[ 19.308000] ndiswrapper version 1.45 loaded (smp=yes)
Volgende gegevens krijg als ik dmesg in terminal typ.
Nu heb ik volgend probleem kunnen ontdekken: zie men acces point wel maar kan hier niet mee communiceren.
Iemand een idee hoe dit komt
[ 19.384000] iTCO_vendor_support: vendor-support=0
[ 19.420000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[ 19.424000] Linux video capture interface: v2.00
[ 19.448000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x23aeb3, caps: 0xa04713/0x10008
[ 19.476000] usb 5-8: reset high speed USB device using ehci_hcd and address 4
[ 19.480000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
[ 19.480000] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[ 19.480000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 19.516000] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (064e:a100)
[ 19.712000] ndiswrapper: driver net8187b (Realtek Semiconductor Corp.,07/18/2007,5.1097.0718.2007) loaded
[ 19.748000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 19.748000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 21.332000] hda_intel: azx_get_response timeout, switching to polling mode...
[ 23.228000] wlan0: ethernet device 00:07:ca:07:05:e5 using NDIS driver: net8187b, version: 0x1, NDIS version: 0x500, vendor: 'Realtek RTL8187 Wireless LAN USB NIC', 0BDA:8189.F.conf
[ 23.228000] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[ 23.228000] usbcore: registered new interface driver ndiswrapper
[ 23.228000] usbcore: registered new interface driver uvcvideo
[ 23.228000] USB Video Class driver (v0.1.0)
[ 23.484000] lp: driver loaded but no devices found
[ 23.584000] Adding 4803392k swap on /dev/sdb5. Priority:-1 extents:1 across:4803392k
[ 24.056000] EXT3 FS on sdb1, internal journal
[ 25.068000] No dock devices found.
[ 25.104000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 25.128000] ACPI: AC Adapter [ADP1] (on-line)
[ 25.192000] ACPI: Battery Slot [BAT0] (battery absent)
[ 25.264000] input: Power Button (FF) as /class/input/input3
[ 25.264000] ACPI: Power Button (FF) [PWRF]
[ 25.308000] input: Lid Switch as /class/input/input4
[ 25.312000] ACPI: Lid Switch [LID0]
[ 25.312000] input: Sleep Button (CM) as /class/input/input5
[ 25.312000] ACPI: Sleep Button (CM) [SLPB]
[ 26.488000] ppdev: user-space parallel port driver
[ 26.684000] audit(1208103562.295:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5353 profile="/usr/sbin/cupsd"
[ 26.744000] apm: BIOS not found.
[ 27.076000] Failure registering capabilities with primary security module.
[ 27.320000] Bluetooth: Core ver 2.11
[ 27.320000] NET: Registered protocol family 31
[ 27.320000] Bluetooth: HCI device and connection manager initialized
[ 27.320000] Bluetooth: HCI socket layer initialized
[ 27.360000] Bluetooth: L2CAP ver 2.8
[ 27.360000] Bluetooth: L2CAP socket layer initialized
[ 27.488000] Bluetooth: RFCOMM socket layer initialized
[ 27.488000] Bluetooth: RFCOMM TTY layer initialized
[ 27.488000] Bluetooth: RFCOMM ver 1.8
[ 32.596000] [drm] Initialized drm 1.1.0 20060810
[ 32.600000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 32.600000] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 64.176000] NET: Registered protocol family 10
[ 64.176000] lo: Disabled Privacy Extensions
[ 64.176000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 64.176000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1323.540000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1462.456000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1462.480000] ndiswrapper (add_wep_key:798): adding encryption key 1 failed (C0010015)
[ 1630.380000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1632.412000] ADDRCONF(NETDEV_UP): wlan0: link is not ready