gelukt om de nouveau te blacklisten. daarna gereboot en nu gelukt om de nvidia driver te installeren.
maar.....nu moet er nog een XF86Config of Xorg.conf gemaakt worden ofzo.......en nu ben ik er totaal af.
als ik de computer op start dan komt er in elk geval beeld.....alleen met een 640x480 en is de enige keuze.
is er een commando bekend die zoiets automatisch kan doen of kan dat alleen handmatig ?
onderstaand is een sample voorbeeld die in usr/share/doc na de installatie is te vinden.
is hier iets mee te beginnen ?
##########################################################################
# Sample XF86Config file for NVIDIA XFree86 drivers.
#
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
#
# Be sure to replace the monitor values with correct values for your
# monitor!
##########################################################################
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "unix/:-1"
EndSection
##########################################################################
# Server flags section.
##########################################################################
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
#NoTrapSignals
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
#DontZap
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
#DontZoom
# This allows the server to start up even if the
# mouse device can't be opened/initialised.
AllowMouseOpenFail
EndSection
##########################################################################
# Input devices
##########################################################################
#
# Keyboard section
#
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
Option "AutoRepeat" "250 30"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
#
# Pointer section
#
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/psaux"
EndSection
##########################################################################
# Module section
##########################################################################
Section "Module"
Load "dbe"
# Load the glx module.
Load "glx"
Load "extmod"
Load "type1"
Load "freetype"
EndSection
##########################################################################
# Monitor section
##########################################################################
Section "Monitor"
Identifier "MyMonitor"
VendorName "Mitsubisi"
ModelName "Diamond Plus 120u"
# be sure to replace these values with values appropriate for your
# monitor!
HorizSync 31-82
VertRefresh 55-120
# 3840x2400 @ 12Hz for IBM's T221 FlatPanel
Modeline "3840x2400" 148.0 3840 3944 4328 4816 2400 2401 2404 2418
EndSection
##########################################################################
# Graphics device section(s)
##########################################################################
Section "Device"
Identifier "NV AGP"
VendorName "nvidia"
Driver "nvidia"
# update this with the PCI id of your card. Consult the output
# of the 'lspci' command. The BusID is usually optional when
# only using one graphics card.
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "NV PCI"
VendorName "nvidia"
Driver "nvidia"
# update this with the PCI id of your card. Consult the output
# of the 'lspci' command. The BusID is usually optional when
# only using one graphics card.
BusID "PCI:0:13:0"
EndSection
Section "Device"
Identifier "NV AGP TwinView"
VendorName "nvidia"
Driver "nvidia"
# update this with the PCI id of your card. Consult the output
# of the 'lspci' command. The BusID is usually optional when
# only using one graphics card.
BusID "PCI:1:0:0"
# sample twinview setup
Option "TwinView"
# be sure to replace the HorizSync and VertRefresh with correct values
# for your monitor!
Option "SecondMonitorHorizSync" "31-82"
Option "SecondMonitorVertRefresh" "55-120"
Option "TwinViewOrientation" "RightOf"
Option "MetaModes" "1280x1024,1280x1024; 1024x768,1024x768"
Option "ConnectedMonitor" "crt,crt"
EndSection
##########################################################################
# Screen sections
##########################################################################
#
# screen section for an nvidia AGP card
#
Section "Screen"
Identifier "Screen AGP"
Device "NV AGP"
Monitor "MyMonitor"
DefaultColorDepth 24
Subsection "Display"
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x400"
EndSubsection
Subsection "Display"
Depth 16
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
EndSection
#
# screen section for an nvidia PCI card
#
Section "Screen"
Identifier "Screen PCI"
Device "NV PCI"
Monitor "MyMonitor"
DefaultColorDepth 24
Subsection "Display"
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x400"
EndSubsection
Subsection "Display"
Depth 16
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
EndSection
#
# screen section for an nvidia AGP TwinView card
# (look at the appropriate Device section)
#
Section "Screen"
Identifier "Screen AGP TwinView"
Device "NV AGP TwinView"
Monitor "MyMonitor"
DefaultColorDepth 24
Subsection "Display"
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x400"
EndSubsection
Subsection "Display"
Depth 16
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
EndSubsection
EndSection
##########################################################################
# ServerLayout sections
# (invoke using the '-layout' option of 'startx'.
##########################################################################
#
# just one agp card
#
Section "ServerLayout"
Identifier "AGP"
Screen "Screen AGP"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
#
# just one pci card
#
Section "ServerLayout"
Identifier "PCI"
Screen "Screen PCI"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
#
# 2 cards, non twinview
#
Section "ServerLayout"
Identifier "Both"
Screen "Screen AGP"
Screen "Screen PCI" LeftOf "Screen AGP"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
#
# just one agp twinview card
#
Section "ServerLayout"
Identifier "AGPTwinView"
Screen "Screen AGP TwinView"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
#
# 2 cards, one agp twinview and one pci (3 monitors total)
#
Section "ServerLayout"
Identifier "BothTwinView"
Screen "Screen AGP TwinView"
Screen "Screen PCI" LeftOf "Screen AGP TwinView"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
ook zie ik nvidia-settings.png in deze folder staan. kan dit worden gebruikt of is dat iets voor na xorg.conf te gebruiken ?