Waar vind ik isapnp en hoe doe ik dat?
Ok, heb dit na nog wat verder te zoeken op het forum gevonden en geïnstalleerd.
Dit is het resultaat als ik sudo pnpdump doe:
karel@Bells:~$ sudo pnpdump
[sudo] password for karel:
# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
#
http://www.roestock.demon.co.uk/isapnptools/#
# Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier 10 ff ff ff ff 20 01 93 05
# Board 2 has serial identifier 37 08 28 98 ca 95 50 6d 50
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier 10 ff ff ff ff 20 01 93 05)
# Vendor Id ALS0120, No Serial Number (-1), checksum 0x10.
# Version 1.0, Vendor version 0.0
# ANSI string -->PnP Sound Chip <--
#
# Logical device id @@@2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ALS0120/-1 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 1))
# Next DMA channel 0 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0100) (CHECK))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# End dependent functions
(NAME "ALS0120/-1[0]{PnP Sound Chip }")
# (ACT Y)
))
#
# Logical device id @H@2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ALS0120/-1 (LD 1
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0388) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x07ff
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0300) (CHECK))
# End dependent functions
(NAME "ALS0120/-1[1]{PnP Sound Chip }")
# (ACT Y)
))
#
# Logical device id @P@2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ALS0120/-1 (LD 2
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x07ff
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# End dependent functions
(NAME "ALS0120/-1[2]{PnP Sound Chip }")
# (ACT Y)
))
#
# Logical device id @X@2001
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE ALS0120/-1 (LD 3
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330) (CHECK))
# IRQ 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(NAME "ALS0120/-1[3]{PnP Sound Chip }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier 37 08 28 98 ca 95 50 6d 50)
# Vendor Id TCM5095, Serial Number 136878282, checksum 0x37.
# Version 1.0, Vendor version 1.0
# ANSI string -->3Com 3C509B EtherLink III<--
#
# Logical device id TCM5095
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TCM5095/136878282 (LD 0
# Compatible device id PNP80f7
# IRQ 3, 5, 7, 9, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x03e0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0210) (CHECK))
(NAME "TCM5095/136878282[0]{3Com 3C509B EtherLink III}")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
karel@Bells:~$
Het is dus blijkbaar toch een pnp kaart en ze wordt teruggevonden.
Kan iemand mij vertellen hoe ik ze toch aan de praat kan krijgen?
Waarom 15 euro spenderen aan een nieuwe kaart, als de originele misschien toch werkt?