Vistaus, lmsensors werkt wel? of ook niet?pwmconfig is nl. een onderdeel van lmsensors.
Dit zou het moeten zijn:
gijs@gijs-desktop:~$ sudo pwmconfig
[sudo] password for gijs:
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
Found the following devices:
hwmon0/device is it8718
hwmon1/device is coretemp
hwmon2/device is coretemp
Found the following PWM controls:
hwmon0/device/pwm1
hwmon0/device/pwm2
hwmon0/device/pwm3
Giving the fans some time to reach full speed...
Found the following fan sensors:
hwmon0/device/fan1_input current speed: 2136 RPM
hwmon0/device/fan2_input current speed: 0 ... skipping!
Warning!!! This program will stop your fans, one at a time,
for approximately 5 seconds each!!!
This may cause your processor temperature to rise!!!
If you do not want to do this hit control-C now!!!
Hit return to continue:
Testing pwm control hwmon0/device/pwm1 ...
hwmon0/device/fan1_input ... speed was 2136 now 2142
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon0/device/pwm1,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)?
Testing pwm control hwmon0/device/pwm2 ...
hwmon0/device/fan1_input ... speed was 2136 now 2149
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon0/device/pwm2,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)?
Testing pwm control hwmon0/device/pwm3 ...
hwmon0/device/fan1_input ... speed was 2136 now 2149
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon0/device/pwm3,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)?
Testing is complete.
Please verify that all fans have returned to their normal speed.
The fancontrol script can automatically respond to temperature changes
of your system by changing fanspeeds.
Do you want to set up its configuration file now (y)?
What should be the path to your fancontrol config file (/etc/fancontrol)?
/etc/fancontrol does not exist, shall I create it now (y)?
Loading configuration from /etc/fancontrol ...
Select fan output to configure, or other action:
1) Change INTERVAL 3) Save and quit
2) Just quit 4) Show configuration
select (1-n): 4
Common Settings:
INTERVAL=10
Select fan output to configure, or other action:
1) Change INTERVAL 3) Save and quit
2) Just quit 4) Show configuration
select (1-n):Heb je misschien Ubuntu de 64 bit uitvoering? Ik weet niet of het iets uitmaakt, is zomaar een idee.
Met vriendelijke groet,
Gijs
