driver Revision: 3.20
[ 4.618874] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 4.622226] sdb1
[ 4.622261] sd 1:0:0:0: Attached scsi disk sdb
[ 4.622544] SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.622553] sdc: Write Protect is off
[ 4.622555] sdc: Mode Sense: 00 3a 00 00
[ 4.622567] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.622596] SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.622604] sdc: Write Protect is off
[ 4.622606] sdc: Mode Sense: 00 3a 00 00
[ 4.622617] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.622620] sdc: sdc1
[ 4.636524] sd 2:0:0:0: Attached scsi disk sdc
[ 4.636567] SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.636577] sdd: Write Protect is off
[ 4.636579] sdd: Mode Sense: 00 3a 00 00
[ 4.636593] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.636626] SCSI device sdd: 976773168 512-byte hdwr sectors (500108 MB)
[ 4.636635] sdd: Write Protect is off
[ 4.636637] sdd: Mode Sense: 00 3a 00 00
[ 4.636651] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.636653] sdd: sdd1
[ 4.657077] sd 3:0:0:0: Attached scsi disk sdd
[ 4.664262] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.664280] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 4.664299] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 4.664316] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 4.664333] sd 3:0:0:0: Attached scsi generic sg4 type 0
[ 4.776473] md: md0 stopped.
[ 4.836728] md: bind<sdd1>
[ 4.836854] md: bind<sdc1>
[ 4.873015] md: array md0 already has disks!
[ 4.907971] md: array md0 already has disks!
[ 4.921490] md: array md0 already has disks!
[ 4.924376] md: array md0 already has disks!
[ 4.927123] md: array md0 already has disks!
[ 4.929926] md: array md0 already has disks!
[ 4.932689] md: array md0 already has disks!
[ 4.935228] md: array md0 already has disks!
[ 4.937770] md: array md0 already has disks!
[ 4.940299] md: array md0 already has disks!
[ 4.942838] md: array md0 already has disks!
[ 4.950751] md: array md0 already has disks!
[ 4.959993] Attempting manual resume
[ 4.959996] swsusp: Resume From Partition 8:2
[ 4.959997] PM: Checking swsusp image.
[ 4.960111] PM: Resume from disk failed.
[ 4.981749] kjournald starting. Commit interval 5 seconds
[ 4.981756] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.982283] md: array md0 already has disks!
[ 5.052484] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090270001e98a99]
[ 5.079816] md: array md0 already has disks!
[ 6.609390] e1000: eth0: e1000_request_irq: Unable to allocate MSI interrupt Error: -22
[ 6.621779] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
[ 7.251133] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 7.268787] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.321608] Linux agpgart interface v0.102 (c) Dave Jones
[ 7.379110] iTCO_vendor_support: vendor-support=0
[ 7.439182] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[ 7.439243] iTCO_wdt: Found a ICH8DO TCO device (Version=2, TCOBASE=0x0460)
[ 7.439271] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 7.456904] agpgart: Detected an Intel 965Q Chipset.
[ 7.457850] agpgart: Unknown page table size, assuming 512KB
[ 7.457854] agpgart: Detected 7676K stolen memory.
[ 7.470437] agpgart: AGP aperture is 256M @ 0x80000000
[ 7.691608] md: md0 stopped.
[ 7.691616] md: unbind<sdc1>
[ 7.691622] md: export_rdev(sdc1)
[ 7.691681] md: unbind<sdd1>
[ 7.691684] md: export_rdev(sdd1)
[ 7.718066] NET: Registered protocol family 10
[ 7.718140] lo: Disabled Privacy Extensions
[ 7.895969] input: PC Speaker as /class/input/input2
[ 7.909308] md: bind<sdc1>
[ 7.913571] md: bind<sdd1>
[ 7.913690] md: bind<sda4>
[ 7.942079] parport: PnPBIOS parport detected.
[ 7.942154] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 7.958007] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 23
[ 7.958024] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 8.095005] md: md0 stopped.
[ 8.095013] md: unbind<sda4>
[ 8.095019] md: export_rdev(sda4)
[ 8.095027] md: unbind<sdd1>
[ 8.095031] md: export_rdev(sdd1)
[ 8.095046] md: unbind<sdc1>
[ 8.095049] md: export_rdev(sdc1)
[ 8.126765] md: bind<sdc1>
[ 8.126905] md: bind<sdd1>
[ 8.127024] md: bind<sda4>
[ 9.293141] lp0: using parport0 (interrupt-driven).
[ 9.427374] Adding 1461904k swap on /dev/disk/by-uuid/52ddc541-6912-4753-906d-ee68dcbb877b. Priority:-1 extents:1 across:1461904k
[ 9.518209] EXT3 FS on sda3, internal journal
[ 9.629881] md: md0 stopped.
[ 9.629889] md: unbind<sda4>
[ 9.629897] md: export_rdev(sda4)
[ 9.629942] md: unbind<sdd1>
[ 9.629946] md: export_rdev(sdd1)
[ 9.629956] md: unbind<sdc1>
[ 9.629960] md: export_rdev(sdc1)
[ 9.711003] md: bind<sdc1>
[ 9.711120] md: bind<sdd1>
[ 9.711264] md: bind<sda4>
[ 18.681657] eth0: no IPv6 routers present
[ 55.201157] kjournald starting. Commit interval 5 seconds
[ 55.201359] EXT3 FS on sda1, internal journal
[ 55.201373] EXT3-fs: mounted filesystem with ordered data mode.
Daar hou ik dus van, hier kan je van leren (alhoewel mijn baas niet gelukkig is).
Wat is hier het probleem?
mvg
John