Kom er niet uit, veel gelezen en gewijzigd, maar nu wordt ik er een beetje moedeloos van, heb de volgende gegevens,
heb middels ndiswrapper mijn wireless sweex pcmcia kaart geactiveerd.
heb nu de volgende gegevens:
alex@ibm:/$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.462 GHz Access Point: 00:00:00:00:00:00
Bit Rate:54 Mb/s Tx-Power:16 dBm
RTS thr:2347 B Fragment thr:2346 B
Power Management:off
Link Quality:100/100 Signal level:-10 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:44381 Missed beacon:0
sit0 no wireless extensions.
alex@ibm:/$ lspci
0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
0000:00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
0000:00:03.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 09)
0000:00:03.1 Serial controller: Xircom Mini-PCI V.90 56k Modem
0000:00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
0000:00:07.0 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
0000:01:00.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/IX-MV (rev 11)0000:06:00.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)
alex@ibm:/$
alex@ibm:/$ sudo iwlist wlan0 scan
Password:
wlan0 Scan completed :
Cell 01 - Address: 00:13:D4:6E:DA:FD
ESSID:"Versatel"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.457 GHz (Channel 10)
Quality:0/100 Signal level:-48 dBm Noise level:-256 dBm
Encryption key:on
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Bit Rate:18 Mb/s
Bit Rate:24 Mb/s
Bit Rate:36 Mb/s
Bit Rate:54 Mb/s
Bit Rate:6 Mb/s
Bit Rate:9 Mb/s
Bit Rate:12 Mb/s
Bit Rate:48 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 02 - Address: 00:04:E2:8B:20:9B
ESSID:"HOMEGROUP"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:0/100 Signal level:-46 dBm Noise level:-256 dBm
Encryption key:on
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Bit Rate:6 Mb/s
Bit Rate:9 Mb/s
Bit Rate:12 Mb/s
Bit Rate:18 Mb/s
Bit Rate:24 Mb/s
Bit Rate:36 Mb/s
Bit Rate:48 Mb/s
Bit Rate:54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Extra:wpa_ie=dd180050f20101000050f20501000050f20201000050f2020000
Cell 03 - Address: 00:0C:41:67:D6:66
ESSID:"Versatel"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.457 GHz (Channel 10)
Quality:0/100 Signal level:-48 dBm Noise level:-256 dBm
Encryption key:on
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Extra:bcn_int=100
Extra:atim=0
Via de wireless adapter ziet hij op een of andere manier wel de wireless accesspoints echter middels WEP maakt hij geen connectie met de wireless router HOMEGROUP.
De led welke de datafunctie aangeeft is inactief, de power led is wel actief. Hoe krijg ik dat de adapter ook daadwerkelijk actief gaat zenden en ontvangen van pakketten
Indien meer input verlangt wordt, verneem ik dat graag.
Ben wel een beginner met linux maar redelijk wat automatiseringskennis op breed gebied echter (li-)unix is altijd wat achter gebleven wat ik nu wil opfrissen.
Thanks voor alle input.
gr
Shotfac
